Burke Fire Doors - Google 2023 - Watermarque

• Audit Title

• Document/Asset No.

• Client / Site

  Select

• Conducted on

  Date

• Prepared by

• Location
  Address

• Other Location info:

• Door Type

  Select

• Estimated time to repair

Door Information

• Is there a fire tag present on this door?

  yes

  no

• What is the Fire rating on this fire door?

  FD30

  FD30(s)

  FD60

  FD60(s)

• Based on the thickness of the door, what is the assumed fire rating of this door??

  FD30

  FD30(s)

  FD60

  FD60(s)

• What are the overall dimensions of this door?

TOLERANCES - Doors should be hung to give an equal gap across the head, down both jambs and at the meeting edges (BS 8214:2016 - section 9.5.2). Failure of fire resisting door assemblies under test is very often due to burn through at the operating gap between the door leaf and the door frame. The typical gap as per certification is between 2mm and 4mm maximum.

• T1 - Margins - Hinge Side

  Compliant

  Non-Compliant

  N/A

• T2 - Margins - Latch Side

  Compliant

  Non-Compliant

  N/A

• T3 - Margins - Head of the door

  Compliant

  Non-Compliant

  N/A

• T4 - Margins - Threshold - 3mm for Fire and Smoke, maximum 10mm for non-smoke

  Compliant

  Non-Compliant

  N/A

• T5 - Incorrect Clearance ( Between Pairs of Doors )

  Compliant

  Non-Compliant

  N/A

• T6 - Any other comments

DOOR FRAME

• F1 - Is the overall condition of the door frame acceptable? I.e. is there any significant damage that could hinder the performance of the fire door assembly?

  Yes

  No

  N/A

• F2 - Is the timber used acceptable? Softwood or hardwood frames are required for FD30(s) fire resistance while hardwood frames are required for FD60(s) fire resistance.

  Yes

  No

  N/A

• F3 - Door Stop - stops must be a minimum 12mm deep, pinned and/or glued into position

  Compliant

  Non-Compliant

  N/A

• F4 - Are the door frame joints acceptable? - all joints must be robust and mechanically fixed. The visible joint line must be secure with no visible gaps.

  Yes

  No

  N/A

• F5 - Intumescent Seals - intumescent should be installed in the door frame or the door edges. Seals should be damage free and consistent around the door frame.

  yes

  no

• F8 - Architrave - is there architrave installed?

  Yes

  No

• F9 - Architrave - is the architrave installation adequate? 15mm coverage And minimum 15mm thick?

  Compliant

  Non-Compliant

  N/A

• F10 - Any other comments

DOOR

• D1 - Is the relative condition of the door leaf good? Is there any significant evidence of damage that will hinder the performance of the fire door assembly?

  Compliant

  Non-Compliant

  N/A

• D2 - Door edge - is the relative condition of the door edge good?

  Compliant

  Non-Compliant

  N/A

• D3 - Closure to the frame - are alignment tolerances adequate? Doors must not be proud of each other or from the frame by more than 1mm

  Compliant

  Non-Compliant

  N/A

• D4 - Fire Signage - is the correct fire signage affixed to the face of the door? Fire door keep shut signs should be present on both sides of the door. For doors that are kept in the locked position (I.e. Riser doors) fire door keep locked signs should be installed

  Compliant

  Non-Compliant

  N/A

• D5 - Any other comments

OPERATIONAL TEST

• O1 - Can the door open and close adequately?

  Yes

  No

  N/A

• O2 - Can the door latch securely?

  Yes

  No

  N/A

• O3 - Any other comments

HARDWARE

• H1 - Is there a self closing device installed? Fire doors can only operate correctly if they are fully closed at the time of the fire (BS 8214:2016 - section 11.4)

  Yes

  No

  N/A

• H2 - Is the self closing device operating correctly?

  Yes

  No

  N/A

• H3 - Hinges - are they installed correctly?

  Yes

  No

  N/A

• H4 - Hinges - all screws present?

  Yes

  No

  N/A

• H5 - Hinges - are they CE/EN marked?

  Yes

  No

  N/A

• H6 - Hinges - is there intumescent protection behind the hinge?

  Yes

  No

  N/A

• H7 - Locks - IS there a lock installed on this door?

  Yes

  No

• H7 - Locks - position between 900mm to 1200mm from finished floor level

  Compliant

  Non-Compliant

  N/A

• H8 - Locks - is the lock CE/EN marked?

  Yes

  No

  N/A

• H9 - Locks - is there intumescent protection around the lock case?

  Yes

  No

  N/A

• H10 - Flush Bolts - Are there flush bolts installed on this door?

  Yes

  No

• H10 - Flush Bolts - can the bolt operate and engage properly?

  yes

  no

• H11 - Flush Bolts - is there intumescent protection around the flush bolt?

  Yes

  No

  N/A

• H12 - Any other information?

GLAZING

• G1 - Does the door have a vision panel?

  Yes

  No

• G3 - What is the overall dimension of the glazed vision panel? For compliance a review must be undertaken from the manufacturer test evidence

• G2 - Is the glass stamped with its type, fire rating and manufacturer? All glass marking should be permanent and clear, able to be seen and read after installation in the door

  Yes

  No

  N/A

• G4 - What is the overall dimension of the glazing bead?

• G5 - Is there fire glazing intumescent behind the glazing bead?

  Yes

  No

  N/A

• G6 - Any other information

Fire Mastic

• F1 - Are you inspecting the fire mastic on this door? ie. removing architrave ?

  Yes

  No

• F2 - Gap up to 10mm - is the installation acceptable?

  Compliant

  Non-Compliant

  N/A

• F3 - Gap from 10mm to 20mm - is the installation acceptable?

  Compliant

  Non-Compliant

  N/A

• F4 - Gap from 20mm and beyond - is the installation acceptable?

  Compliant

  Non-Compliant

  N/A