Kdec Solar Commissioning Form

• Site conducted

  Select

• GeoOP job number

• Client / Site

• Conducted on

  Date

• Prepared by

• Location
  Address

Solar Module Details

• PV module manufacturer and model number

  Select Sunpower E20 327W Sunpower X21 335W Sunpower P19 315W Sunpower P19 320W Sunpower P19 325W Sunpower P19 390W Sunpower P19 395W Q-Cell G4 310W Q-Cell G5 275W Q-Cell G5 325W Sapphire gem 270W Trina Honey 300W Other - note below

  • Sunpower E20 327W
  • Sunpower X21 335W
  • Sunpower P19 315W
  • Sunpower P19 320W
  • Sunpower P19 325W
  • Sunpower P19 390W
  • Sunpower P19 395W
  • Q-Cell G4 310W
  • Q-Cell G5 275W
  • Q-Cell G5 325W
  • Sapphire gem 270W
  • Trina Honey 300W
  • Other - note below

• Number of solar modules

• String configurations

Inverter Details

Inverter

• Inverter manufacturer

• Inverter model number

• Inverter Serial Number

• Number of MPPTs

Installation Checkoff

• Array frame is certified to AS1170.2 for installation location

• Array frame is installed to to manufacturers instructions

• No galvanically dissimilar metals are in contact with the array frames or supports

• Roof penetrations are suitably sealed and weatherproofed

• PV wiring losses are less than 3% at the maximum current output of the array

• Where PV array comprises multiple strings, string protection has been provided

• Wiring is protected from mechanical damage and is appropriately supported

• Weatherproof PV isolator mounted adjacent to array

  ZJ BENY 1000V 32A

  Benedict 1000V 32A

  Benedict 1000V 55A

  Built into inverter

• All low voltage wiring has been installed by a licensed electrical tradesperson

• All wiring has been tested and approved by a qualified electrical tradesperson

• PV array isolator mounted adjacent to the inverter

  ZJ BENY 1000V 32A

  Benedict 1000V 32A

  Benedict 1000V 55A

  Built into inverter

• Isolator is mounted on output of inverter

• Lockable AC circuit breaker is mounted within the switchboard to act as the inverter main switch for the PV/inverter

  Select 16 Amp 20 Amp 25 Amp 32 Amp

  • 16 Amp
  • 20 Amp
  • 25 Amp
  • 32 Amp

• Inverter is installed to manufacturers specification

• Inverter ceases supplying power within 2 seconds of a loss of mains power

• Inverter does not resume supplying power until mains have been present for more than 60 seconds

• All labels are installed to CEC and Australian Standards

Continuity check

• Continuity of all strings, sub-arrays and array cables

  Compliant

  Non-compliant

• Continuity of all earth connections (including module frame)

  Compliant

  Non-compliant

Insulation resistance measurements

• Array Positive to earth M ohm

  > 1 M ohm

  < 1 M ohm

• Array negative to earth M ohm

  > 1 M ohm

  < 1 M ohm

System Commissioning check

• String Test Results

String

• String tilt and orientation

• String polarity

• Irradiance at time of testing

• String measured Voc

• String operating voltage

• String measured Isc

• String operating current

Anti Islanding Test

• Time for inverter to disconnect is less than 2 seconds

  Pass

  Fail

• Time for inverter to reconnect greater than 60 seconds

  Pass

  Fail

Installers Information

• Name and CEC Accreditation number of Installer

  Select Kyle Schubert - A3956368 Gavin Mascas - A6898487 Chris van Zanten - A1575465 Mark Doolan - A9768638 Mitch Blatchford - A6073247 Andrew Lyell - Cameron Walker - A9975582 Steve Lowe - A1930000 Adam Mann -

  • Kyle Schubert - A3956368
  • Gavin Mascas - A6898487
  • Chris van Zanten - A1575465
  • Mark Doolan - A9768638
  • Mitch Blatchford - A6073247
  • Andrew Lyell -
  • Cameron Walker - A9975582
  • Steve Lowe - A1930000
  • Adam Mann -

• CEC Designer and Installers signature

  Sign

• Name and Licence of Electrician

  Select Kyle Schubert - A54184 - 75163S Gavin Mascas - A56033 - 299764C Chris van Zanten - A142103 - 293549C Mitch Blatchford - A47066 - 210055C Andrew Lyell - A59501 - 67294S Adam Mann - A57373 Mark Doolan - A50178 - 68022S Cameron Walker - E37355 - 39795S Steve Lowe - A27128 - 286411C

  • Kyle Schubert - A54184 - 75163S
  • Gavin Mascas - A56033 - 299764C
  • Chris van Zanten - A142103 - 293549C
  • Mitch Blatchford - A47066 - 210055C
  • Andrew Lyell - A59501 - 67294S
  • Adam Mann - A57373
  • Mark Doolan - A50178 - 68022S
  • Cameron Walker - E37355 - 39795S
  • Steve Lowe - A27128 - 286411C

• Electricians signature

  Sign

undefined

• Supply Requirements

  Overhead

  Underground

  Overhead to underground conversion

• Supply Phases

  1

  2

  3

• CT requirements

  Yes

  No

• Off Peak Requirements

  None

  Hot Water

  Floor heat

  Hot water and Floor Heat