Lidl - Oven Project - 1.2

• Store No:

• Store Name

• Store Location
  Address

• Installation Date

  Date

Details

• Lead Engineer Name:

Pre Works Checks

• Picture of Oven Area Prior to Works

  Media

• Picture of Cabs Prior to Works

  Media

• Picture of any Damage or Areas of Concern

  Media

Cabling Installation.

• Network Ports Plates must be mounted securely to the wall.
  
  There must be no visible cracks or damage to the housing.
  
  The ports must be firm to the touch and securely connected.
  
  The ports must be clearly labelled as with the existing store standard (Device and Port Patch Information)
  
  Each port must be tested from socket to patch panel and correctly labelled

• Patching:
  Schafer Rack
  
  Device Patch Panel Switch Port VLAN
  
  Oven 1 SCHAFER-P2-38 NS03 1 210
  
  Oven 2 SCHAFER-P2-41 NS03 4 210
  
  Oven 3 SCHAFER-P2-43 NS03 18 210
  
  Oven 4 SCHAFER-P2-44 NS03 17 210
  
  Oven 5 SCHAFER-P2-32 NS03 24 210
  
  Oven 6 SCHAFER-P2-34 NS03 23 210
  
  ATTOCK Rack
  
  Device Patch Panel Switch Port VLAN
  
  Oven 1 R2-P7-01 NS03 1 210
  
  Oven 2 R2-P9-01 NS04 1 210
  
  Oven 3 R2-P6-02 NS03 4 210
  
  Oven 4 R2-P8-02 NS04 4 210
  
  Oven 5 R2-P6-09 NS03 18 210
  
  Oven 6 R2-P8-09 NS04 18 210

Oven Cabling Installation

• In each store where new structured cabling is required, the scope of works will be as follows:
  
  · Run up to 6 new CAT7 FFTP cables to new or existing oven location.
  
  · Seal and fireproof any walls where cables have been run through
  
  · Feed cables down existing trunking were installed. If no trunking exists, it must be provided and installed by the installers, running down the wall, terminating withing easy cable reach of the oven if not located directly behind the oven. All works undertaken must meet LIDL standards.
  
  · Installers to provide additional trunking in managers office if required
  
  · Installers to provide all materials required, including 50mm back boxes, CAT7 termination ports, CAT7 FFTP cable, trunking and all network modules at both ends of network cable.
  
  · Each port to be FLUKE tested and report created.
  
  · To attach a cat 6a network patch lead between new network port and oven, and between patch panel and switch. Please check Patching above for port details.
  
  · Once verified working, attach supplied patch lead into the network socket and corresponding oven. On the patch Panel, ensure ALL corresponding ports are patched into the correct switch port as detailed below and test the connection.

• Picture of Oven Area - Total of 6 Data Points

  Media

• Picture of Outlet Labelling

  Media

• Picture of Ovens Patched to Data Outlets

  Media

• Picture of Rack Patching - Ensure Cables tracing is visible from picture

  Media

• Picture of Each Switch port patched with activity light showing

  Media

• Description of Works Completed - New Cables, Replace Terminations, Replace Faceplates etc....

• Image of Oven area once completed

  Media

Comments/Snags (if any)

• Are there any Installation Snags?:

  Yes

  No

• Snag?

Installation Sign-Off:

• LMF

  Media

• Store Contact (CAPITALS):

  Sign

• Lead Engineer (CAPITALS):

  Sign

• Installation Finish Date:

  Date