Plumbing Commissioning Checklist

• Project Name

• Location
  Address

• Project Manager

• Date Inspected

  Date

General

• Is the work area clean, orderly, no leftover material or debris?

  Yes

  No

  N/A

• Are Safety Hazards addressed: sharp edges, low head clearance, missing equipment guards, etc.?

  Yes

  No

  N/A

• Are Maximo Tag, Nameplate, and Serial Number attached to equipment?

  Yes

  No

  N/A

• Is instrument gauges/meters labeling correct and operating in the normal range?

  Yes

  No

  N/A

• Are valves labeled according to standard?

  Yes

  No

  N/A

• Are equipment and components labeled according to labeling standard?

  Yes

  No

  N/A

• Are wall and ceiling penetrations repaired, painted, or replaced with equivalent material?

  Yes

  No

  N/A

• Has penetrations through fire rated construction been sealed with fire caulk and pillows?

  Yes

  No

  N/A

• Does the installation meet code compliance requirements?

  Yes

  No

  N/A

• Do isolation devices (valves, disconnects, etc.) have provisions for lock-out devices?

  Yes

  No

  N/A

• Has material been disposed or recycled in the proper containers (Ex: Wood, Metal, General Trash, Cardboard)?

  Yes

  No

  N/A

• Has abandoned, unused, or decommissioned equipment been wrecked out or removed from service (Note: Apply Red Tag, if applicable)?

  Yes

  No

  N/A

• Are manufacturer installation, operation, and start-up documents complete and verified?

  Yes

  No

  N/A

• Does equipment meet requirements for workspace clearance (Ex. Electrical panels, thermostats, etc.)?

  Yes

  No

  N/A

Documentation

• Are equipment operation manuals and specifications submitted to the System Owner?

  Yes

  No

  N/A

• Are as-built documentation, such as red line drawings, are submitted to the System Owner?

  Yes

  No

  N/A

• Have LOTO procedures been documented for nonstandard or special electrical, mechanical, and chemical systems which will be needed for future use?

  Yes

  No

  N/A

Plumbing

• Are all new piping tie-ins to existing plumbing mains and submains coordinated with system owner for capacity and compatibility?

  Yes

  No

  N/A

• Are pipes labeled in compliance to the current Standard, including direction of flow and content?

  Yes

  No

  N/A

• Are dielectric unions on dissimilar metals installed where applicable?

  Yes

  No

  N/A

• Is chilled water piping, both supply and return, insulated per design?

  Yes

  No

  N/A

• Are rains sized properly, in proper location, and traps installed per design?

  Yes

  No

  N/A

• Is all gravity drain piping sloped a minimum of 1/8" drop per linear ft or greater as required by system capacity and building code?

  Yes

  No

  N/A

• Are plumbing fixtures vented to correct location with properly sized vent line as required?

  Yes

  No

  N/A

• Does the supply water piping include the properly sized water arrestor?

  Yes

  No

  N/A

• Are new chilled water piping systems chemically passivated per current Standards

  Yes

  No

  N/A

• Are all pipe weldments made with sil-fos, unless otherwise approved by system owner?

  Yes

  No

  N/A

• Does the system meet performance design criteria for operation and control (temperature, end of line pressure, flow rates, test and balance, etc.)?

  Yes

  No

  N/A

• Is the pipe properly supported?

  Yes

  No

  N/A

• Are Aerators/Strainers in place and clean?

  Yes

  No

  N/A

• Are faucet/flush handles secured and properly aligned?

  Yes

  No

  N/A

• Are joints between fixtures and walls, floors, and counters sealed?

  Yes

  No

  N/A

• Are fixtures installed consistent with ADA and Code requirements?

  Yes

  No

  N/A

• Are any additional commissioning checklist(s) complete, if applicable?

  Yes

  No

  N/A

Completion

• Additional Comments

• Inspected by:

  Sign

• Approved by:

  Sign