Pull Out Testing Manbre Wharf

• Site conducted

  Manbre Wharf

• Document Reference

• Conducted on

  Date

• Prepared by

  Anca-Diana Radu

  Dan Radu

• Pack

  Select Pack 01 Pack 02 Pack 03 Pack 04 Pack 05 Pack 06 Pack 07 Pack 08 Pack 09 Pack 10 Pack 11 Pack 12 Pack 13 Pack 14 Pack 15 Pack 16

  • Pack 01
  • Pack 02
  • Pack 03
  • Pack 04
  • Pack 05
  • Pack 06
  • Pack 07
  • Pack 08
  • Pack 09
  • Pack 10
  • Pack 11
  • Pack 12
  • Pack 13
  • Pack 14
  • Pack 15
  • Pack 16

• Level

  Select 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57

• Drawing reference

  Media

• Location

  Select North South West East All Elevations

  • North
  • South
  • West
  • East
  • All Elevations

• Description

  Select Curtain Wall base fixing

  • Curtain Wall base fixing

• Type of Fixing Tested

  Anchor Bolt

  Resin

  Through bolt

• What kN value to be tested?

• What type of fixing's used

• Diameter of fixings

• Base material

  Concrete

  Concrete New building

  Concrete Old building

• Detail reference

  Media

Signatures

Essex Cladding Qa

• Name/Signature

  Drawing

• Date

  Date

EAG representative

• Name/Signature

  Drawing

• Date

  Date

• Has the method statement been explained and understood?

  Yes

  No

  N/A

• Hydra-jaws testing rig set up correctly and levelled over fixing.<br>Adapter inserted into the testing ring & securely connected to the fixing. <br>

  Yes

  No

  N/A

• Ensure rig and puller is plumb/levelled over the bolt.

  Yes

  No

  N/A

• Hold point inspection (check equipment is set up correctly).

  Yes

  No

  N/A

• Set load indicator dial to test load of required kN and start applying pulling force until the needle reaches the pre-set indicator marker<br>Leave for a total of 1 minute and monitor.<br>

  Yes

  No

  N/A

• Check after 1 minute if load applied has dropped (a loss factor 5% of total load applied acceptable i.e. 1.0KN)

  Yes

  No

  N/A

• Any signs of concrete breakage around the bolt.

  Yes

  No

  N/A

• PASS…

  Yes

  No

  N/A

• Photo record made. Photos have to be attached to this completed form.

  Media

• Comments/Remarks