Site-Inspection

• Site Name

• Conducted on

  Date

• Prepared by

• Location
  Address

• SWARCO Inspector:

• Date:

  Date

• SWARCO Personnel:

• Subcontractors:

• Client:

• Yes

  No

  N/A

Intake Equipment:

• Is the service cable in good condition?

  Yes

  No

  N/A

• Is the service cable adequately supported?

  Yes

  No

  N/A

• Is the fuse carrier & Meter sealed?

  Yes

  No

  N/A

• Is the service head in good condition?

  Yes

  No

  N/A

• Are the meter tails adequately supported?

  Yes

  No

  N/A

• Are the meter tails less than 3m long?

  Yes

  No

  N/A

• Are the tales protected solely via the DNO Fuses

  Yes

  No

  N/A

Solar PV:

• Isolator present to isolate PV from public supply?

  Yes

  No

  N/A

• Warning label to show 2 sources of supply?

  Yes

  No

  N/A

• Are the AC & DC isolators in good condition?

  Yes

  No

  N/A

• Is there a single-line diagram showing the installation?

  Yes

  No

  N/A

• Are all cables correctly supported?

  Yes

  No

  N/A

TT / Earthing:

• Is the earthing conductor suitable? (Copper Rod / Tape)

  Yes

  No

  N/A

• Is the termination to earth electrode protected against corrosion?

  Yes

  No

  N/A

• Is the termination to earth electrode reliably secured?

  Yes

  No

  N/A

• Is TT Earthing Required for this install?

  Yes

  No

  N/A

• Is the earthing connection label fitted at the electrode?

  Yes

  No

  N/A

• Is the earthing connection label fitted at the MET?

  Yes

  No

  N/A

• Is the earthing connection label fitted at cross-bonding locations?

  Yes

  No

  N/A

• Is the MET / Earth bar in good condition?

  Yes

  No

  N/A

Feeder Pillar:

• Is the consumer unit fixed correctly?

  Yes

  No

  N/A

• Is the lid to the consumer unit fitted correctly?

  Yes

  No

  N/A

• Are all the blanks fitted?

  Yes

  No

  N/A

• Is the top of the consumer unit rated to IP4X?

  Yes

  No

  N/A

• Is the side & bottom of the consumer unit rated to IP2X?

  Yes

  No

  N/A

• Are rubber closed grommets used? Can they be removed to allow access to live parts without the use of a tool?

  Yes

  No

  N/A

• Are the blanks fitted tight and correctly fitted?

  Yes

  No

  N/A

• Is the consumer unit in good condition?

  Yes

  No

  N/A

• Does the RCD trip when the test button is used?

  Yes

  No

  N/A

• Are the circuits correctly labelled?

  Yes

  No

  N/A

• Is the RCD Test notice present?

  Yes

  No

  N/A

• Is the next inspection label present?

  Yes

  No

  N/A

• Is there a Circuit schedule?

  Yes

  No

  N/A

• Are the cable ducts sealed to prevent rodent entry?

  Yes

  No

  N/A

• Is the feeder pillar locked?

  Yes

  No

  N/A

Chargers:

• Are the chargers correctly fixed?

  Yes

  No

  N/A

• Are the chargers Level?

  Yes

  No

  N/A

• Are the chargers operational?

  Yes

  No

  N/A

• Are the chargers in good condition?

  Yes

  No

  N/A

• Are the chargers identified?

  Yes

  No

  N/A

• Are Barriers / Wheel stops installed?

  Yes

  No

  N/A

• Are the chargers accessible?

  Yes

  No

  N/A

Car Park:

• Is the area clear from construction debris?

  Yes

  No

  N/A

• Are the bay lines installed?

  Yes

  No

  N/A

• Are the spaces the correct size?

  Yes

  No

  N/A

• Is the tarmac/concrete from trenching level with the finished surface?

  Yes

  No

  N/A

• Is all signage installed?

  Yes

  No

  N/A

Touch Potential (Not required if o-pen device is used)

• Is any street furniture located within 2m of the charger? (fed via another power source than the charger)

  Yes

  No

  N/A

• Is any street furniture located within 2m of the Feeder Pillar? (fed via another power source than the charger)

  Yes

  No

  N/A

• Is any street furniture located within 2m of the EV whilst on charge? (fed via another power source than the charger)

  Yes

  No

  N/A

• Are there any other exposed conductive parts or extraneous conductive parts within 2m of the charger?

  Yes

  No

  N/A

• Are there any other exposed conductive parts or extraneous conductive parts within 2m of the Feeder Pillar?

  Yes

  No

  N/A

• Are there any other exposed conductive parts or extraneous conductive parts within 2m of the EV Whilst on Charge?

  Yes

  No

  N/A

Site Photos

• Photo of whole install

  Media

• Photo inside of feeder pillar

  Media

• Photo inside charger (Showing connections)

  Media

• Photo inside DB

  Media

• Photo of Signage

  Media

Certification

• Has the correct certificate been provided? (EIC / Minor Works)

  Yes

  No

  N/A

• Is the Client & Site address correct?

  Yes

  No

  N/A

• Is the correct installation listed E.G. 2 X Raption 150s (Not 2 X EV Chargers)

  Yes

  No

  N/A

• is the correct new installation/addition to the existing install listed?

  Yes

  No

  N/A

• Is the Regulation amendment date correct on the certificate?

  Yes

  No

  N/A

• is the correct earthing system ticked?

  Yes

  No

  N/A

• is the nature of the supply parameters & protective device completed in full? (No N/A should be listed in any of these boxes)

  Yes

  No

  N/A

• Is the maximum demand listed?

  Yes

  No

  N/A

• is the main protective conductors completed correctly?

  Yes

  No

  N/A

• Are the R1+R2 readings calculated? These should not be calculated unless cables are installed within a DSEAR / ATEX area:<br><br>The R1+R2 should be around the calculated figure but are unlikely to all be the exact calculated figure, to calculate the figure find the ZE of the site (normally on page 1 within the supply details section) then<br>minus the ZS value of the circuit, normally shown on the 4th box from the right on the results page. ZE‐ZS= R1+R2.

  Yes

  No

  N/A

• Are all signatures correct?

  Yes

  No

  N/A

• Are all test results correct & comply with BS7671

  Yes

  No

  N/A

• Yes

  No

  N/A

Signed:

• Date:

  Date