Ventia Safety - SPS Safety Grille Load Test Assessment

• The version control will be maintained by the SHEQ team and is controlled via the Safety Equipment Inspections Document 2073838157-15.

• Station No.

• Document No.

• Conducted on

  Date

• Prepared by

• Location
  Address

• Personnel

The version control will be maintained by the SHEQ team and is controlled via the Safety Equipment Inspections Document 2073838157-15.

Load Testing Information

• Safety Grille Load Test Measurement Drawing

  

• Add Hatch for multiple Access Hatches

Hatch

Access Hatch

• Hatch No

Hatch Frame

• Supports Design

  Corner Supports

  Side Support

  Surrounding Edge Support

• No of Supports

  1

  2

  3

  4

• In case of Side Supports used - Note down dimensions (Width x Depth x Thickness) mm

Safety Grille

• Safety Grille dimension (Hinge Side X Adjacent Side) mm

• Safety Grille Grid Design

  Bar Mesh

  Unidirectional Bar

  Non - standard Design

• Grid Bar Dia (mm)

• Grid Bar Spacing- Each Way (mm X mm) or Unidirectional Bar (mm apart)

• Edge Frame

  Flat Bar

  Angle Bar

  Round Bar

  No Frame

• Edge Frame Dimensions - Flat Bar (Width x Depth) mm or Angle Bar (Width x Depth x Thickness) mm

• Stiffeners

  Angle Bar

  Flat Bar

  No Stiffeners

• Stiffeners Dimensions - Angle Bar (Width x Depth x Thickness) mm or Flat Bar (Width x Depth) mm

• Comments

Safety Grille Photos

• Take a Photo Before Load Test

  Media

• Take Photo/s When Full Load Applied

  Media

• Take a Photo After Load Test

  Media

Measurements

• Download Measurement Table Image from Gallery and Record measurements on it. (Refer to the Safety Grille Load Test Measurement Drawing to Record Right Information)

  Media

Status After Load Test

• Safety Grille

  Safe

  At Risk

  N/A

• Supports

  Safe

  At Risk

  N/A

• Hinges & Bolts

  Safe

  At Risk

  N/A

Classification

• Classification After Inspection

  Acceptable

  Unacceptable- Remediation Required

  Unacceptable- Replacement Required

• Priority

  Select Not Applicable 1 (Time Frame - 6 weeks) 2 (Time Frame - 5 weeks) 3 (Time Frame - 4 weeks) 4 (Time Frame - 3 weeks) 5 (Time Frame - 2 weeks) 6 ( Act Immediately)

  • Not Applicable
  • 1 (Time Frame - 6 weeks)
  • 2 (Time Frame - 5 weeks)
  • 3 (Time Frame - 4 weeks)
  • 4 (Time Frame - 3 weeks)
  • 5 (Time Frame - 2 weeks)
  • 6 ( Act Immediately)

Work Scope

• Complete Assembly

  Select Replace complete assembly- Downturn Design (DTC 3300) (Stainless Steel 316 grade) Replace complete assembly- Upturn Design (DTC 4406, 4407) (Stainless Steel 316 grade) Replace/Repair Sign (Confined Space) Replace/Repair Sign (Hazardous Gasses)

  • Replace complete assembly- Downturn Design (DTC 3300) (Stainless Steel 316 grade)
  • Replace complete assembly- Upturn Design (DTC 4406, 4407) (Stainless Steel 316 grade)
  • Replace/Repair Sign (Confined Space)
  • Replace/Repair Sign (Hazardous Gasses)

• Hatch Cover

  Select Replace Cover (Aluminium) Replace or Repair Hinge Replace or Repair Locking Cleat Replace or Repair Lifting Handle Replace Hinge Bolts & Nuts (Galvanised) Replace Hinge Bolts & Nuts (Stainless Steel) Remove rust & re-coat with cold Galv paint Install New Rubber Beading

  • Replace Cover (Aluminium)
  • Replace or Repair Hinge
  • Replace or Repair Locking Cleat
  • Replace or Repair Lifting Handle
  • Replace Hinge Bolts & Nuts (Galvanised)
  • Replace Hinge Bolts & Nuts (Stainless Steel)
  • Remove rust & re-coat with cold Galv paint
  • Install New Rubber Beading

• Hatch Frame

  Select Replace Frame (Galvanised) Replace Frame (Stainless Steel) Remove existing supports Add 2 corner supports at Hinge end Add 2 corner supports opposite to Hinge end Add 4 corner supports Add 2 Side supports at Hinge end Add 2 Side supports opposite to Hinge end Remove rust & re-coat with cold Galv paint

  • Replace Frame (Galvanised)
  • Replace Frame (Stainless Steel)
  • Remove existing supports
  • Add 2 corner supports at Hinge end
  • Add 2 corner supports opposite to Hinge end
  • Add 4 corner supports
  • Add 2 Side supports at Hinge end
  • Add 2 Side supports opposite to Hinge end
  • Remove rust & re-coat with cold Galv paint

• Safety Grille

  Select Replace Grille (Galvanised) Replace Grille (Stainless Steel) Install flat bar edge frame lnstall angle bar edge frame Repair or Replace Stiffeners Add stiffeners Repair opening in grille Repair or Replace Hinge Replace Hinge Bolts & Nuts (Galvanised) Replace Hinge Bolts & Nuts (Stainless Steel) Repair or Replace lifting handles Remove rust & re-coat with cold Galv paint

  • Replace Grille (Galvanised)
  • Replace Grille (Stainless Steel)
  • Install flat bar edge frame
  • lnstall angle bar edge frame
  • Repair or Replace Stiffeners
  • Add stiffeners
  • Repair opening in grille
  • Repair or Replace Hinge
  • Replace Hinge Bolts & Nuts (Galvanised)
  • Replace Hinge Bolts & Nuts (Stainless Steel)
  • Repair or Replace lifting handles
  • Remove rust & re-coat with cold Galv paint

• Comments

• Sign

  Sign