Title Page
-
Conducted on
-
Prepared by
-
VIN: SE4MA0002PH000 _ _ _
-
Key Number
Order Audit
-
Vehicle Identification Number (VIN) - matches the order (sticker + stamp | Le3 \ only stamp | Le1))
-
Mudguards type - matches the order
-
Seat colour - matches the order
Mechanical, Functional and Visual Inspeciton
Headlight
-
Low Beam
-
High Beam
Rear Light Functions
-
Rear Light
-
Number Plate Light - needs to point downwards
-
Front Brake Light
-
Rear Brake Light
Indicators
-
Connection and Lens Orientation
Horn
-
Sound
Lockset
-
Steering Lock Operation
Brakes
-
Fluid Level - L/H Master Cylinder (above the minimum level + visible air bubble)
-
Fluid Level - R/H Master Cylinder (above the minimum level + visible air bubble)
-
All Brake Hoses - No Evidence of Leaking Fluid
-
CBS - Bite Point Distance (using force gauge and the lever position gauge - 90Nm needs to be achieved)
-
Required Force Achieved?
-
Front Brake - Bite Point Distance (using force gauge and the lever position gauge - 90Nm needs to be achieved)
-
Required Force Achieved?
Brake Hoses
-
Front Brake Bottom Hoses - No contact with Mudguard Stay, Mudguard, Front Caliper, Forks or Spokes.
-
Twin clip - position
Battery Housing
-
DBCU Cover fitted (bolts sitting flush)
-
OBD - reconnected
-
3M Housing Supporting Tape - evident
-
Magnet Orientation - R/H Cover
-
Sensor and Spacer Orientation
-
R/H Cover - no resistance evident when closing prior to latching
-
R/H Cover - Front edge ribs aligned prior to latching
-
Latch Mechanism - Finger force sufficient to achieve latching with no battery inside
-
Battery Housing Profile Fit - Moulding flush with the cover
-
Battery Housing Profile Fit - Gap between the cover and housing to be even around the whole profile (1.8 mm maximum)
-
Primary Battery - smooth removal and installation
Switches (Require the Primary Battery)
-
Operation of 'I' / 'D' / 'N' control buttons
Safety Lockout System
-
Sidestand Safety Lockout - functionality
-
Battery Housing Door Safety Lockout - Ignition on
-
Battery Housing Door Safety Lockout - Not Latched in 'Drive'
Side Stand
-
Operation
-
Sidestand switch distance - within 2.5mm (use PT000409)
Suspension
-
Rear Suspension Preload - set to the middle
-
Rear Suspension - no contact between RSU and stays
-
Rear Suspension - smooth operation (compress and release with no evident noises)
-
Front Bearings - smooth operation
Handlebar
-
No gap between the grips and switchcubes
-
Dots aligned to Switchcubes and Handlebar Clamp
-
Reservoir Caps / Master Cylinders Clamp - orientation
Wheels
-
Spoke Tension (0 pass / 1-3 repair / 4+ wheel changed)
-
Front Wheel Axle - no gap between fork's face and axle's head
-
Rims Quality - cosmetic appearance
Details
-
Loose or missing bolts / washers (Brake Calipers, Battery Retention, Latch Mechanism, Conduit, Yokes)
-
VIN Stamp - Lacquer applied and correct alignment within the box boundaries
-
APS bolts - replaced (retaining clamp pointing upwards)
-
Side Reflectors - orientation
-
Rear Reflector - orientation
-
Protection Tape - applied in the correct position on Conduit
-
Torque Paint - Top Yoke Nut | Swing Arm | Hub Motor Axle Nuts
-
Front Grills - No sharp edges evident
Visual Appearance
-
Mudguards (satin black, silver or carbon expected at this stage) - Paint Quality
-
Other Elements - Paint Quality
-
Brushed Metalwork Quality – no scratches or staining
-
Controller Casing - Finish Quality
-
Nut Covers - applied on wheels axles' nuts and bolt heads
Other
-
Do you have any remarks to add?
Release to stock
-
Please put a tag on
-
Please disconnect the 12V battery
