Title Page

  • Document No.

  • Audit Title

  • Client / Site

  • Conducted on

  • Prepared by

  • Location
  • Personnel

  • • Confirm house elevation and all options.

  • • Check all walls for square and plumb.

  • • Check all walls for bowed studs. Pay close attention to the cabinet and shadow box areas.

  • • Check all load bearing headers for #2 2x10”s and LVL’s per plan and nailed per design/code.

  • • Check TGI floor design drawing and ensure that no holes or notches are cut into the TGI’s.

  • • Ensure that all roof and floor hangers are nailed properly and glued using subfloor adhesive.

  • • Check that all subfloor decking is glued, screwed, and nailed with ring shank nails.

  • • All sill plates should be secured with 3” screws or concrete straps/bolts as required by local building codes.

  • • Mark all door sizes and swings and check R.O.

  • • Confirm all opening header heights are 7’ 10”

  • • Mark all sheetrock wrapped openings.

  • • Install temp. rails at all stairs and balconies.

  • • Ensure all stairs are properly supported and a moisture barrier installed if the stair contacts concrete.

  • • Ensure that each roof truss has a hurricane clip, is braced and is aligned with a stud below.

  • • Check each truss for missing or damaged gusset plates.

  • • Ensure that all OSB is gapped and plywood clips are utilized on the roof sheathing.

  • • Ensure that the attic platform is raised 9” and decked with ¾” subflooring with a walkway to the attic stairs.

  • • Check that all non-load bearing walls are 24” O.C.

  • • Check for OSB in all chase tops.

  • • Ranch and 2nd floor framing to be 24” O.C.

  • • 1st floor framing and cabinet wall framing to be 16” O.C.

  • • 3 story Basement framing to be 2x6 16” O.C.

  • • Ensure garage door framing is done per details and per local code requirements.

  • • Ensure all 6” walls are framed per plan.

  • • Install tub studs at all showers and tub edges.

  • • Check that hangers are installed at P.D.S.

  • • Verify open rail and knee wall conditions and block as req. confirm height

  • • Mark all sink, toilet, tub, dishwasher, and water heater locations.

  • • Mark all flooring change locations.

  • • Mark all elevation material changes.

  • • Ensure that all loads are transferred to the slab/footing.

  • • Check the rough opening sizes/locations of all doors, windows and overhead garage doors.

  • • confirm a whole load bearing walls, headers, and structural details

  • • Ensure that T-Ply and insulation is installed behind

  • • Install 2x4 band at tubs, showers, and any exterior wall area not accessible.

  • • Check that all sheathing is nailed per code.

  • • Make sure all stairs have a min 6’-8” headroom.

  • • Confirm Office has scheduled all undergrounds

  • • Check truss bracing

  • • Confirm Water meter is set

  • • Check toilet locations center of water closet 15 1/2 inches off of wall 15 inches off of the cabinet and tub and no joists below

  • • Check all Joists for damage

  • • Place all updated cut sheets and options in windows

  • Visual Documentation

  • Notes

  • Builder/Superintendent Signature

The templates available in our Public Library have been created by our customers and employees to help get you started using SafetyCulture's solutions. The templates are intended to be used as hypothetical examples only and should not be used as a substitute for professional advice. You should seek your own professional advice to determine if the use of a template is permissible in your workplace or jurisdiction. You should independently determine whether the template is suitable for your circumstances.