Switch Board Post Energisation Check Sheet

• Site

  Select

• Document No.

• Job Number

  109

• Client

  Synergy

• Date

  Date

• Prepared by

Visual Inspection prior to energisation. Please add photos to each question where practicable.

• Inspect switchboard for damage. Is switchboard in good condition?

  Yes

  No

  N/A

• Please describe issue. Add photos

• Are all escutcheons/covers present and in good condition?

  Yes

  No

  N/A

• Please describe issue. Add photos.

• Is there adequete protection to ensure live parts cannot be accessed through covers/escutcheons

  Yes

  No

  N/A

• Please describe issue. Add photos.

• Has there been any changes to the switch board since last tested?

  Yes

  No

• Please describe issue. Add photos.

• Are all cable connections correct? Right locations? Correct phasing?

  Yes

  No

  N/A

• Please describe issue. Add photos.

• Is the switch board fit for energisation?

  Yes

  No

  N/A

• Please describe issue. Add photos.

Testing

• Meter used in tests. Add photo of meter and calibration cert/sticker

  Fluke 1663 HEC162

  Metrel MI3250 HEC121

  Kyoritsu KEW3125A HEC122

Measure voltage at SPD. Ensure all CBs, Main Switch and outgoing circuits are in the Off position before testing. Please investigate any abnormal readings.

• Neutral -Earth

• Red - Earth

• Red - Neutral

• Red - White

• Red - Blue

• White - Earth

• White - Neutral

• White - Blue

• Blue - Earth

• Blue - Neutral

Phase Rotation tests measured at SPD

• Phase rotation correct?

  Yes

  No

• Please describe issue

  Yes

  No

  N/A

Turn on SPD, conduct visual inspection

• Does WP meter come on?

  Yes

  No

• Please describe issue

Turn on Consumer Main Switch, conduct visual inspection

• Does REM Live Indicator come on? All lights working?

  Yes

  No

• Please describe issue

  Yes

  No

  N/A
Measure voltage at line side of Main CBs. Ensure SPD and Main Switch are on, all other CBs off. Test

• Please identify the CB under test

• Neutral - Earth

• Red - Earth

• Red - Neutral

• Red - White

• Red - Blue

• White - Earth

• White - Neutral

• White - Blue

• Blue - Earth

• Blue - Neutral

• Phase rotation correct?

  Yes

  No

• Please describe issue

Measure voltage at line side of RCDs & Small CBs. Turn on Light & Small Power Main CB. Ensure all RCDs and small CBs are turned off. Please investigate any abnormal readings. Test

• Please identify the CB under test

• Neutral-Earth

• Active -Earth

• Active - Neutral

RCD tests. Verify that all external devices are either switched off or plugged out as appropriate. Turn on Light & Small Power Main CB. Turn on all RCDs. Please investigate any abnormal readings. Test

• Please identify the CB under test.

• Record make, and model of RCD. Add a photo.

• Overcurrent rating and type of RCD (e.g.: C16, B10, D20, etc)

• Residual trip current in mA

• Fault rating in kA

• Does the RCD operate when the manual trip button is pressed?

  Yes

  No

• Please describe issue

• RCD trip time at 0 deg in milli seconds

• RCD trip time at 180 deg in milli seconds

• Verify isolation of all poles after RCD operates

  Pass

  Fail

  N/A

Circuit Breaker Settings. Verify settings with client engineer.

• Red Phase - Test fault loop impedence at SPD. Add photo of test result

• Red Phase - Record Prospective Short Circuit current from last test. Add photo of test result

• White Phase - Test fault loop impedence at SPD. Add photo of test result

• White Phase - Record Prospective Short Circuit current from last test. Add photo of test result

  Yes

  No

  N/A

• Blue Phase - Test fault loop impedence at SPD. Add photo of test result

• Blue Phase - Record Prospective Short Circuit current from last test. Add photo of test result

  Yes

  No

  N/A

• Q1 current setting

• Does Customer SPD grade with Western Power's upstream protection as noted on Western Power's SLD?

  Yes

  No

  N/A

• Verify that Short circuit/Instantaneous setting of Q1 is set lower than value of Prospective Short Circuit value as per our test results

  Yes

  No

  N/A

• Seal settings window of Q1 using copper strand and a bootlace. Set phone to datestamp and add photo of sealed settings

  Yes

  No

  N/A

• Q2 current setting

• Q3 current setting

• Q4 current setting (if applicable)

Close out. Leave all outgoing CBs in off position until ready to energise final circuits

• Comments (tagged, locked out, etc). Please note any works that are incomplete out in the field and ensure relevant CBs are locked/tagged out.

• Electrical Licence Number

• Sign off

  Sign