Wallbox Commissioning Report for DCF1, DCF2 & DCF4

• Customer

• Location
  Address

• Country

• Assigned Commissioner/Technician

• Start Time

  Date

Product

• Supernova Model

  Select DCF1 - 60 kW split charge DCF1 - 60 kW non-split charge DCF2 - 60 kW DCF2 - 120 kW DCF2 - 150 kW DCF4 - 220 kW

  • DCF1 - 60 kW split charge
  • DCF1 - 60 kW non-split charge
  • DCF2 - 60 kW
  • DCF2 - 120 kW
  • DCF2 - 150 kW
  • DCF4 - 220 kW

• Serial Number (S/N)

• Part Number (P/N)

• Has the installation information been reviewed prior to carrying out the work? (Geolocation, location pictures, supply cut points, specific security procedures, emergency procedures, existence of flammable/explosive gases).

  Yes

  No

• Do you have isolated tools, correct Personal Protection Equipment(PPE), LOTO locking kit and everything in good condition to carry out the job safely?

  Yes

  No

• Is the condition of the PPE correct: has the "blow test” been carried out on the dielectric gloves?

  Yes

  No

• Are the work area conditions adequate to guarantee your safety? (visibility, weather (rain, storm, strong winds, etc)

  Yes

  No

• IMPORTANT: check the conditions of the input cables in the charger. If they are not in good condition, STOP work.

  Good

  Fair

  Poor

  N/A

• External Overall Visual Inspection

  Good

  Fair

  Poor

• Will it require a further visit?

  Yes

  No

• Verify correct clearance around the charger

  Select DCF1: MINIMUM 70cm front, 40cm sides DCF2: MINIMUM 70cm front, 40cm sides, 100cm behind DCF4: MINIMUM 70cm front, 40cm sides, 100cm behind

  • DCF1: MINIMUM 70cm front, 40cm sides
  • DCF2: MINIMUM 70cm front, 40cm sides, 100cm behind
  • DCF4: MINIMUM 70cm front, 40cm sides, 100cm behind

• Verify presence of left door lock and keys

  Pass

  Fail

• Internal general visual inspection

  Good

  Fair

  Poor

• Verify correct anchorage to the floor

  Pass

  Fail

• Has the CMS been installed for the cables on both sides?

  Yes

  No

• Verify inlet power cable entry plate with grommets fitted

  Pass

  Fail

• Verify scupper covers closed / inlet cable cover or panel A cover is in place

  Pass

  Fail

• Verify the charger is free from any traces of condensation or water ingress

  Pass

  Fail

• Verify the weather stripping seal in all 3 doors

  Pass

  Fail

• Quantity of Power Modules installed

• Check correct closure of all doors

  Pass

  Fail

• Has this been rectified?

  Yes

  No

• Verify the presence of air filters on each side

  Yes

  No

• Front door sensor position check

  Pass

  Fail

• Front door rod guide check

  Pass

  Fail

• EV gun stickers installed?

  Yes

  No

DCF1 Specific check

• Check QPM / back planes / copper bars

  Pass

  Fail

• Has this been rectified?

  Yes

  No

Additional issues/comments

• Additional issues/comments

DCF2 Specific check

• Verify that Panel A protective rubber strip is present

  Yes

  No

• Check all DC cables (from DC bus bar to DC contactor) for damage/cuts

  Pass

  Fail

• Verify correct connection of input cables (L1-L2-L3-N-PE)

  Pass

  Fail

• Has this been corrected?

  Yes

  No

• Check the input cable section meets local & installation requirements

  Pass

  Fail

• Verify tightness and connection of all internal cables

  Pass

  Fail

• Has this been corrected?

  Yes

  No

• Verify the presence of protections in main breaker panel

  Select MCB RCD SPD Fuse Other

  • MCB
  • RCD
  • SPD
  • Fuse
  • Other

• Are the main power cables in the correct order?

  Yes

  No

• Has this been rectified?

  Yes

  No

• Are Supernova's main switch and protections OFF?

  Yes

  No

• Turn on external main breaker

• Has voltage been verified? (values to be provided on next page)

  Yes

  No

• Turn on internal protections

• Turn on Supernova main switch

• Input AC Voltage: L1-L2 (400V +/- 10%)

• Input AC Voltage: L1-L3 (400V +/- 10%)

• Input AC Voltage: L1-N (230V +/- 10%)

• Input AC Voltage: L1-Earth (230V +/- 10%)

• Input AC Voltage: L2-L3 (400V +/- 10%)

• Input AC Voltage: L2-N (230V +/- 10%)

• Input AC Voltage: L2-Earth (230V +/- 10%)

• Input AC Voltage: L3-N (230V +/- 10%)

• Input AC Voltage: L3-Earth (230V +/- 10%)

• AC Voltage: Earth - Neutral (+/- 0V)

• Software version on arrival (Factory SW version)

• Updated Software Version

• Verify correct functionality of the 3 door sensors

  Pass

  Fail

• Check HMI functionality

  Pass

  Fail

• Has this been rectified?

  Yes

  No

• Verify RFID reader functionality

  Pass

  Fail

• Has this been rectified?

  Yes

  No

• Verify beacon, holster & courtesy lights functionality

  Pass

  Fail

• Has this been rectified?

  Yes

  No

• Verify cooling fans functionality and noise

  Pass

  Fail

• Has this been rectified?

  Yes

  No

• AC meter configuration checked?

  Yes

  No

• Was AC meter configuration correct?

  Yes

  No

• Has this been rectified?

  Yes

  No

• Bender isometers configuration checked?

  Yes

  No

• Were both Benders configured correctly? (or 1 in the case of DCF1 SN60)

  Yes

  No

• Has this been rectified?

  Yes

  No

• Trafox meter configuration checked? (DCF2 only)

  Yes

  No

• Was Trafox configuration correct? (DCF2 only)

  Yes

  No

• Has this been rectified?

  Yes

  No

• Point of Sale installed?

  Yes

  No

• Brand:

  Wallbox provided Payter P66

  Wallbox provided Payter Apollo

  CPO supplied POS

  N/A

• Brand and model:

• Payter SIM & SAM cards fitted?

  Yes

  No

  N/A

• Can the POS be verified as working correctly?

  Pass

  Fail

  N/A

• Wallbox telemetry connected

  Pass

  Fail

• OCPP Connection method

  Teltonika

  Ethernet

  Teldat

• Model

  TRB140

  RUT241

  RUT901

• Configured from factory?

  Yes

  No

• Have you configured it?

  Yes

  No

• Which configuration (.tar) file has been used?

• Was it configured correctly?

  Yes

  No

• Which configuration (.tar) file has been used?

• Configured

  Yes

  No

• Signal strength (in dBm)

EV test

• Type of charging test

  EV

  COMEMSO

• Brand & model of EV(s) used

• Charging session - Hose 1 <br>

  Pass

  Fail

  N/A

• Charging session - Hose 2

  Pass

  Fail

  N/A

• Split charge test (where possible)

  Pass

  Fail

  N/A

• Charger left powered on?

  Yes

  No

• Authorisation method

  OCPP

  Free Vend

• CPO URL and Charger ID

  Media

• Has the connection with the client backend been validated?

  Yes

  No

• Web Manager power limit set

• Add photos showing Supernova location

  Media

• Add photos showing Supernova interior and exterior (Front, left and right side)

  Media

• Add photo of sticker on the back of router

  Media

• Add photos of the breaker panel and location

  Media

• Commissioning validated by Wallbox DC Support? <br>+34 950 72 00 29 Global support / +61 2 9129 8353 Oceania support

  Yes

  No

• OCPP connectivity also validated by Wallbox DC Support?

  Yes

  No

  N/A

• Call Wallbox DC Support before leaving site

  Done

  Not done

• OCPP connectivity also validated by Wallbox DC Support?

  Yes

  No

• Additional comments

• Customer signature

  Sign

• Wallbox Commissioner/Technician signature

  Sign

• Wallbox certification ID number (found on your training certificate)