Title Page

  • Site conducted

  • Student Name

  • Assessment Method

  • Conducted on

  • Prepared by

  • Location
  • Job description

Be able to confirm safety of the system and equipment prior to completion of inspection, testing and commissioning in accordance with statutory and non-statutory regulations. LEARNING OBJECTIVE 1 <br>

Health & Safety checks- which of the following are to be implemented during this job LO1.1/1.2/1.3/2.1

  • Safe isolation

  • Permit to work

  • Method Statement

  • Risk Assessment

  • Check Suitable Earthing In Place

  • Check to conform mechanical soundness

  • Check to confirm suitability of equipment

  • Procedures in place for reporting unsafe conditions

  • Calibration certificates in place /checked

Be able to inspect electrical systems and equipment <br>LEARNING OBJECTIVE 2

Carry out a visual inspection in accordance with the requirements of the installation specification, the IET Wiring Regulations and IET Guidance Note 3 LO2.2

  • Details of visual inspection.

What Paperwork was completed 2.3/3.4

  • Schedule of inspections

  • Schedule of rest results

  • Electrical test certificates

  • Minor works certificate

Be able to test and commission electrical systems and equipment <br>LEARNING OBJECTIVE 3

Which out of the following tests have been performed in accordance with the requirements of the installation specification, BS 7671 and manufacturers’ instructions? (Assess minimum of two on two separate occasions.)

  • Visual Inspection

  • Continuity of CPC

  • Continuity of RFC

  • Insulation resistance

  • Polarity

  • Earth fault loop impedence

  • RCD/RCBO test

  • Prospective fault current

  • Functional testing

Relevant persons notified LO 3.3

  • Customers

  • Clients

  • Colleagues

  • Other contractors

  • Supervisors

Handing electrical systems over to relevant persons including documentation and demonstrating to the client the correct operation of the systems, equipment and components. LO 3.5, 3.6

  • Which procedures did you follow during the handover process?

  • Was the client satisfied with the work carried out.

Behaviour's and Feedback

The behaviours below are embedded into the performance units in this workplace logbook. These behaviours are part of the apprenticeship, and an expert witness and/or your assessor will also assess you against them. They will record and give feedback on your performance against these behaviours.

  • Behaviour 1 (B1): Works reliably and effectively without close supervision

  • Behaviour 2 (B2): Accepts responsibility for the work of themselves and others

  • Behaviour 3 (B3): Accepts, allocates and supervises technical and other tasks

  • Behaviour 4 (B4): Uses oral, written and electronic methods for the communication of technical and other information

  • Behaviour 5 (B5): Works effectively with colleagues, other trades, clients, suppliers and the public

  • Behaviour 6 (B6): Undertakes work in a way that contributes to sustainable development

  • Behaviour 7 (B7): Maintains and enhances competence in own area

  • Behaviour 8 (B8): Exercises responsibilities in an ethical manner

Assessor and Expert Witness Feedback

  • Assessor Feedback

  • Expert Witness Feedback

Completed

Student Signature

  • By the act of making this submission I am declaring that this is all my own work and that: • The work has not, in whole or in part, been knowingly submitted elsewhere for assessment • Where the submission includes work from a previous assessment this has been identified • Where materials have been used from other sources it has been properly acknowledged • If this statement is untrue, I acknowledge that an assessment offence has been committed Attention is drawn to the plagiarism, collusion and cheating policies of both the centre and of the awarding body. Proven incidents of plagiarism, collusion or cheating can result in a student being withdrawn from a qualification. I confirm that I have read and understood the above statements on plagiarism and collusion. I confirm that I have not committed plagiarism when completing the work contained in this evidence, nor have I colluded with another student in the preparation and production of this work. I am satisfied with the way the learning activity/Assessment(s) was conducted and with the outcome(s). I agree that the information provided here is an accurate account of what has taken place

Expert Witness Signature

  • As the expert witness I can confirm that all the work carried out in this unit has been done by the student named above under my supervision to the required standards.

Work Based Tutor Signature

  • I agree that the information provided here is an accurate account of what has taken place.

The templates available in our Public Library have been created by our customers and employees to help get you started using SafetyCulture's solutions. The templates are intended to be used as hypothetical examples only and should not be used as a substitute for professional advice. You should seek your own professional advice to determine if the use of a template is permissible in your workplace or jurisdiction. You should independently determine whether the template is suitable for your circumstances.