Title Page
-
Site conducted
-
Conducted on
-
Please select and move forward
-
Prepared by
-
Site ID
-
VUE Work Order Number
-
What is Outside Air Temp
-
What is the Delta T
-
Verify the unit thermostat is accurate, operating properly, and programmed to PNC set point schedule
-
Please add notes or action here
-
If unit is new or not listed in the assets list, please complete the PNC Retail HVAC Assessment - Survey Form NEW 1.2 as well
-
Unit Type
- Packaged AC
- Packaged HP
- Heat Pump
- Gas Pack
- Furnace
- Chiller
- Boiler
- Water Source HP
- Cooling Tower
- Other
-
Unit Name/# (for example, the second package unit would be named PKG-02)
-
Unit Location
- Roof
- Ground
- Mechanical Room
- Ceiling
- Basement
- Other
-
Inspect cabinet for signs of rust, wear or failure (provide comments)
-
Provide comments
-
Inspect all wiring and connections for tightness, signs if overheating, discoloration or compromise of wire insulation
-
Inspect for refrigerant and oil leaks
-
Does this unit have an economizer installed?
-
Inspect Mechanical linkages for wear, tightness, and clearances
-
Lubricate all motors and bearings if applicable
-
Straighten Condenser Coils
-
Clean Condenser coils with manufacturer recommended coil cleaner and rinse with water
-
Verify smooth operation of compressor and fans
-
Record rated and actual fan and compressor running amps
-
Are there any compressor 10 tons or larger?
-
Megger test compressor motor
-
Record suction and discharge pressures
-
Check and or test operation of high/low pressure safety devices. If none exist, please install if possible.
-
Is this unit equipped with Discharge and Supply air temperature sensors and control devices?
-
Verify operation of these sensors
-
Are all exhaust fans & HVAC return and supply grills clean of debri?
Evaporative/Blower Section
-
Straighten evaporator coils (up to 10% of the surface area)
-
Clean evaporator coils with coil cleaner made specifically for that purpose and rinse with water
-
Check fan cleanliness; inspect wheel, shaft and cage for wear and clearance
-
Check sheaves and pulleys for wear and alignment
-
Replace Belt an apply correct tension
-
Brush clean, vacuum or blow out evaporator coils. If needed clean with coil cleaner made specifically for that purpose and rinse with water.
-
Clean and flush evaporator drain pan, trap and drain line.
-
Is drain adequately sized?
-
Is drain properly sloped and supported?
-
Install pan tabs
-
Ensure TXV bulb is securely mounted and distributor tubes are protected from vibration and rubbing
-
Check motor starter if applicable
-
Replace air filter with MERV 8 filter or appropriate media
-
Write the date with permanent marker on filter frame. LEED BRANCHES REQUIRE MERV 13 FILTERS
-
Heat Pump?
-
Verify proper operation of reversing valve
-
Does unit have a Variable Frequency Drive?
-
Verify proper operation
-
Clean heat sink
-
Verify proper DC buss voltage
-
Are there VAV or Fan power units?
-
Inspect all wiring and connections for tightness, signs of overheating, wiring insulation compromised or discoloration
-
Check linkages for wear, tightness, and clearance
-
Verify fan cleanliness, inspect wheel, shaft and cage for wear and clearance
-
Verify sequence of operations as applicable
-
Verify operation of fan and motor
-
Verify valve/actuator operation
-
Check and record voltage and amp draw of resistive heating elements and compare with rating of the heater
-
Check and adjust controls, safeties, high limit switches etc. as needed
-
Replace air filter with MERV 8 filter
-
Write the date on filter frame in permanent marker. LEED branches require MERV 13 filters.
-
Does the site have any pumps that support HVAC operations?
-
Check for leaks on the pump and seals
-
Check inlet and outlet pressures
-
Ensure all drain and weeps are free and clear
-
Lubricate motor and pump bearing as required
-
Record rated amps and actual amp draw
-
Verify smooth operation of pump
-
Are there any Unit ventilators or Make up or air only units?
-
Inspect unit for cleanliness
-
Check dampers for wear, security. linkage adjustments
-
Clean condensate drain pan, P trap and drain
-
Inspect Fan cleanliness, inspect wheel, shaft and cage for wear and clearance
-
Check sheaves and pulleys for wear and alignment
-
Replace Belt
-
Check operation of fan switch
-
Check operation of low temperature safety device
-
Economizer and power exhausts, inspect linkages, motors, and seals calibrate as necessary
-
If unit is new or not listed in the assets list, please complete the PNC Retail HVAC Assessment - Survey Form NEW 1.2 as well
