Information
-
Project Name
-
Conducted on
-
Location
-
Field Supervisor
-
Project Manager
-
Prepared by
PERSONAL PROTECTIVE EQUIPMENT
-
All personnel wearing hard hats
-
Protective eyewear in use where required
-
Respiratory protection/breathing masks in use where required
EXTENSION CORDS
-
Plugged in to GFI receptacles
-
Minimum 14 gauge
-
Ground pin intact
-
Strain relief intact (no exposed wire at plug end)
-
Outer jacket intact
LADDERS
-
Extend 3' above walking surface or at least 4th rung from top
-
Secured to prevent displacement
-
All ladders in good condition
-
Extension ladders at proper 1:4 angle
-
All folding ladders used in fully open position only
-
Standing below top or first step down on step ladder
FALL PROTECTION
-
Fall protection in place at mezzanines, slab leave outs, elevator shafts, etc. <br>
-
Guardrail height 39-45” <br>
-
Guardrail able to withstand 200 lbs. of force <br>
-
Midrail height at 21” <br>
-
Toe boards installed <br>
-
Cable guardrails – less than 3” of movement <br>
WORKER PERSONAL FALL ARREST SYSTEMS (PFAS)
-
Wearing harness and lanyard <br>
-
Proper anchor point selected <br>
-
Proper lanyard selected (protect from striking lower level) <br>
SCAFFOLDING
-
Erected under direction of a competent person <br>
-
Mudsills properly installed under scaffold legs <br>
-
Scaffolding components inspected for damage <br>
-
Cross braces in place at front and rear of scaffolding <br>
-
Scaffolding greater than 10’ from an electrical source <br>
-
Scaffolding fully planked without any gaps <br>
-
Planks extend at least 6” past frame support but less than 12” <br>
-
Guardrails installed on all open sides and ends <br>
-
Top rail located between 38"-45” <br>
-
Midrail installed halfway <br>
-
All toe boards installed and tight to the platform <br>
AERIAL/SCISSOR LIFTS
-
Operator trained in equipment being used <br>
-
Operator verified oil level is proper <br>
-
Operator manual on the lift <br>
-
Occupants using personal fall arrest system and secured off <br>
-
Equipment on a stable surface <br>
-
Factory approved PFAS attachments being used <br>
CONCRETE & MASONRY
-
Rebar caps installed to prevent impalement hazards (flat top only) <br>
-
Masks being used during cutting operations <br>
-
CMU storage maximum 1 cube high <br>
ROOFING
-
Warning lines set minimum of 6’ from roof edge <br>
-
Steep roof pitch greater than 4:12 requires fall protection <br>
-
Material storage set back 10’ from roof edge <br>
-
Fire extinguishers provided on roof <br>
-
Proper access to roof provided <br>
POWER & LIGHTING
-
Electrical room is clean, neat, organized to eliminate trip hazards <br>
-
All energized light sockets are filled <br>
-
Lamps protected by lamp guards <br>
-
Lighting supported every 5’ <br>
-
Tool power on separate circuit from lighting <br>
-
Lighting higher than 8’ AFF <br>
-
PIn use covers installed on exterior receptacles <br>
-
GFCI protection is provided and used <br>
-
Full panel covers installed – dead fronts only in locked rooms <br>
-
Unused breaker openings are covered with blanks <br>
-
No work taking place on energized panels <br>
WELDING/CUTTING
-
Fuel tanks stored upright <br>
-
O2 and fuel tanks separated by at least 20’ <br>
-
Tanks secured to prevent falling/damage <br>
-
Protective caps installed on top of tanks <br>
-
Gauges free from damage <br>
-
Area below welding operation is protected <br>
-
Fire extinguisher readily available <br>
-
Damage to welders leads <br>
-
Torch hoses in good condition <br>
Excavations & Trenching
-
Trench at proper slope, depending on soil conditions
-
Trench box in use, if applicable
-
All slings in compliance
-
Backup alarms working on all equipment
-
Seat belts worn in equipment
-
Ladder in trench
-
Soil piled away from trench
-
PHOTOS
-
Comments
-
Person that completed the report
