Racking Inspection

• Grand Island

  Select

• Conducted on

  Date

• Prepared by

• Location
  Address

• Torque Wrenches Used

Is the drive bearing assembly correctly installed?

• Is the drive bearing assembly angled correctly to the pile?

  Select Yes No N/A

  • Yes
  • No
  • N/A

• Is all bearing hardware present: 2 threaded rods 5/8", 8 hex nuts 5/8", 4 flat washers 5/8", 4 conical washers 5/8" and assembled per the Valmont Manual?

  Select Yes No N/A

  • Yes
  • No
  • N/A

• Is all hardware torqued to 110 ft-lbs (+/-10)?

  Select Yes No N/A

  • Yes
  • No
  • N/A

• Is the hardware torque marked?

  Yes

  No

  N/A

Is the typical bearing assembly installed correctly?

• Is the typical bearing assembly angled correctly to the pile?

  Yes

  No

  N/A

• Is all bearing hardware present: 2 threaded rods 5/8", 8 hex nuts 5/8" 4 flat washers 5/8", 4 conical washers 5/8" and assembled per the Valmont Manual?

  Yes

  No

  N/A

• Is all the hardware torqued to 110 ft-lbs (+/- 10)?

  Yes

  No

  N/A

• Is the hardware torque marked?

  Yes

  No

  N/A

Shared Post Bearing Assembly

Drive Saddle Installation

• Is all saddle hardware present: 1 hex bolt (5/8"-11x 4-1/4"), 2 spacers (22mm OD x 2.5mm WT x 26mm L), 1 hex lock nut 5/8"?

  Yes

  No

  N/A

• Is the hardware torqued to 110 ft-lbs (+/-10)?

  Yes

  No

  N/A

• Is the saddle into tolerance(+/-4 degrees)?

  Yes

  No

  N/A

• Is the hardware torque marked?

  Yes

  No

  N/A

Double Saddle Installation

• Is all saddle hardware present: 1 hex bolt (5/8"x 4-1/4"), 2 spacers (22mm OD x 2.5mm WT x 26mm L), 1 hex lock nut 5/8"?

  Yes

  No

  N/A

• Is the hardware torqued to 110 ft-lbs (+/-10)?

  Yes

  No

  N/A

• Is the saddle into tolerance(+/-4 degrees)?

  Yes

  No

  N/A

• Is the hardware torque marked?

  Yes

  No

  N/A

Single Saddle Installation

• Is all saddle hardware present: 1 hex bolt (5/8"x 4-1/4"), 2 spacers (22mm OD x 2.5mm WT x 26mm L), 1 hex lock nut 5/8"?

  Yes

  No

  N/A

• Is the hardware torqued to 110 ft-lbs (+/-10)?

  Yes

  No

  N/A

• Is the saddle into tolerance(+/-4 degrees)

  Yes

  No

  N/A

• Is the hardware torque marked?

  Yes

  No

  N/A

Actuator Installation

• Is the lower actuator hardware present:1 hex bolt (M14x80mm, 2 spacers (19mm OD x 2mm WT x 7.5mm L), 1 hex lock nut M14?

  Yes

  No

  N/A

• Is the upper actuator hardware present: 1 hex bolt (M14x 120mm), 2 spacers (17 mm OD x 2mm WT x 26.1mm L), 2 conical washers M14, 1 hex lock nut M14?

  Yes

  No

  N/A

• Is the hardware torqued to 85 ft-lbs (+/-10)?

  Yes

  No

  N/A

• is all hardware torque marked?

  Yes

  No

  N/A

Torque Tube Installation

• Is the saddle insert installed onto the torque tube end that will be connected to the 10-bolt pattern side of the double saddle assemblies?

  Yes

  No

  N/A

• Is the torque tube inserted up against the vertical wall of the saddle ( either the drive or short side of double saddle.)?

  Yes

  No

  N/A

• is the torque tube installed past the sight hole on the double saddle?

  Yes

  No

  N/A

• Is the saddle insert flush with the vertical wall of the double saddle?

  Yes

  No

  N/A

• Is the drive saddle to torque tube hardware present: 12 hex bolt (3/8"-16x5), 12 hex lock nut (3/8"-16)?

  Yes

  No

  N/A

• Is the double saddle to torque tube hardware present: 14 hex bolt (3/8"-16x5), 12 hex lock nut (3/8"-16)?

  Yes

  No

  N/A

• Is the single saddle to torque tube hardware present: 4 hex bolt (3/8"-16x5, 4 hex lock nut (3/8"-16)?

  Yes

  No

  N/A

• Is the hardware torqued 20 ft- lbs (+/- 10%)?

  Yes

  No

  N/A

• Is the hardware torque marked?

  Yes

  No

  N/A

Module Rail Installation

• Is type B module rail as shown in the manual at the saddle using the module bracket with all hardware: 2 hex bolt (5/16"-18 x 8-1/2")?

  Yes

  No

  N/A

• Is the type A module rail as shown in the manual on the torque tube using the module bracket with all hardware: 2 hex bolt ( 5/16"-18 x 8-1/2")?

  Yes

  No

  N/A

• Is the module rail installed square to the torque tube?

  Yes

  No

  N/A

• Is the type B module rail at a minimum of 2-3/16" from the saddle.

  Yes

  No

  N/A

• Is the hardware torqued 14 ft-lbs (+/-10%)?

  Yes

  No

  N/A