Supervisor Frame Checklist

• Site conducted

  Select

• Conducted on

  Date

• Prepared by

• Location
  Address

• Builder sign in place & Visible.

  Yes

  No

  N/A

• Silt fence & driveway gravel in place.

  Yes

  No

  N/A

Frame Position

• Check external wall bottom plates do not overhang more than 10mm.

  Yes

  No

  N/A

• Check the external wall bottom plates are not more than 20mm in from the edge of the concrete.

  Yes

  No

  N/A

• Is rebate (brick/AAC/Cladding) correct size & location.

  Yes

  No

  N/A

• Check if lightweight zero lot wall and corner frame internal pins for its position.

  Yes

  No

  N/A

• Check walls are per plan in positioning.

  Yes

  No

  N/A

• Check gaps/dips in slab bottom plates

  Yes

  No

  N/A

• is termite film installed all perimeter.

  Yes

  No

  N/A

• Is 110mm dampcourse stapled to all external bottom plates & wet area walls.

  Yes

  No

  N/A

Tiedown/Bracing

• Tie down fixings to slab at least 50mm from slab edge.

  Yes

  No

  N/A

• Tie down rods/bolts per approved plans & fixed, rods clear of roofing battens and sheeting at top.

  Yes

  No

  N/A

• Cyclone straps to trusses with 6mm mech driven fixing each side

  Yes

  No

  N/A

• Strap lintel to ribbon plate- min 6 nails each side.

  Yes

  No

  N/A

• Provide batten screw connection/creeper bracket to all hip creeper rafters that exceed 1800mm.

  Yes

  No

  N/A

• All wall bracing in position as required on approved plans and properly fixed including tie-down rods, nails not overdriven.

  Yes

  No

  N/A

• Ply bracing nailed off correctly 50mm top/bottom, 150mm sides,300mm internal fixings.

  Yes

  No

  N/A

• Transfer noggings installed connecting bracing walls to trussed roof frame -batten screwed, not nailed.

  Yes

  No

  N/A

• Non load bearing walls connected to trusses with slotted wall brackets where required.

  Yes

  No

  N/A

Other

• Truss layout consistent with the truss plan and fixed at correct centers-rafters/truss strapped to head within 100mm of each truss

  Yes

  No

  N/A

• Are any standard trusses bowed

  Yes

  No

  N/A

• Studs under point loads/girder trusses

  Yes

  No

  N/A

• Roof and truss point loads supported and blocked if required.

  Yes

  No

  N/A

• Check A/C opening space/location.

  Yes

  No

  N/A

• Are steel posts installed. If not will they be ready for lock up?

  Yes

  No

  N/A

• Review beam connections

  Good

  Fair

  Poor

  N/A

• Timber posts cup heads to face the street, recessed washer/nut.

  Yes

  No

  N/A

• is the timber frame mould affected?

  Yes

  No

  N/A

• Check waste pipe locations are per plan.

  Yes

  No

  N/A

• Check floor joist layout as per plan.

  Yes

  No

  N/A

• Particleboard flooring glued/screwed per layout pattern.

  Yes

  No

  N/A

• All boots nailed/screwed correctly.

  Yes

  No

  N/A

• Balcony beams & Joists installed & ends sealed

  Yes

  No

  N/A

• Are fall guards in place-void/openings

  Yes

  No

  N/A