1A15

• Project Name

• Loop ID

• Borehole ID

• Probe ID

  Probe 08

  Probe 02

• Conducted on

  Date
• Location
  Address

TX Set Up

Site Safety

• Vehicle wheel is chocked and E-brake applied?

  Yes

  No

  N/A

• First aid kit with fire extinguisher are on site and easily accessible with up-to-date inspection tags with employee initials beside hole punch. Site ERP plan is also present.

  Yes

  No

  N/A

• Are all generators, jerry cans and fuel contained? (Generator and jerry can's must be contained in separate spill trays)

  Yes

  No

  N/A

• Worksite has adequate signage (Geophysical Survey in Progress etc)

  Yes

  No

  N/A

• All instrumented equipment protected from the weather and all unused equipment put away in appropriate case/storage?

  Yes

  No

  N/A

Transmitter

• Is the electrically rated safety glove present and inspected for proper use?

  Yes

  No

  N/A

• Leads are clean/dry, not crossed. Longer leads are spaced evenly apart (roughly 1 metre) from where they attach to transmitter all they way to loop.

  Yes

  No

  N/A

• Is the TX site shielded from the rain/snow?

  Yes

  No

  N/A

• Is there heat (winter) or fan (summer) for TX site?

  Yes

  No

  N/A

• Honda EM6500SX switch is set to 120/240 volt setting?

  Yes

  No

  N/A

• Trip On Light Indicator (TOLI) button pressed in?

  Yes

  No

  N/A

Current Monitor

• CM is on the Red terminal lead - when putting lead through CM the arrow at bottom of CM is pointing away from TX

  Yes

  No

  N/A

• Current monitor charging? (Blue light)

  Yes

  No

  N/A

• Current monitor turned on? (green light on by pressing button)

  Yes

  No

  N/A

UR

• UR Battery starting the day with full charge without being plugged in?

  Yes

  No

  N/A

• UR clear square waveform seen from phone? (you cannot check square wave while recording, it must be done before you start record)

  Yes

  No

  N/A

Signal Generator

• Signal generated plugged in properly? (Channel 1 port connected at front of signal generator)

  Yes

  No

  N/A

• Channel 1 'On' button pressed (should illuminate green, if output is off, top right of screen it will say "output off")

  Yes

  No

  N/A

• Square wave selected?

  Yes

  No

  N/A

• Frequency button pressed - set to 5.2Hz (or designated frequency)?

  Yes

  No

  N/A

• Amplitude button pressed - Vpp selected with value starting at 1 before increasing) after final Vpp value established lowest decimal place selected (if knob is accidentally nudged during your checks it will make least impact)

  Yes

  No

  N/A

Values

• Frequency (Hz)

• Resistance

• Voltage

• Amplitude (Vpp)

• Current (Voltage/Resistance)

• Wattage (Voltage x Current)

• Notes

Probe Set Up

• Probe is on and has blue and green indicators before starting to record? (GPS 3D fix)

  Yes

  No

  N/A

• Stations and data from previous day deleted

  Yes

  No

  N/A

• Probe tested before calibrations (SEM and Mag Channels)?

  Yes

  No

  N/A

• Once recording, phone is no longer visible to the phone when connecting to WIFI

  Yes

  No

  N/A

• 3 min calibration readings, set to 5 min after?

  Yes

  No

  N/A

Hourly Check

6:00 am

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

7:00 am

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

8:00 am

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

9:00 am

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

10:00 am

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

11:00 am

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

12:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

1:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

2:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

3:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

4:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

5:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

6:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

7:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

8:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)?

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

9:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A

10:00 pm

• What is the Voltage? Note: When leaving fluke on continuous mode for continuous observation (see manual), ensure you do NOT select min/max.

• What is the Battery percentage of the UR?

• Is the generator at least 1/3 full with gas?

  Yes

  No

  N/A

• Is the current monitor on (green light) and plugged in (blue light)?

  Yes

  No

  N/A

• Lights on the UR correct? 'i' symbol = green, battery symbol = green or yellow (depending on level), '1' symbol = blue (means channel 1 recording), satellite symbol = blue (means we have 3D GPS fix). Wifi symbol illuminates blue when connected to phone (LED furthest to left) and red when disconnected (middle LED)

  Yes

  No

  N/A

• Is the TOLI light off? (not illuminated red)

  Yes

  No

  N/A

• All unused equipment put away in proper place (housekeeping organized)

  Yes

  No

  N/A

• Radio check-in with BH crew (stations, status, etc)

  Yes

  No

  N/A