AB ELEVEN Semi Annual Preventive Maintenance

• Conducted on

  Date

• Prepared by

• Location
  Address

Shanklin Shrink Wrapper - Semi Annual PM - Model - F5A/T71 / Serial #: #F0566/T05221

• PM performed By:

• Select date

  Date

• Clean air screen (replace if damaged or worn out)

• Clean rubber roller & wheels

• Change oil in gear box

• Bearing & sprocket for wear

• Lubricate bearing & sprocket

• Comments:

Damark Shrinksystem - Semi Annual PM - Model - MP1418 / Serial #: #6951

• PM Performed By:

• Select date

  Date

• Clean air screen (replace if damaged or worn out)

• Clean rubber roller & wheels

• Change oil in gear box

• Bearing & sprocket for wear

• Lubricate bearing & sprocket

• Comments:

Horizon SL - Semi-Annual PM - Model - SPF30 / Serial #: 023005 * Use "Horizon Stitch liner Users Manual" for reference

• PM Performed By:

• Select date

  Date

• Clean out machine (HOF20 ACF30 SPF30 HTS30)

• Lubricate shaft (see section 6-1 ACF30)

• Lubricate cam folder, bushing (See section 6-1 SPF30 backside)

• Lubricate shafts bushings and grease fittings (See section 6-1 SPF30 front side)

• Lubricate fittings (See section 6-1 HTS30)

• Lightly oil shafts (See section-1 HTS30)

• Comments:

Horizon SL - Semi-Annual PM - Model - SPF30 / Serial # 346016 *Use "Horizon Stitch liner Users Manual" for reference

• PM Performed By:

• Select date

  Date

• Clean out machine (HOF20 ACF30 SPF30 HTS30)

• Lubricate shaft (see section 6-1 ACF30)

• Lubricate cam folder, bushing (See section 6-1 SPF30 backside)

• Lubricate shafts bushings and grease fittings (See section 6-1 SPF30 front side)

• Lubricate fittings (See section 6-1 HTS30)

• Lightly oil shafts (See section-1 HTS30)

• Comments:

Sigma Mueller Martini Trimmer - Semi-Annual PM - Model - 15810401 / Serial #NN36937 *Use "Sigma Trimmer Operating Manual 1581.0401" for reference

• PM Performed By:

• Select date

  Date

• Clean photocells. (Do not use harsh cleaning agents)

• Clean clamp table and cut table (Remove knifes before working in this area)

• Clean entire Machine. (Do not blow dirt into bearing and guide components)

• Remove wastepaper

• Clean and check conveyor and belts for wear, replace if necessary.

• Check for loose screws

• Check function of all stop and safety switches

• Check start warning horn

• Check tension of belts

• Check oil level in oiler and refill if necessary (See section 7.3.4)

• Check water level in separator and clean filter (See section 7.3.4)

• Check spring force of pneumatic springs on the protection cover (Replace if force has weakened)

• Clean control console and filter (See section 7.3.4)

• Check condition of air hose on gripper table

• Grease each knife and cam

• Change oil in indexer and the motor gearbox

• Grease foot cut and head cut ball screws (See section 7.4.5)

• Comments:

Sigma Mueller Martini Cooling Tower - Semi Annual PM - Model - 15820400 / Serial #NN36937

• PM Performed By:

• Select date

  Date

• Clean and check the entire electrical equipment

• Check the function of all emergency stop devices

• Comments:

Sigma Mueller Martini Binder - Semi-Annual PM - Model - 15850412/ Serial # NN23199 * Use Sigma Binder Operating Manual 1585.0413 for reference

• PM Performed By:

• Select date

  Date

• Check all air hoses for wear (Binder)

• Check air cylinder move of foot (Measuring Station)

• Check bushing and replace at least every 3 years (Measuring Station)

• Grease point at universal shaft (Binder Infeed)

• Change bearing in spine glue assembly every two years (Spine Glue)

• Grease large spring (Table Clamps)

• Grease 3 fittings of universal shafts (Nipping Station)

• Change air filter in all electrical cabinets (See Chapter 7.4.3 Binder)

• Clean Photocells. Do not use harsh cleaning agents. (See Chapter 7.4.1)

• Check Suckers and replace if needed (See Chapter 7.4.2)

• Clean any glue spills from the drive gear

• Clean machine thoroughly do not blow dirt onto bearing and guide components

• Check chains and just tension if needed. (See Chapter 7.4.2)

• Check delivery and infeed belts for wear and replace if needed.

• Check protection devices, warning horn, and warning lamps. Check for loose screws.

• Clean control cabinets filters and replace if needed.

• Comments:

WulfTec Pallet Wrapper - Semi-Annual PM - Model - WRT150 / Serial #3938-1-0602

• PM Performed By:

• Select date

  Date

• Clean photo eyes

• Check photo eyes for proper operation

• Visually inspect for damage

• Grease bearing - (Use EP1 ESSO grease to lubricate bearing) -

• Check chains for correct tension

• Clean wrapper

• Lubricate all chains - (Lubricate with Dow Corning 1122 Chain & Open Gear grease)

• Comments:

WulfTec Pallet Wrapper - Semi-Annual PM - Model - WRT150 / Serial #0599-4544

• PM Performed By:

• Select date

  Date

• Clean photo eyes

• Check photo eyes for proper operation

• Visually inspect for damage

• Grease bearing - (Use EP1 ESSO grease to lubricate bearing)

• Check chains for correct tension

• Clean wrapper

• Lubricate all chains- (Lubricate chains with Dow Corning 1122 Chain & Open Gear grease)

• Comments:

Weko RFDi - Semi-Annual PM - Model -RFDi / Serial #525.291251/011 *Use the "Weko RFDi Operating Manual" for reference

• PM Performed By:

• Select date

  Date

• Check the driving belt (See chapter 6.5 in manual)

• Clean rotor plate (See chapter 6.8 in manual)

• Rinse the dampening system (See chapter 6.3 in manual)

• Comments:

Weko RFDi - Semi-Annual PM - Model -RFDi / Serial #505.272664/002 * Use the "Weko RFDi Operating Manual" for reference

• PM Performed By:

• Select date

  Date

• Check the driving belt (See chapter 6.5 in manual)

• Clean rotor plate (See chapter 6.8 in manual)

• Rinse the dampening system (See chapter 6.3 in manual)

• Comments:

Weko RFDi - Semi-Annual PM - Model -RFDi / Serial #510.281038/002 * Use the "Weko RFDi Operating Manual" for reference

• PM Performed By:

• Select date

  Date

• Check the driving belt (See chapter 6.5 in manual) Clean rotor plate (See chapter 6.8 in manual)

• Clean rotor plate (See chapter 6.8 in manual)

• Rinse the dampening system (See chapter 6.3 in manual)

• Comments: