Automation Direct Frequency Drives

• Document No.

• Audit Title

• Client / Site

• Conducted on

  Date

• Prepared by

• Location
  Address

• Personnel

Installation

• Power wires to L1, L2 and L3 for 3 phase and L1 and L2 for single phase

  Yes

  No

  N/A

• Motor leads to T1, T2 and T3

  Yes

  No

  N/A

• Relay between DI1 and DCM.

  Yes

  No

  N/A

• Analog out from Ao and ACM 0-10 Vdc only<br>

  Yes

  No

  N/A

• Analog in to AI and ACM 4-20 ma

  Yes

  No

  N/A

Parameters Motor Setup

• P0.00. Motor voltage.

  Yes

  No

  N/A

• P0.01. Motor ampers

  Yes

  No

  N/A

• P0.02. Motor frequency Default 60

  Yes

  No

  N/A

• P0.04 maximum frequency. Default 1750

  Yes

  No

  N/A

Ramp parameters

• P1.00 stop method. Default 00 ramp

  Yes

  No

  N/A

• 00 - Ramp to stop
  01 - Coast to stop

• P1.01 acceleration time. Default 10 sec.

  Yes

  No

  N/A

• P1.02. Deceleration time. Default 30 sec.

  Yes

  No

  N/A

Volts/hertz settings

• P2.00 volts/hertz a settings. Set to 02

  Yes

  No

  N/A

• 00 - general purpose.
  01 - high starting torque.
  02 - fans and pumps.
  03 - custom

Digital parameters

• P3.00. Source of operation command. Set to 01

  Yes

  No

  N/A

• 00 - keypad.
  01 - external contacts keypad stop is enabled.
  02 - external contacts keypad stop is disabled.
  03 - comm interface keypad stop is enabled.
  04 - comm interface keypad stop is disabled.

• P3.01-P3.10 multifunction terminals. <br>P3.02 external reset. Input to DI3 set to 02

  Yes

  No

  N/A

• P3.11. Output terminal #1. Set to 01 for fault

  Yes

  No

  N/A

• P3.12. Output terminal #2

  Yes

  No

  N/A

• 00 - drive running 01 - Fault 02 - At speed 03 - Zero sped 07 - Over torque 08 - Above current 09 - Below current

Analog parameters

• P4.00. Source of frequency command. Use 03 for 4-20ma input

  Yes

  No

  N/A

• 01- frequency from keypad
  02 - frequency from 0-10 Vdc input
  03 - frequency from 4-20 ma input
  04 - frequency from 0-20 ma input
  05 - frequency from comm interface
  06 - frequency from -10 to + 10 Vdc

• P4.11 analog output. set to 01 for current.

  Yes

  No

  N/A

• 00 - frequency.
  01 - current.
  02 - process variable
  

• P4,12 analog output gain. Default 100%

  Yes

  No

  N/A

Protection parameters

• P6.00. Overload relay. Use 01 for standard motors

  Yes

  No

  N/A

• 00 - frequency drive rated motors.
  01 - standard motors.
  02 - inactive
  

• P6.01. Auto restart. Set to at least 5

  Yes

  No

  N/A

• P6.02. Momentary power loss. Set to 02 to continue running

  Yes

  No

  N/A

• 00 - stop.
  01 - continent running speed search from speed reference.
  02 - continues running speed search from zero speed

• P6.03. Reverse operation. Disable 01

  Yes

  No

  N/A

• 00 - enable.
  01 - disable.

• P6.11 Over current stall prevention. Default 150%. Reduces motor speed when overloaded set to 100% of motor current<br><br>

  Yes

  No

  N/A

• P6.12 maximum power loss time. Set to .3 sec.

  Yes

  No

  N/A

• P6.13. Base block time. Set to 5.0 sec.

  Yes

  No

  N/A

• P6.30. Line lock out. Set to 01. Disable

  Yes

  No

  N/A

• 00 - enable line lock out.
  01 - disable line lock out.