Combustible Dust audit - Isle Pierre - Sawmill

• Document No.

• Audit Title

• Client / Site

• Conducted on

  Date

• Prepared by

• Accompanied by

Barker room

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Log Pockets

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

North Canter

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

South Canter

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

North Gang

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

South Gang

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Board Edger

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Stacker

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Under Gang

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Under Pockets

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Compressor room

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Under Stacker

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Sorter Basement

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Fab shop

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Chipper

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

PDC # 2

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Shaker

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

PDC # 1

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Trimmer Hydraulics

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Konus

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

PDC # 2

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

PDC # 2

• Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  Safe

  At Risk

  N/A

• Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  Safe

  At Risk

  N/A

• Is it at risk due to an upset condition?

  Yes

  No

  N/A

• Does the divisional clean-up schedule show that the area will be cleaned shortly?

  Yes

  No

  N/A

• Is the current clean-up schedule adequate?

  Yes

  No

  N/A

• Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  Yes

  No

  N/A

• Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  Safe

  At Risk

  N/A

• Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  Yes

  No

  N/A

• Ask employee each of the following questions and check if answered correctly (Answer is included)

• Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

• What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

• What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

• Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.