Planer

Tilthoist & Strips

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk or non-compliance due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Planer #1 Infeed

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Planer #1 enclosure

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Planer #2 infeed

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Planer #2 enclosure

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Planer outfeed roof access

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Shaker / Chipper

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Outfeed deck / Trimsaws

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Sorters up

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Stacker / Bander

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Lumber pocket Basement

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Trimsaw basement

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Sorter down

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Main PDC room

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

Energy plant

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Lube tank room

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Are any changes to the program (cleaning schedules, dust mitigation or control at the source) required in order to ensure this condition will not occur again? If yes, please comment by clicking the (...) button to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Sawmill

I/F deck to Canter 1

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Canter 1 I/F to Canter bandmill

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Canter 1 sideboard table

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

VDA to O/F

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Canter 2 I/F to Canter quads

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Canter 2 sideboard table

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

VSS

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

22" step feeder

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

27" Step feeder

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

5 saw East side

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Model C I/F deck

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if you did not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Model C edger

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Edger landing decks

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Canter landing decks

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Lugloader

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Sorter

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Stacker

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Chipper shaker pit area (SE corner)

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Chip Plant

Chip Plant building upstairs

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Chip Plant building downstairs

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Barker room

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Hog / Chip screen upstairs

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

Hog / Chip screen downstairs

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

PDC Room

  • Are primary dust levels acceptable, have they been removed from possible ignition sources such as heaters, electricity, hot work or friction?

  • Are secondary dust levels acceptable, are they at less than 1/8" over 5% of the work area?

  • Is it at risk due to an upset condition?

  • Does the divisional clean-up schedule show that the area will be cleaned shortly?

  • Is the current clean-up schedule adequate?

  • Could the secondary dust have been better controlled at the source? If yes, please comment as to how by pressing the (...) buttons to the right.

  • Are observed employee work practices within the zone consistent with the program (ie. Use of compressed air, hot work practices)?

  • Did you test employees knowledge of combustible dust and its associated hazards? Choose N/A if not.

  • Ask employee each of the following questions and check if answered correctly (Answer is included)

  • Can you tell me the difference between primary and secondary dust? A. Primary dust is found at the dust source and is larger with higher moisture contents than secondary dust that has spread throughout the area on raised surfaces.

  • What is considered an unacceptable level of secondary dust? A. 1/8" over 5% of the work area.

  • What are your responsibilities with regards to mitigation of combustible dust? A. Understand the risk mitigation matrix for my area, understand the divisional dust control plan, recognize, control and report unsafe conditions.

  • Describe the requirements for use of compressed air? A. Fill out a compressed air pre-work card, do not create a dust plume, compressed air is only to be used as a last resort.

The templates available in our Public Library have been created by our customers and employees to help get you started using SafetyCulture's solutions. The templates are intended to be used as hypothetical examples only and should not be used as a substitute for professional advice. You should seek your own professional advice to determine if the use of a template is permissible in your workplace or jurisdiction. Any ratings or scores displayed in our Public Library have not been verified by SafetyCulture for accuracy. Users of our platform may provide a rating or score that is incorrect or misleading. You should independently determine whether the template is suitable for your circumstances. You can use our Public Library to search based on criteria such as industry and subject matter. Search results are based on their relevance to your search and other criteria. We may feature checklists based on subject matters we think may be of interest to our customers.