Drilling Rig Inspection - Ver 2

• Document No.

• Audit Title

• Client / Site

• Conducted on

  Date

• Prepared by

• Location
  Address

• Personnel

Road Access and Lease

• Adequate road direction signs posted

  Yes

  No

  N/A

• Proper road directions communicated

  Yes

  No

  N/A

• Bridge height, weight and width restriction signs

  Yes

  No

  N/A

• Power lines, height restriction and warning signs posted

  Yes

  No

  N/A

• Adequate pull outs

  Yes

  No

  N/A

• Speed limits posted

  Yes

  No

  N/A

• Road and lease clean of rubbish

  Yes

  No

  N/A

• Lease clean and tidy and free of environmental spills

  Yes

  No

  N/A

• Open pits marked and fenced

  Yes

  No

  N/A

• Is lease properly bermed to prevent runoff from entering or leaving lease

  Yes

  No

  N/A

Lease entrance signs

• Drilling contractor entrance sign posted

  Yes

  No

  N/A

• Operator sign posted

  Yes

  No

  N/A

• Are signs clean and legible

  Yes

  No

  N/A

• Do signs have PPE requirements

  Yes

  No

  N/A

• Do signs say H2S warning if required

  Yes

  No

  N/A

• Signage for visitors "Must report to Wellsite Supervisor"

  Yes

  No

  N/A

• Tight hole no admittance if required

  Yes

  No

  N/A

BOP & Well Control Equipment

• BOP shop service current

  Yes

  No

  N/A

• Choke and kill line hoses fire rated

  Yes

  No

  N/A

• All hydraulic hoses and quick couplers within 7 meters of well center fire rated

  Yes

  No

  N/A

• Annular preventer closes within 60 seconds (90 seconds if annular is larger than 350mm)

  Yes

  No

  N/A

• Flow tees installed for flow changes in relief lines (installed in proper orientation)

  Yes

  No

  N/A

• Proper measures in place for draining or blowing relief lines (Ability to blow out lines or drain lines without environmental spills)

  Yes

  No

  N/A

• Relief lines properly staked every 10 meters

  Yes

  No

  N/A

• All BOP studs protrude through nuts

  Yes

  No

  N/A

• Bleed off lines installed properly

  Yes

  No

  N/A

• Pressure test charts available

  Yes

  No

  N/A

• BOP controls properly connected secured and mounted

  Yes

  No

  N/A

• BOP pressure test documented in tour book

  Yes

  No

  N/A

• MACP posted in manifold shack and doghouse

  Yes

  No

  N/A

• BOP drills being preformed and documented in tour book (before any drill out or min 1 time per crew every week)

  Yes

  No

  N/A

• Flare line integrity verified and condition of flare line and flare line components

  Yes

  No

  N/A

• Casing wear test being preformed (every 30 days minimum requirement)

  Safe

  At Risk

  N/A

• Manual locking wheels available

  Yes

  No

  N/A

• All flame type equipment 25 meters from well bore

  Yes

  No

  N/A

• Trip sheets being used, signed and recorded as per regulatory requirements

  Yes

  No

  N/A

• Are degasser and mud systems properly vented

  Yes

  No

  N/A

• Is the stabbing valve and inline BOP available, heated, opened and ready for easy installation on the floor

  Yes

  No

  N/A

• Are the BOPs and BOP system of the right size and pressure rating

  Yes

  No

  N/A

• Diverter line is a minimum of 152mm I.D.

  Yes

  No

  N/A

• Does diverted line have a hydraulic opening valve with a minimum ID of 152 mm

  Yes

  No

  N/A

• Is the HCR valve hydraulically plumbed in a fashion so to open before the annular closes

  Yes

  No

  N/A

Accumulator

• Is the Accumulator the right pressure rating and size

  Yes

  No

  N/A

• Is the Accumulator vented outside away from any potential source of heat or sparks

  Yes

  No

  N/A

• Is the Accumulator 15 meters from well entrance

  Yes

  No

  N/A

• Are the Nitrogen procedures posted by the Accumulator

  Yes

  No

  N/A

• Are the nitrogen bottles charged to a minimum of 12500 Kpa or 1800 PSI

  Yes

  No

  N/A

• Is the nitrogen inlet upstream of the pressure side of the regulators

  Yes

  No

  N/A

• Pressure isolation valves are required if nitrogen inlets are downstream of the pressure regulators

  Yes

  No

  N/A

• Is there a check valve on the discharge side of the accumulator pump

  Yes

  No

  N/A

• Are nitrogen bottles properly stored

  Yes

  No

  N/A

• Does the nitrogen meet the ABSA 10 year certification

  Yes

  No

  N/A

• Does the shear ram/blind ram controls have a proper safety device

  Yes

  No

  N/A

• Do all controls on the accumulator that are not in use properly locked out or blanked off

  Yes

  No

  N/A

• In the Accumulator area, are all dangerous good signs, WHMIS, hearing protection signs, automatic starting signs, and eye protections signs posted

  Yes

  No

  N/A

• Are all accumulator controls properly labeled

  Yes

  No

  N/A

• General housekeeping

  Yes

  No

  N/A

Manifold

• Heated proper for winter operations

  Yes

  No

  N/A

• All electrical in manifold meets Class 1 Zone 2 Classification

  Yes

  No

  N/A

• All valve handles installed

  Yes

  No

  N/A

• Proper gauges installed and calibrated

  Yes

  No

  N/A

• Drill pipe pressure gauge working

  Yes

  No

  N/A

• MACP and mud weight posted

  Yes

  No

  N/A

• Choke positions visible

  Yes

  No

  N/A

• Proper view of rig floor

  Yes

  No

  N/A

• Proper size and pressure rating for well type

  Safe

  At Risk

  N/A

• Nace trim

  Yes

  No

  N/A

• Proper lighting

  Yes

  No

  N/A

• Proper exits and ventilation

  Yes

  No

  N/A

• Good housekeeping and tidiness

  Yes

  No

  N/A

• Proper procedures for operations of manifold posted (hard shut in, soft shut-in)

  Yes

  No

  N/A

• Are all valves properly flagged for opened or closed

  Yes

  No

  N/A

• No smoking signs posted

  Yes

  No

  N/A

Flare Tank

• 8m3 capacity

  Yes

  No

  N/A

• Drained and clean inside

  Yes

  No

  N/A

• Fabricated of heat resistant material

  Yes

  No

  N/A

• Proper grounding

  Yes

  No

  N/A

• Degasser tank separate from flare tank or equipped with baffle plates to prevent fluid blowout

  Yes

  No

  N/A

• Unused lines plugged

  Yes

  No

  N/A

• Ignition system proper distance from flare tank and operational

  Yes

  No

  N/A

• 9 meter load out line

  Yes

  No

  N/A

• Impingement plate installed

  Yes

  No

  N/A

• Flare stacks rigged up properly

  Yes

  No

  N/A

• Condition of connections and all connections tight

  Yes

  No

  N/A

Substructure

• Fall protection around BOPs

  Yes

  No

  N/A

• Walking area around BOPs and cellar area

  Yes

  No

  N/A

• Drive lines to draw works properly guarded

  Yes

  No

  N/A

• All drift pins complete with proper safety pins installed in all beams and spreaders

  Yes

  No

  N/A

• Easy access and escape doors (min -2 opposite of each other) in case of emergency

  Yes

  No

  N/A

• Properly heated for winter operations

  Yes

  No

  N/A

• Flow nipple / mud catcher / air stripper split for easy removal for snubbing operations

  Yes

  No

  N/A

• Cellar drained and free of debris

  Yes

  No

  N/A

• Free of oil and fuel leaks from draw works

  Yes

  No

  N/A

• Condition of air tank and air lines

  Yes

  No

  N/A

• Free of steam and water leaks

  Yes

  No

  N/A

• General housekeeping and tidiness

  Yes

  No

  N/A

Mud Tanks

• Hand rails and fall protection

  Yes

  No

  N/A

• Lockouts for all electrical equipment

  Yes

  No

  N/A

• Signage - All agitators and mix pumps to be locked out before entry into confined mud tank areas

  Yes

  No

  N/A

• Signage - Confined entry code of practice to be reviewed before entering mud tanks

  Yes

  No

  N/A

• Proper toe boards around shale shaker areas

  Yes

  No

  N/A

• Class 1 Zone 1 electrical codes being met for electrical items within 2 meter mud tank and shale shaker plume

  Yes

  No

  N/A

• Class 1 Zone 2 electrical classification outside of the 2 meter plume on mud tanks

  Yes

  No

  N/A

• Proper PPE available and being used in mixing shack and chemical BBL.

  Yes

  No

  N/A

• Tank level monitoring system operating and calibrated proper

  Yes

  No

  N/A

• Trip tank level operative

  Yes

  No

  N/A

• Mixing hopper equipped with ventilation fan

  Yes

  No

  N/A

• Electrical chemical bbl available with proper guarding and controlled substance signage

  Yes

  No

  N/A

• Eyewash facilities available in mixing-shack

  Yes

  No

  N/A

• Mixing pumps properly guarded

  Yes

  No

  N/A

• Degasser tank has fluid it

  Yes

  No

  N/A

• Safety recuse Davit available for cleaning tanks

  Yes

  No

  N/A

• All water and steam valves are gate and not 1/4 ball valves

  Yes

  No

  N/A

• Housekeeping and cleanliness

  Yes

  No

  N/A

Mud Pumps

• Roof fall protection

  Yes

  No

  N/A

• Lockouts available

  Yes

  No

  N/A

• Engine exhausts and turbos heat shielded

  Yes

  No

  N/A

• Batteries in vented box with proper WHMIS labels

  Yes

  No

  N/A

• Pop valves have proper shear pins installed

  Yes

  No

  N/A

• Pop valve shear pins properly marked (color coded)

  Yes

  No

  N/A

• Pop valve lines sloped to drain properly

  Yes

  No

  N/A

• All guards in place and in good condition

  Yes

  No

  N/A

• All high pressure lines properly safety cabled

  Yes

  No

  N/A

• Condition of high pressure lines

  Yes

  No

  N/A

• Eyewash facility

  Yes

  No

  N/A

• Pulsation dampeners with proper WHMIS labels and TDG placards

  Yes

  No

  N/A

• Condition of tools

  Yes

  No

  N/A

• General housekeeping

  Yes

  No

  N/A

• Condition of all electrical equipment

  Yes

  No

  N/A

• Does all electrical meet Class 1 Zone 2 electrical classification

  Yes

  No

  N/A

• Proper signage (hearing protection, safety glasses, lockout procedures, autostart, hard hat areas)

  Yes

  No

  N/A

Generator and Electrical Control Center

• All energized equipment can be locked out

  Yes

  No

  N/A

• All receptacles and breakers identified

  Yes

  No

  N/A

• Properly grounded 2 meters apart

  Yes

  No

  N/A

• Wiring off of ground and walkways

  Yes

  No

  N/A

• Rubber matting under all breaker and control panels

  Yes

  No

  N/A

• Battery in proper vented box with WHMIS labels

  Yes

  No

  N/A

• Condition of power cords and electrical plugs

  Yes

  No

  N/A

• Engine exhaust and turbos heat shielded

  Yes

  No

  N/A

• Engines free of oil and fuel leaks

  Yes

  No

  N/A

• Engine fans and belts guarded

  Yes

  No

  N/A

• Fall protection on roof

  Yes

  No

  N/A

• Fire extinguisher

  Yes

  No

  N/A

• Proper signage (lockout procedures, autostart, hearing protection, no water, high voltage, etc.)

  Yes

  No

  N/A

• Housekeeping

  Yes

  No

  N/A

• 25 meters from well center

  Yes

  No

  N/A

Boiler

• Minimum 1 certified boiler operator per tour

  Yes

  No

  N/A

• Fall protection on roof

  Yes

  No

  N/A

• Heat shield on steam lines

  Yes

  No

  N/A

• Header lockout available

  Yes

  No

  N/A

• Site glass guarded

  Yes

  No

  N/A

• Pump guarded

  Yes

  No

  N/A

• Spare pump

  Yes

  No

  N/A

• Safety pop valves 1 year certification

  Yes

  No

  N/A

• Boiler 1 year certification and license

  Yes

  No

  N/A

• Free of fuel and steam leaks

  Yes

  No

  N/A

• No flammable substances in boiler house

  Yes

  No

  N/A

• Blowdown fluid being proper contained and disposed

  Yes

  No

  N/A

• Blowdown lines secured and marked

  Yes

  No

  N/A

• Blowdown procedure posted

  Yes

  No

  N/A

• Proper PPE supplied

  Yes

  No

  N/A

• Housekeeping

  Yes

  No

  N/A

• Proper emergency exits

  Yes

  No

  N/A

Doghouse

• Fall protection on roof

  Yes

  No

  N/A

• Pins in place with proper keepers

  Yes

  No

  N/A

• Doghouse lights pinned and safety cabled

  Yes

  No

  N/A

• CAODC well control procedures in place

  Yes

  No

  N/A

• BOP controls in place and easily accessible

  Yes

  No

  N/A

• CAODC WASTE management document posted

  Yes

  No

  N/A

• First Aid kit stocked and clean

  Yes

  No

  N/A

• JSAs and risk assessment and hazard ID available

  Yes

  No

  N/A

• Safety meetings records available

  Yes

  No

  N/A

• Well records available for crews

  Yes

  No

  N/A

• BOP Drills, Engine kills, check crown saver, documented in tour book

  Yes

  No

  N/A

• Well License posted

  Yes

  No

  N/A

• Proper exits with proper door handles and door swing orientation

  Yes

  No

  N/A

• MACP posted

  Yes

  No

  N/A

• Stick diagram posted

  Yes

  No

  N/A

• MSDS book available and current

  Yes

  No

  N/A

• Hearing protection and safety glasses wash station supplied

  Yes

  No

  N/A

• Eyewash station supplied and clean

  Yes

  No

  N/A

• Electrical components meet Class 1 Zone 2 electrical code

  Yes

  No

  N/A

• Safety belts and lanyards stored properly, clean and in good condition

  Yes

  No

  N/A

• Bulletin board

  Yes

  No

  N/A

• Hydraulic cable cutter supplied

  Yes

  No

  N/A

• Properly heated

  Yes

  No

  N/A

• General condition of all hand tools

  Yes

  No

  N/A

• Emergency phone numbers posted

  Yes

  No

  N/A

• Housekeeping

  Yes

  No

  N/A

• Floor is in good condition (not slippery)

  Yes

  No

  N/A

• Proper radio / phone communication to Wellsite unit

  Yes

  No

  N/A

• Proper signage at doghouse (noise levels, hearing protection, nonsmoking, drug and alcohol policy in effect,all incidents must be reported, etc.

  Yes

  No

  N/A

Documents

• Trip sheets completed and signed

  Yes

  No

  N/A

• Weekly safety meeting books with records

  Yes

  No

  N/A

• Drilling Rig health and safety committee guidelines

  Yes

  No

  N/A

• Operators health and safety guideline posted

  Yes

  No

  N/A

• Drilling program available

  Yes

  No

  N/A

• Company Policies and safety culture posted

  Yes

  No

  N/A

• Pressure test charts available

  Yes

  No

  N/A

• Drilling contact on site emergency Contingency manual available

  Yes

  No

  N/A

• Notice of supervisor posted

  Yes

  No

  N/A

• Copy of OH&S regulations available

  Yes

  No

  N/A

• MSDS available for controlled mud products

  Yes

  No

  N/A

Rig floor

• Lockout on draw works

  Yes

  No

  N/A

• Proper guarding over moving mechanical equipment

  Yes

  No

  N/A

• Crown saver working

  Yes

  No

  N/A

• EAll electrical components within 3 meters of well entrance plume meets Class 1 Zone 1 electrical code

  Yes

  No

  N/A

• Kelly hose safety cabled on both ends

  Yes

  No

  N/A

• Top drive service loop hanging properly no impact or rubbing areas on floor or derrick

  Yes

  No

  N/A

• Line spooled safety line

  Yes

  No

  N/A

• All lifting slings in good condition and load rated

  Yes

  No

  N/A

• Condition of tongs, pipe spinner and safety holdback lines

  Yes

  No

  N/A

• Proper hole cover and mouse hole cover

  Yes

  No

  N/A

• Condition of slips and dog collars

  Yes

  No

  N/A

• Snubbing post at V-door

  Yes

  No

  N/A

• Mud can available and mud can condition

  Yes

  No

  N/A

• Proper lighting on floor

  Yes

  No

  N/A

• Housekeeping

  Yes

  No

  N/A

• Brake handle hold down chain

  Yes

  No

  N/A

• All draw works controls properly identified

  Yes

  No

  N/A

• Draw works free of air leaks

  Yes

  No

  N/A

• Proper exits from floor area (3)

  Yes

  No

  N/A

• Warning horn working properly

  Yes

  No

  N/A

• Condition of tugged and winch cables

  Yes

  No

  N/A

• Condition of drilling line

  Yes

  No

  N/A

• V-door opening properly safety chained

  Yes

  No

  N/A

• Condition of V-door stairs

  Yes

  No

  N/A

• Proper storage of drilling subs and tools on flor

  Yes

  No

  N/A

Derrick

• All fasteners with bolts have lock nuts or cotter safety pins

  Yes

  No

  N/A

• All repairs or alterations have been documented in the CAODC log book

  Yes

  No

  N/A

• Crown has a bumper block with mesh wrapping

  Yes

  No

  N/A

• Rig is equipped with a proper block hanging line

  Yes

  No

  N/A

• Money board fingers are straight and safety chained

  Yes

  No

  N/A

• Monkey board has wind boards

  Yes

  No

  N/A

• Mast certification is posted on the Derrick

  Yes

  No

  N/A

• Ladder is in good condition within 6 inch toe room

  Yes

  No

  N/A

• Escape buggy is accessible and in good condition

  Yes

  No

  N/A

• Escape line in good condition and mounted on a proper anchor bloc

  Yes

  No

  N/A

• Climbing assist supplied and in good condition

  Yes

  No

  N/A

• Proper fall arrest on monkey board and Derrick

  Yes

  No

  N/A

• All sheaves properly secure and safety cabled

  Yes

  No

  N/A

• Crown sheave in good condition

  Yes

  No

  N/A

• No loose tools in Derrick

  Yes

  No

  N/A

• Properly tethered tool set with log book available

  Yes

  No

  N/A

• All pins in place with safety pins installed

  Yes

  No

  N/A

• Lighting operation meets electrical classification and safety cabled

  Yes

  No

  N/A

• Derrick inspected before raising the Derrick and documented in tour book

  Yes

  No

  N/A

• Condition of tong lines safety cables

  Yes

  No

  N/A

• Electrical fixtures all in good condition

  Yes

  No

  N/A

• Top drive torque tube properly mounted

  Yes

  No

  N/A

• Top drive service loop strung properly

  Yes

  No

  N/A

Travelling Assembly / Top Drive / Swivel

• Sheaves are properly guarded

  Yes

  No

  N/A

• Top drive / Swivel free of oil and mud leaks

  Yes

  No

  N/A

• All fasteners properly pinned or bolted with locknuts

  Yes

  No

  N/A

• Weight indicator calibrated proper

  Yes

  No

  N/A

• Weight indicator safety cabled

  Yes

  No

  N/A

General Safety and Safety Procedures

• Site specific ERP on location and has been reviewed and tested

  Yes

  No

  N/A

• Prejob hazard assessment/meetings are completed before tasks are done. All controls are put in place

  Yes

  No

  N/A

• Gas detection on site and properly calibrated

  Yes

  No

  N/A

• Daily walk around done by Rig Manager and Wellsite representative and documented

  Yes

  No

  N/A

• JSAs are continually being used and updated

  Yes

  No

  N/A

• General housekeeping throughout the rig

  Yes

  No

  N/A

• basic crew knowledge of safety systems

  Yes

  No

  N/A

• Crew attitude toward safety and safety systems good

  Yes

  No

  N/A

• Crew participation in safety meetings, near miss reporting

  Yes

  No

  N/A

• BOP drills being performed (crew well control knowledge)

  Yes

  No

  N/A

• Man down drills being performed if required

  Yes

  No

  N/A

• Back in parking being communicated and being done

  Yes

  No

  N/A

• Spotters always provided for heavy equipment backing up

  Yes

  No

  N/A

• New employees and personnel identified and properly orientated

  Yes

  No

  N/A

• rig floor danger zone identified and marked

  Yes

  No

  N/A

• Power catwalk zone is classified as a restricted area and 10 meter no go zone flagged when catwalk is in operation

  Yes

  No

  N/A

• Restricted areas all flagged, barricaded and identified

  Yes

  No

  N/A

• Lease hazards are communicated to everyone on location

  Yes

  No

  N/A

• Lease is properly lighted

  Yes

  No

  N/A

• Refuse properly contained

  Yes

  No

  N/A

• Safe work permits and hot work permits being used

  Yes

  No

  N/A

• Rental equipment properly rigged up

  Yes

  No

  N/A

• Operating procedures supplied and crew training provided for natal equipment

  Yes

  No

  N/A

• Rental equipment properly grounded and meets electrical codes

  Yes

  No

  N/A

• Proper signage on rental equipment

  Yes

  No

  N/A

• Rental equipment proper size for job being done

  Yes

  No

  N/A

• Rental equipment free of fuel oil mud or steam leaks

  Yes

  No

  N/A

• All tanks are proper for fuel spill containment or meet fuel tank spill regulations

  Yes

  No

  N/A

• Pipe racks are level and choked and chained together

  Yes

  No

  N/A

Crew Training Tickets

• Drillers have first line bop tickets

  Yes

  No

  N/A

• H2S Alive training tickets

  Yes

  No

  N/A

• First aid tickets

  Yes

  No

  N/A

• Second line well control for Wellsite Supervisors and Rig Manager

  Yes

  No

  N/A

• Boiler tickets (min 1 per crew)

  Yes

  No

  N/A

• Fall arrest / rescue training

  Yes

  No

  N/A

• WHMIS and TDG training

  Yes

  No

  N/A

• Loader operator training

  Yes

  No

  N/A

Breathing Apparatus

• Condition of face piece good

  Yes

  No

  N/A

• Air cylinders full of air less than 1 year old

  Yes

  No

  N/A

• Adequate number of packs

  Yes

  No

  N/A

• Low pressure alarm working

  Yes

  No

  N/A

• Positive pressure

  Yes

  No

  N/A

• Clean and stored properly

  Yes

  No

  N/A

• Crews properly trained on donning air packs

  Yes

  No

  N/A

• Spare air cylinders in good condition

  Yes

  No

  N/A

Rig Site Trailers / Living Quarters

• First aid kits available

  Yes

  No

  N/A

• Equipped with fire extinguishers

  Yes

  No

  N/A

• Smoke alarms working

  Yes

  No

  N/A

• CO2 detectors

  Yes

  No

  N/A

• Proper knock out windows

  Yes

  No

  N/A

• Spotted 2 meters end to end apart to meet fire regulations

  Yes

  No

  N/A

• Bedrooms have proper fire escape windows or doors

  Yes

  No

  N/A

• Propane bottle current certification

  Yes

  No

  N/A

• Power cords strung proper off of the ground

  Yes

  No

  N/A

• Sewage being treated or properly contained and hauled away

  Yes

  No

  N/A

• Main entrances have people landings and steps

  Yes

  No

  N/A

Toolhouse / Watertank / Fuel Tank / Parts Storage

• Fuel pumps free of leaks and guarded

  Yes

  No

  N/A

• Fuel tanks free of leaks and have proper TDG and WHMIS labels

  Yes

  No

  N/A

• Fuel lines are free of leaks and rigged up neatly out of harms way

  Yes

  No

  N/A

• Fuel fill-up hose has proper fill-up nozzle with isolation valve next to tank

  Yes

  No

  N/A

• Are all main storage fuel tanks designed to comply with transportation regulation

  Yes

  No

  N/A

• Are all small storage/transfer tanks designed with proper spill containment

  Yes

  No

  N/A

• Are all fuel tanks a safe distance from open flames and engine exhaust

  Yes

  No

  N/A

• Do the main fuel storage tanks have proper access ladders/stairs with fall protection

  Yes

  No

  N/A

• Are water pumps free of leaks and properly guarded

  Yes

  No

  N/A

• Are water lines free of leaks and rigged up neatly

  Yes

  No

  N/A

• Are steam lines covered with insulation or heat shielding where contact with personnel is possible

  Yes

  No

  N/A

• Are steam lines free of leaks

  Yes

  No

  N/A

• Do all steam hoses have properly pressed on or Boss fitting ends to prevent coming apart under pressure

  Yes

  No

  N/A

• Are all controlled substances stored properly with WHMIS labels and have MSDS sheets for them

  Yes

  No

  N/A

• Are parts all stored neatly and organized

  Yes

  No

  N/A

• Are all parts lockers clean and free of rubbish and junk

  Yes

  No

  N/A

• Are all hand tools and electric tools in good condition and in safe operating condition

  Yes

  No

  N/A

• Is the rig equipped with a properly tethered tool set for working up the derrick

  Yes

  No

  N/A

• Do air compressors have proper pressure relief pop valves

  Yes

  No

  N/A

• Do all air tanks comply with all Regulations and have been certified within the last 5 years

  Yes

  No

  N/A

• Are air compressors properly guarded

  Yes

  No

  N/A

• Are all air tanks equipped with proper drain plugs

  Yes

  No

  N/A

• Does the Air Chemical addition pot have a proper bleed off valve on the cap

  Yes

  No

  N/A

• Are air compressors located in a dry, well ventilated area, free of natural gas and water vapor

  Yes

  No

  N/A

• Are propane bottles stored outside and mounted securely for transportation

  Yes

  No

  N/A

• Are oil storage bins mounted securely - Contents identified have proper WHMIS labels and proper TDG labels

  Yes

  No

  N/A

• Is there proper storage for 210 liter drums of oil and chemicals

  Yes

  No

  N/A

• Are all entrances and walkways clean and free of loose parts, tools and equipment causing slip and trip hazards

  Yes

  No

  N/A