Factory Checklist

• Conducted on

  Date

• Prepared by

• * The following list is to decrease items being missed and help in detecting mistakes before site. This form needs to be completed and emailed to Management as soon as possible.
  * All cabinetry, kicks and bulkheads need to be stacked neatly and as tightly as possible with good access to the rest of the factory
  * Hardware and boxed items should be stacked with the job during checklist completion to make sure they are not missed on delivery
  * All panels, bench tops, kick faces and any flat items should be stacked neatly in the front of the factory in job lots with tape marking each job
  
  Add photos if and where required

CABINETRY

• All cabinets are assembled

  Yes

  No

  N/A

• All cabinets are marked clearly

  Yes

  No

  N/A

• Cabinets drilled for installation to other cabinets

  Yes

  No

  N/A

• Cabinets drilled for panels

  Yes

  No

  N/A

• Cabinets drilled for fillers

  Yes

  No

  N/A

• Adjustable shelves accounted for

  Yes

  No

  N/A

• Cabinets over 800 backs drilled for adjustable

  Yes

  No

  N/A

• All doors fitted

  Yes

  No

  N/A

• All drawers fitted

  Yes

  No

  N/A

• All gallery rails installed

  Yes

  No

  N/A

• All panels accounted for

  Yes

  No

  N/A

• All specialty hardware installed

  Yes

  No

  N/A

• All handles drilled

  Yes

  No

  N/A

• Spreader rails installed for drawers

  Yes

  No

  N/A

• All push caches installed

  Yes

  No

  N/A

• Cutlery tray installed

  Yes

  No

  N/A

• Any open shelving is assembled

  Yes

  No

  N/A

• Screws in dishwasher opening are 50mm hole head

  Yes

  No

  N/A

WALK-IN PANTRY

• All shelves accounted for

  Yes

  No

  N/A

• All mullions accounted for

  Yes

  No

  N/A

• All backs accounted for

  Yes

  No

  N/A

• All divisions accounted for

  Yes

  No

  N/A

• Heights and widths checked and are correct

  Yes

  No

  N/A

• All adjustable shelf holes correspond

  Yes

  No

  N/A

• Hinges and hinge blocks

  Yes

  No

  N/A

BLIND CORNERS AND CORNER VOIDS

• Support packers for wall

  Yes

  No

  N/A

• Corner fillers screwed together with supports

  Yes

  No

  N/A

• Packers for blind cabinetry to make up void size

  Yes

  No

  N/A

DOWNLIGHTS

• Downlights installed

  Yes

  No

  N/A

• Transformers and power supplys

  Yes

  No

  N/A

• Wire extensions if needed

  Yes

  No

  N/A

KICKS

• All kicks assembled

  Yes

  No

  N/A

• 450 maximum spacings between divisions

  Yes

  No

  N/A

• All kicks screwed

  Yes

  No

  N/A

• Whiteboard kick returns

  Yes

  No

  N/A

BULKHEADS

• All bulkheads assembled

  Yes

  No

  N/A

• All bulkheads have been puttied and car bogged

  Yes

  No

  N/A

• All bulkheads have been sanded

  Yes

  No

  N/A

SINK CABINETS

• 2x1 on edge rail installed

  Yes

  No

  N/A

• Check sink size and rout ends if needed

  Yes

  No

  N/A

• Bowl depth checked and sink hinge blocks correct

  Yes

  No

  N/A

OVEN CABINETRY

• Oven model corresponds with cabinetry sizes

  Yes

  No

  N/A

• No rail at back of cabinet for floor units

  Yes

  No

  N/A

• Oven opening has ventilation holes cut

  Yes

  No

  N/A

• Oven and microwave tower pre-installed

  Yes

  No

  N/A

RANGEHOODS

• Range hood is installed

  Yes

  No

  N/A

• Instructions removed from inside of rangehood

  Yes

  No

  N/A

• Ducting path has been observed and boxed

  Yes

  No

  N/A

• Required ducting and vent supplied

  Yes

  No

  N/A

COOKTOPS

• Cabinetry under cooktop has 2x1 rails on edge

  Yes

  No

  N/A

• Cabinetry ends routed if cooktop over 30mm

  Yes

  No

  N/A

DISHWASHER FILLERS

• Correct height and length dishwasher frame is made

  Yes

  No

  N/A

• Kick plates for inter/semi-inter or built under dishwasher

  Yes

  No

  N/A

• If a dish drawer appropriate cut outs in drawer and kick

  Yes

  No

  N/A

• If integrated 2x1 with magnetic brackets set up

  Yes

  No

  N/A

LAMINATE BENCHTOPS

• Toggle bolts

  Yes

  No

  N/A

• Tops checked for damage

  Yes

  No

  N/A

• All tops accounted for

  Yes

  No

  N/A

• Check mitres join correctly

  Yes

  No

  N/A

TIMBER BENCHTOPS

• Bench tops are correct size

  Yes

  No

  N/A

• Bench tops have had two to three coats of oil on both sides

  Yes

  No

  N/A

VANITIES

• Aluminium angle for wall hung vanities

  Yes

  No

  N/A

• Cut out in tops for wall hung vanities

  Yes

  No

  N/A

MISCELLANEOUS

• Sufficient packing is with job

  Yes

  No

  N/A

• Handles with job

  Yes

  No

  N/A

• All hardware for missing drawers

  Yes

  No

  N/A

• All hardware for missing doors

  Yes

  No

  N/A

• Contract checked and all speciality hardware fitted

  Yes

  No

  N/A

• Appliances as per contract if provided by Everlong

  Yes

  No

  N/A

• Appliance that were delivered to shed for fitting

  Yes

  No

  N/A

• All drawer covers

  Yes

  No

  N/A

• 87 degree stops accounted for and packed

  Yes

  No

  N/A

DELIVERY

• All above items to be loaded

  Yes

  No

  N/A

• Plasterboard sheets if required

  Yes

  No

  N/A

• MDF cover sheets if required

  Yes

  No

  N/A

• Delivery should be easy and time efficient if all jobs are stacked as in the notes above

• Add signature

  Sign