Gigacomm Site Design Brief (Coax) Amendments in progress (do not use)

• Site conducted

  Select

• Conducted on

  Date

• Prepared by

• Location
  Address

• Version Control - 1

• The purpose of this document is to assist field teams, designers, OHS and other Gigacomm employees and partners to assess a buildings viability for a Gigacomm service. This Document designed to assist in the understanding of the building topography and layout for design, installation and safety requirements for Gigacomm services and future upgrades.

• Does the site currently utilise an embedded network to supply their internet services?

  Yes

  No

  N/A

• Define the Embedded Network provider

• Is there a, base building owned, structured copper cabling network throughout the building and to all apartments that can be utilised for a GigaComm standard installation?

  Yes

  No

  N/A

• Proceed with SDV as per standard installation requirement

• Yes

  No

  N/A

• Proceed with a Coax Site Design Survey

• Identify satellite and Free-to-air antenna’s (FTA) on rooftop. Provide photos.

  Media

• Find ‘first’ splitter and/or amplifier and identify whether the coax is one of the following:

• a. Shared (Sat and FTA)

  Yes

  No

  N/A

• b. Single use Satellite

  Yes

  No

  N/A

• c. Single use FTA

  Yes

  No

  N/A

• Provide the number of coax cables going up and down the riser

• Number of coax cables entering each apartment

• The type of coaxial cable (RG59, RG6, RG11) – RG59 is bad, RG6 is good, RG11 is best - IF FOUND RG59 THEN DO WE CONSIDER SDV COMPLETE??

• If previously identified as a shared, no further work required, consider SDV complete

  Yes

  No

  N/A

• If not Shared, continue with SDV

• Provide description of model names and technologies used for splitters, amplifiers, diplexers.

• Provide High-res photos of splitters, amplifiers, diplexers etc (for the three upper most floors and a fourth lower floor with coax/splitter hardware) so as to identify operating frequencies (ie. 5 – 694MHz, 5 – 2400MHz etc)

  Media

• Provide a rough wiring diagram showing rooftop cable entry to splitters, amplifiers, diplexers etc including signal direction (in/out) - For the three upper most levels along with a lower level that contains coax/splitter hardware

  Media

• Photo Type: Standard - Used for site access, cable routes, overall photos and general site photos - Resolution: 1074 x 768 - File Type: JPEG – Ratio: 4:3 – Size: <500kb

• Photo Type: High resolution photos - Used for line-of-sight photos, N/S/E/W photos - Resolution: 5168x 3872 - File Type: JPEG – Ratio: 4:3 - Size: 5Mb

TECHNOLOGY MIX

• mmWave dish?

  Yes

  No

  N/A

• Node broadcast antenna?

  Yes

  No

  N/A

• Node CPE?

  Yes

  No

  N/A

• Dark Fibre?

  Yes

  No

  N/A

BUILDING CONFIGURATION

• Rooftop?

  Yes

  No

  N/A

• MDF?

  Yes

  No

  N/A

• IDF?

  Yes

  No

  N/A
MDF/IDF Details

• Identify Building Eg. 1 of 3 or Block A

• Please provide a photo of the existing Building Entry Point (BEP) - lead-in conduit within the building

  Media

• Which floor is the MDF on? (please comment about location)

• Which floors/apartments are served by MDF?

• Distance from MDF to vertical risers, please detail route with comments (what is the length horizontally along cable tray routes?)

• What floors are the IDFs on?

• Which IDFs service which floors/apartments?

• Provide Photos of all Risers. Photo of entire riser (wide angle)

• Photo of riser left wall (wide angle)

• Photo of riser right wall (wide angle)

• Photo of riser floor and penetrations (wide angle)

• Photo of riser roof and penetrations (wide angle)

• Building Height (m)?

• Height of each floor (m)?

• Number of floors?

• Which floors have apartments?

• Number of apartments/units in each floor (per tower/block)

• Riser locations are the same across floors of the building, if not, please raise it as “cable length risk”?

• Mark up Cables feeding in/out of the proposed Gigacomm device location such as MDF/Electrical riser run Horizontal, Vertical and or Other

  Media

• Please Provide Supportive Photos of MDF and IDF

  Media

• Provide Photos of MDF Jumpering Record Book and all written pages

  Media

• Provide Photos of all IDF Jumpering Record Book and all written pages

  Media

• Provide general photos of any existing Carriers Equipment in and around the MDF Room

  Media

IN BUILD EQUIPMENT

• Roof top wall box (RTWB)?

  Yes

  No

  N/A

• FOBOT?

  Yes

  No

  N/A

• DPU?

  Yes

  No

  N/A

• 9RU Cabinet?

  Yes

  No

  N/A

• Are you proposing 9 RU in a location other than MDF Room or where Telstra Lead-in comes in.

  Yes

  No

  N/A

• Gigacomm require a presence in MDF for a fibre lead-in, therefore please provide photos of suitable location for an HD FOBOT in MDF Room.

  Media

• Provide path and distance for a fibre cable tie from HD FOBOT to 9 RU. ( Please note: this is required even if an antenna mount design is proposed).

  Media

• If available space doesn't allow for a 9 RU cabinet, will a 5 RU Shallow Cabinet or 6 or 4 RU Cabinet Fit?

ROOF TOP INFORMATION

• Identify Building Eg. 1 of 3 or Block A

• Existing Penetration?

  Yes

  No

  N/A

• Check for suitable location to install Gigacomm equipment (antenna to be installed at highest practical location allowing for a 360* panorama view, Rooftop wallbox to be installed at a height for easy access/maintenance)

  Yes

  No

  N/A

• Check for existing rooftop earthing (earthing bar, existing steel structure, existing lighting arrestor)

  Media

• If NO existing earthing - propose suitable path to nearest earth point or switch room earth bar. (Include photo artefacts)

• Mark-up distance from existing arrestor to propose antenna frame/dish

  Media

• Please provide photos of fire stairs for antenna mount transportation to the roof. (Wide angle photo)

  Media

• How do we access the roof? (eg. Portable ladder, existing stairs or hatch etc)

  Media

• Provide measurement of roof access hatch or door

• Provide photos of existing anchor points and current proof of valid certification.

  Media
PROPOSED EQUIPMENT DETAILS

• Identify Building Eg. 1 of 3 or Block A

• Proposed Rooftop ANTENNA Location

• Distance b/w RTWB & Riser (m). Provide marked up photos to support

• What is Distance b/w RTWB & 9RU Cabinet (m)? Maximum distance for 9RU cabinet and antenna is 100m for PoE limitation (Ideally as close to antenna as possible. Eg. Lift Motor Room/Plant Room)

• Proposed DPU LOCATION (s)?

• What is distance between each DPU and furthest apartment (m)?Max. copper distance for each DPU , 70m. GigaComm allows 75m but this should affect very few apartments (Calculation for the furthest apartment should factor in additional 10m from the front door of the apartment to the phone jack point. )

• Riser to furthest apartment distance?

• Is there existing power source which can be used to power up 9RU cabinet? If Yes, provide photo and path of power source to be used. Please note: Can utilise existing nearby GPO (other than NBN's Power) - list other services using GPO. Other alternative is a House Distribution Board (not Tenant Board).

• Is there existing power source which can be used to power up each DPU? If Yes, provide photo and path of power source to be used. Please note: Can utilise existing nearby GPO (other than NBN's Power) - list other services using GPO. Other alternative is a House Distribution Board (not Tenant Board).

  Yes

  No

  N/A

• Mark up photos to show equipment connection - Antenna to RTWB to 9RU to each FOBOT & DPU & GPO

  Media

CABLING ROUTES

• Comments about route (include potential obstructions, building material for penetrations)

EXISTING INFRASTRUCTURE

• Provide details about existing penetrations and new core hole requirements

• Provide details of existing cable tray and highlight any new cable tray requirements

GENERAL BUILDING INFORMATION

• Are there any known GigaComm sites nearby? If not known, please call GigaComm representative to check

• Confirm site access contact details (bldg. manager/owner Contact detail if applicable):

• Is there any known special access or security requirements for the site and any surrounding buildings or floors? (if yes, please ask for details) E.g. Supplying evidence of qualifications and licenses.

• Is there a site induction required?

  Yes

  No

  N/A

• Can site be accessed 24/7? (If yes, request for out of hours contact details):

• Does site consist of multiple building?

  Yes

  No

  N/A

• Does site have alternate address or 2nd building entry point from side or cross St?

• Parking and material unloading details, i.e. loading dock, street only etc:

• Any mechanical aids required, i.e. EWP, Large Ladders etc? If yes, please detail

• Dependencies or risks (HSE, site specific etc):

EXISTING SERVICES – OTHER CARRIER

• Can you identify any other ISPs, carriers or relevant parties in equipment rooms, on RTs and in general work area in MDF room (NBN, TPG, Telstra)

SITE SPECIFIC

• "If an Antenna is to be installed how would the steelwork/3.5m pole get to roof top?

  External

  Lift

  Stairs

• “Fire/Smoke alarms isolation needed?”

  Yes

  No

  N/A

• “ Power Outage is required or not”

  Yes

  No

  N/A

• “ Third Party Carrier ie TPG or NBN need to be notified for Temporary Outage or Installation activities”

  Yes

  No

  N/A

ADDITIONAL ARTEFACTS AND COMMENTS

• General Comments

• Building external photos

  Media

• Building lobby photos

  Media

• Letter Box Photos

  Media

• Building onsite Floor Plans or Fire Evacuation Diagram

  Media

• MDF room Photos

  Media

• Provide 360 degree photos of MDF Room

  Media

• Provide photos of existing existing Krone Frame

  Media

• Provide photos of proposed equipment locations including measurements

  Media

• Add media

  Media

• IDFs/Comm room Photos

  Media

• Roof top Photos showing LOS for 360 degrees

  Media

NEAR MAP OR GOOGLE EARTH MARK-UP

• Mark up location of proposed cable route using google earth/nearmap (required for a multi building site)

  Media

• Mark up location of MDF/IDF/RISERS/Proposed antenna location using google map/nearmap

  Media

• Show Building height using nearmap/google earth

  Media

Mount Adequacy Photos

• Mount Adequacy photos showing roof material structure and structural details

  Media

• Provide photos of underneath roof structure if possible or slab thickness estimate

  Media

• Markup proposed location of antenna on photos and nearmap or Google Maps

  Media