Title Page
-
Document No.
-
Audit Title
-
Client / Site
-
Conducted on
-
Prepared by
-
Location
-
Personnel
TILES
-
Tiles delivered as per the tile selection sheet
-
The plumbing pipes are in correct position as per the plan
-
Floor wastes have been installed as per addenda (plastic/ chrome/ round / square)
-
Floor wastes are not damaged
-
Are floor tiles and wall tiles sizes equal? <br>(If not half bond required. A no charge variation signed by the owner is required for half bond tiling before the tiling is to commence)
-
Cupboard tops not used as work bench
-
The description of the box of tiles corresponds to clients colour selection
-
The shade code (tonality No.) and calibre code (size) are the same on all cartons
-
The quantity received is correct and is enough to complete the job- delivery quantity matches order
-
Tiles do not have visual defects or shaded variations
-
Any adjustments must be within +/- 4mm
-
Kickboard tiles be fixed with a construction adhesive not a cement based tile glue.
SCREED
-
Floor wastes have not been slotted. If slotted pipe to be removed and straightened at elbow located in slab
-
Screed is dry enough to accept waterproofing to avoid efflorescence
-
Screed not soft or dummy prior to tiling and not sandy in colour. Correct mix ratio 1:4
-
Screed has correct falls to floor wastes
-
Hobs must be flat with no holes inside or out
-
Two days drying time before waterproofing membrane can be applied (Summer 1 Day)
-
Main floor or bathroom should be screeded to allow the applicator to apply the 100mm application from hob onto main floor area as per BCA requirements
WATERPROOFING
-
Waterproofing silicone bond breakers installed as per detail
-
Waterproofing has bandage 100mm out from corners as per detail
-
Waterproofing 150mm past up and over hobs
-
Waterproofing 1200mm high and to floor of all showers
-
Waterproofing 1200mm high and to floor of all showers
COMPLETION
-
Floor wastes grouted and level with tiles
-
No drummy tiles
-
Grout joint width minimum 1.5mm max 3mm
-
Tilers uses correct notched trowel <br>150 x 150 TILE 6mm x 6mm - 200 x 200 TILE 8mm x 8mm - 250 x 250 TILE 10mm x 10mm<br>300 x 300 TILE 12mm x 12mm - 400 x 400 TILE AND ABOVE 12mm x 12mm BUTTERING<br>Notching ribs to be horizontal for walls
-
Rubber based flexible adhesive to be used
-
Tile adhesive dry before grouting to avoid efflorescence
-
Tile spacers have all been removed prior to grouting
-
Grout has no holes or air bubbles
-
Grout joints have been struck/ tooled to have a compressed sealed finish
-
Grout not applied too wet to avoid efflorescence
-
Tiles not lapping greater than 2mm
-
Tiling is square and plumb to walls and hobs
-
Water drains towards floor wastes and is not ponding
-
All rubbish placed in neat safe pile at front of home
-
All corners to benchtops and bath tile junctions to be left clear for sealing by others. 2-3mm gap required.
-
House left tidy and clean
-
Fit tiles touching plaster plugs
-
All mitred tiling completed as per plan and addenda
-
Tiles have been installed as per plan/ addenda and the tile selection sheet from the supplier of the tiles
-
Tap sets fully grouted to be sealed in showers with silicone by plumber
-
Grout joints consistent in size and colour
-
Tiles to be cleaned with dry cloth on completion
-
Adhesive glue not skinned over
-
Floor and shower wastes not clear and not blocked with grout, glue, screed, cement , etc.
