IHS QC Document

• Site ID and Name

• Location
  Address

• Inspection Date

  Date

• Prepared by

• Installation Subcontractor

  Select Clay Electrical EXZA JAG Shareholders Bittel Giles Investment CC SAKHISIWE GROUP (PTY) LTD Tabile Trade Rendani Transforce Transforce Blink Logic Shine the way 1065 CC

  • Clay Electrical
  • EXZA
  • JAG Shareholders
  • Bittel
  • Giles Investment CC
  • SAKHISIWE GROUP (PTY) LTD
  • Tabile Trade
  • Rendani
  • Transforce
  • Transforce
  • Blink Logic
  • Shine the way 1065 CC

Pre-Work Data captured for this Task

• Are you wearing correct PPE to perform the installation job?

  Yes

  No

  N/A

• Did you have key-based access to site? If not, grind off the main gate lock and return to Neocom offices as part of the scope of work

  Yes

  No

  N/A

• Is there a 3rd party gate to enter the property before the tower?

  Yes

  No

  N/A

• Is there a 3rd party lock?

  Yes

  No

  N/A

• Take 2 photos at 0.5m away displaying the locks in place from different angles if required, to include the lock body as well

  Media

• Please take a photo at 2.5m away to provide context, including gate and any other locking mechanism

  Media

• Is the site currently secured

  Yes

  No

  N/A

• Take a wide angle shot showing the gate entry point 2.5m away > Take a wide angle shot showing the gate entry point 2.5m away to include signage as well as hinges to show gate alignment

  Media

• Take a close-up photo 0.5m away from where installation will occur on the gate, from the outside

  Media

• Take a close-up photo 0.5m away from the inside

  Media

• Take a video of the area to be installed against showcasing quality of gate presently

  Media

• Is the site you have arrived at fit for installation against the main gate

  Yes

  No

  N/A

• Is there an ABLOY/CLIQ Key based lock on the main gate

  Yes

  No

  N/A

• What is the number engraved on the side of the lock

• What Keyless lock will be installed, enter BEAT Lock ID

• Does the lock number before installation match the housing cover which is engraved with the same number

  Yes

  No

  N/A

Data captured for this Task

• Was the lock installed with cup square bolt mounting with sheer nuts, mounting long plates are welded to the gate

  Yes

  No

  N/A

• The lock body housing was tac welded at the seams and treated with anti-rust agent once test confirmation that installation is working correctly against the gate installation

  Yes

  No

  N/A

• As per install guide, have you tac welded the lock housing plates together post install Have you applied anti rust agent to any welds and drilled holes on the gate prior to install

  Yes

  No

  N/A

• Take a close-up photo 0.5m away from where installation has occurred, from the outside

  Media

• Take a close-up photo 0.5m away from the inside

  Media

• Take a video of the area to which the housing was installed showcasing the installation done, quality of work, as well as manual opening and closing of the lock to show lock is freely working

  Media

• Connect to the lock, on access granted open the lock

  Yes

  No

  N/A

• Proceed to close the lock, Connect to the lock to resecure the lock

  Yes

  No

  N/A

• Connect to the lock, on access granted open the lock and leave it open

  Yes

  No

  N/A

Post-Work Data captured for this Task

• Have you resecured the site before leaving

  Yes

  No

  N/A

• Take a close-up photo 0.5m away showcasing the site is installed and lock is in secured state

  Media

• Takea photo 1m to 2.5 m away from the gate to showcase state of site

  Media