Induction RPAS - Mavic 2 Enterprise Series V1.1

• Name of RPA Pilot being inducted

• Conducted on

  Date

Aircraft

• Mavic 2 Enterprise - Uses the DJI Pilot App NOT DJI GO4
  Zoom Edition 905 g - Dual Edition 899 g - Advanced 909g
  Max Takeoff Weight 1100 g
  Max Service Ceiling Above Sea Level 6000 m
  Max Wind Speed Resistance 38 kph
  DEMO - unfold and fold arms
  DEMO - remove and replace props
  SD card slot - install and remove micro SD
  Also has 24G password-protected internal memory
  USB-C Port for firmware upgrade and retrieving data from internal memory
  Link button - to connect with remote control
  Vision system - Forward, Backward
  Downward vision system
  Lateral vision system - only operates in tripod mode
  Upward infrared sensing system
  Extended Port (to connect accessories)
  Maximum speed 72 kph in Sport mode 50 kph in P mode
  Aircraft Status indicators now on legs
  Do not fly in the rain
  Landing legs - Antennas

  

• 

• AirSence
  ADS-B out
  Warning Escalation:
  The first (or "lowest") level warning occurs when the manned aircraft is detected. All detected aircraft will be displayed in the app (up to 10 aircraft at a time). Please pay attention to ensure flight safety.
  The second (or “middle”) level warning occurs two kilometers away from the manned aircraft. Please pay attention to avoid any hazards.
  The third (or “highest”) level warning occurs one kilometer away from the manned aircraft. Please avoid the manned aircraft immediately.
  

  

• Aircraft Status Indicator Status
  

  

• 

• Mavic 2 Enterprise RPA

• Attach the gimbal cover when not in use.
  1) Hold the gimbal in place and insert gimbal clamp between the aircraft and the gimbal.
  2) Make sure the hooks on the Gimbal Protector are locked in the grooves of the aircraft, then lower the Gimbal Protector over the gimbal and secure with the buckle. The buckle will click when it is securely attached.
  Unlike the Mavic Pro the Enterprise must not be turned on with the gimbal cover in place.
  
  

  

• Gimbal Lock and Camera Guard

• Modular Accessories
  Accessories are controlled through the Pilot App
  
  

  

• Modular Accessories

Controllers

• Remote Control

• Remote Control 'Smart Controller'
  Battery level check
  Turn on and off
  C1, C2 and 5D buttons
  C3 - confirm button when not connected to RPA
  Return to Home button
  Intelligent Flight Pause Button
  Gimbal control dial
  Zoom adjustment dial (zoom) EV adjustment (dual)
  Video record button
  Still picture button
  Removable sticks and storage
  Flight Mode switch - S - P - T
  Antenna positioning and lock
  Speaker - Microphone
  SD Card
  HDMI
  USB C - fast charger
  

  

• Smart Controller

Power System

• Intelligent Flight Battery
  A capacity of 3850 mAh, a voltage of 15.4 V, and a smart charge/ discharge functionality
  DO NOT allow the batteries to come into contact with any kind of liquid. If the inside of the battery comes into contact with water, chemical decomposition may occur, potentially resulting in the battery catching on fire, and may even lead to an explosion.
  Do not drop battery
  Battery level check
  Turn on and off - only remove and connect to aircraft when battery switched off
  Demo - removal and connection to Mavic
  Don't charge straight after flight when battery is still hot
  Be careful to keep the power connector clean from dirt and fluff
  The battery will only charge when the temperature is between 5°C and 40°C
  Sleep Mode: To save power, the battery will cut off power supply and enter sleep mode after 20 minutes of inactivity
  Discharge is set to start after 10 days (countdown resets if battery check button is pressed)
  Discharging automatically stops at around 65%
  Heating batteries - auto heat if turned on in aircraft under 6 degrees. Manual hold power button for 5 seconds and will heat to 8-10 degrees
  Approximately 20 -30 minutes flight time
  Charging time 90 minutes

  

• 

• Battery Level Indicators

  

• Battery Protection LED Display

  

• Battery

• Plugs directly to battery or hub
  Tucked away controller charging cable
  

  

• 4 batteries in sequence
  Charges the battery that has the most power first
  Plug charger into hub
  Plug battery into hub

  

• Works on individual batteries or the hub

  

• Mavic Battery to Power Bank Adapter
  Used to charge controller and iPad using USB connector
  Plug onto battery
  Power on battery to operate
  OK to use remaining power in batteries after flight
  Battery will automatically turn off when power gets low

  

• Battery case (Separate purchase)
  Charges up to 4 batteries and 1 flight controller simultaneously
  Designed to work with generators, inverters and other “alternate” sources.

  

• Power Systems

Camera

• THERMAL CAMERA on M2E Dual
  Sensor Resolution 160×120 NIL Zoom
  Photo Format: JPEG
  Video Format: MP4, MOV ***********************************************
  VISUAL CAMERA on M2E Dual
  Sensor 1/2.3" CMOS; Effective pixels: 12M
  8 x Digital Zoom
  Photo Format: JPEG Video Format: MP4 ************************************************
  Visual Camera on M2E Zoom
  Sensor 1/2.3" CMOS; Effective pixels: 12M
  2 x Optical Zoom, 3 x Digital Zoom
  Photo Format: JPEG , DNG (RAW) Video Format: MP4, MOV ************************************************
  THERMAL CAMERA on M2E Advanced
  Sensor Resolution 640×512 16 x Zoom Accuracy of Thermal Temperature: Measurement: ±2℃ or ±2%, whichever is greater
  Photo Format: R-JPEG
  Video Format: MP4 *********************************************
  VISUAL CAMERA on M2E Advanced
  Sensor 1/2" CMOS; Effective pixels: 48M
  32 x Digital Zoom
  Photo Format: JPEG Video Format: MP4

  

• Camera

Ancillary Items

• Case holds standard Mavic equipment (Photo is example only)

  

• Portable Cases are available but not with the case
  Should be used to protect the Mavic and controller when transporting in a backpack. Separate purchase.

  

• Cases

• Propeller Guards can be purchased separately
  Always use when flying indoors
  Demo - connect and disconnect
  

  

• Propeller Guards

• Micro SD Card Holders
  READY holder means cards are available for use
  USED holder means cards have images yet to be transferred for records
  HEADQUARTER holder is used to ransfer cards to and from the search HQ if needed
  Also contains micro to SD card adaptor
  Be careful, only apply light pressure on tab when removing cards

• Micro SD Cards
  10 x 32GB U3 cards are provided in the Mavic kit
  Change the micro SD card for every flight
  

  

• Image handling

• Comments:

• The current (as at this induction date) Mavic 2 Enterprise manual is available at this link
  https://www.dji.com/au/downloads/products/mavic-2-enterprise Advanced Model:
  https://www.dji.com/au/mavic-2-enterprise-advanced/downloads

• Induction conducted by

  Sign