PEERLESS PRODUCTS WINDOW WATER TEST - INSTALL CHECK

• Document No.

• Audit Title

• Client / Site

• Conducted on

  Date

• Prepared by

• Location
  Address

• Personnel

• PEERLESS JOB NAME

• INSTALLER/CUSTOMER NAME - COMPANY

TYPICAL SUBSILL RECEPTOR EXTERIOR

• WEEPS DRAIN OPEN AND CLEAR OF DEBRIS

  Yes

  No

  N/A

• FREE OF GAPS IN WEATHERPROOFING AROUND SUBSILL/RECEPTOR THAT ARE CLEARLY NOTICEABLE

  Yes

  No

  N/A

• WEEP HOODS INSTALLED

  Yes

  No

  N/A

• IS THE EXPOSED JOINT OF MALE/FEMALE JOINT LOCATION SEALED AND TOOLED

  Yes

  No

  N/A

• IF VERTICLE MULLIONS ARE USED, WAS THE MULLION SET IN POOL OF SEALANT AND TOOLED, AND SEALANT APPLIED NEXT TO THE VERTICLE BULB AND ANY SQUISH OUT TOOLED

  Yes

  No

  N/A

TYPICAL RECEPTOR SUBSILL

• ARE JAMBS SQUARE AND NOT BOWED

  Yes

  No

  N/A

• IS SUBSILL RECEPTOR SET SQUARE AND PLUMB WITHIN THE OPENING

  Yes

  No

  N/A

• END DAMS SEALED CORRECTLY

  Yes

  No

  N/A

• RECEPTOR SET IN POOL OF SILICONE ON SUBSILL AND TOOLED CLEAN

  Yes

  No

  N/A

• WAS SEALANT APPLIED IN SEALANT TRACK OF SUBSILL FOR THE WINDOW TO SIT IN

  Yes

  No

  N/A

• WAS RECEPTOR CLIP SET IN POOL OF SEALANT ON THE SUBSILL AND 8" UP ON THE CLIP

  Yes

  No

  N/A

• WAS SEALANT TOOLED AROUND THE PEREMITER OF RECEPTOR CLIP TO SUBSILL JOINT

  Yes

  No

  N/A

MALE - FEMALE WINDOW JOINTS

• IS THE EXPOSED JOINT OF MALE/FEMALE JOINT LOCATION SEALED AND TOOLED

  Yes

  No

  N/A

• WAS A CONTINOUS BEAD OF SEALANT APPLIED ON BOTH MALE LEGS ON THE LEADING AND TRAILING EDGES OF MALE LEGS

  Yes

  No

  N/A

VERTICAL 3 PIECE MULLION

• WAS PRESSURE PLATE SET IN POOL OF SEALANT ON THE SUBSILL AND TOOLED

  Yes

  No

  N/A

• WAS SEALANT APPLIED ALONG SIDE OF BULB VINYL 8" UP FROM BOTTOM AND COVER INSTALLED

  Yes

  No

  N/A

• WAS SEALANT APPLIED TO BOTTOM OF COVER AND TOOLED AROUND THE PROFILE

  Yes

  No

  N/A

NAIL FIN FLASHING

• WAS SEALANT APPLIED TO FULL PERIMETER OF THE BACKSIDE OF WINDOW FIN

  Yes

  No

  N/A

H-MULLION W/O SUBSILL

• WAS MULL CLIP ANCHORED THROUGH RECEPTOR AND INTO SUBSTRATE TO CARRY THE LOAD OF THE H-MULL

  Yes

  No

  N/A

• WAS H-MULL PROFILE SEALED BEFORE FASTENING THE END DAM

  Yes

  No

  N/A

• IS H-MULL FACE SEALED AT THE BUTT JOINT TO RECEPTOR AND TOOLED

  Yes

  No

  N/A

• IS WINDOW SET (BOTH TOP AND BOTTOM WINDOW) INTO A CONTINOUS BEAD OF SEALANT IN BOTH INTERIOR AND EXTERIOR TRACKS

  Yes

  No

  N/A

ZERO MULLIONS

• SEALANT IS APPLIED 8" UP FROM BOTTOM ALONG MIDDLE OF MULLION

  Yes

  No

  N/A

• CONTINOUS BEAD OF SEALANT IS APPLIED TO EDGES OF ZERO MULL AND TOOLED CLEANLY AT WINDOW TO WINDOW JOINT.

  Yes

  No

  N/A

WINDOW WITH TRIM SETS - NO SUBSILL OR RECEPTOR

• WAS WINDOW SET ON U-SHIMS WITH BACKER ROD UNDER THE EXTERIOR LEG

  Yes

  No

  N/A

• WAS SEALANT APPLIED OVER TRIM FASTENERS UNDER TRIM CAP

  Yes

  No

  N/A

• SEALANT APPLIED AND TOOLED AROUND ENTIRE EXTERIOR OF WINDOW TO WALL JOINT

  Yes

  No

  N/A

PANNING

• MITERED EDGES OF PANNING PROFILES SEALED WHILE ASSEMBLY AND SQUEEZE OUT TOOLED CLEANLY

  Yes

  No

  N/A

• SEALANT FACE APPLIED ON THE JAMB TO SILL JOINT OF THE PANNING, TOOLED CLEANLY

  Yes

  No

  N/A

• PANNING INSTALLED SQUARE AND PLUMB, USING CUSTOMER SHIPS FOR PROPER SPACING

  Yes

  No

  N/A

• SEALANT APPLIED TO AREAS WHERE FASTENERS ARE USED TO ATTACH PANNING TO WALL CONDITION

  Yes

  No

  N/A

• SEALANT APPLIED TO EXTERIOR JOINTS OF THE PANNING SET TO WALL CONDITION, AND TOOLED CLEANLY

  Yes

  No

  N/A

• SEALANT APPLIED TO INSIDE FACE OF PANNING FOR THE WINDOW TO COMPRESS AGAINST AND ANY SQUISH OUT TOOLED CLEANLY

  Yes

  No

  N/A