Portable building ID and Number of Bays

  • Cabin ID

  • Number of bays

  • Purpose of Report is to Verify that the electrical installation for the portable building complies with BS 7671:2008 and is in a satisfactory condition for Hire or Sale

Methods of Protection against Electric Shock

  • BOTH BASIC AND FAULT PROTECTION - SELV

  • BASIC PROTECTION-Insulation of live parts

  • BASIC PROTECTION - Barriers or Enclosures

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    Presence of earthling conductor

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    Presence of circuit protection conductors

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    Presence of protective bonding conductors

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    Presence of supplementary bonding conductors

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    ADDITIONAL PROTECTION
    Presence of residual current device(s)

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    ADDITIONAL PROTECTION
    Presence of supplementary bonding conductors

  • FAULT PROTECTION - AUTOMATIC DISCONNECTION OF SUPPLY
    ADDITIONAL PROTECTION
    Choice of setting of protective and monitoring devices (for fault and/or overcurrent protection)

Prevention of mutual detrimental influence

  • Proximity of non-electrical services and other influences

Identification

  • Presence of diagrams, instructions, circuit charts and similar information

  • Presence of danger notices and other warning notices

  • Labelling of protective devices, switches and terminals

  • Identification of conductors

Cables and Conductors

  • Selection of conductors for current-carrying capacity and voltage drop

  • Erection methods

  • Routing of cables in prescribed zones

  • Cables incorporating earthed armour or sheath, or run within an earthed wiring system, or otherwise adequately protected against nails, screws and the like

  • Additional protection provided by 30 mA RCD for cables concealed in walls (where required in premises not under the supervision of a skilled or instructed person)

  • Connection of conductors

  • Presence of fire barriers, suitable seals and protection against thermal effects

General

  • Presence and correct location of appropriate devices for isolation and switching

  • Adequacy of access to switchgear and other equipment

  • Particular protective measures for special installations and locations

  • Connection of single-pole devices for protection or switching in line conductors only

  • Correct connection of accessories and equipment

  • Selection of equipment and protective measures appropriate to external influences

  • Selection of appropriate functional switching devices

  • FUNCTIONAL TEST

  • COMMENTS / REMEDIAL WORK COMPLETED BEFORE INSPECTION

This Inspection has been carried out in accordance with BS 7671:2008 (IEE Wiring Regulations) amended to __________ . Cables concealed within trunking and conduit, or cables and conduits concealed under floors, roof spaces and generally within the fabric of the building or underground have not been inspected.

  • NEXT INSPECTION
    This unit should be next inspected not more than 12 months from the date of the latest Electrical Installation Certificate, Periodic Inspection Report or Pre Delivery Inspection & Testing Report. Should the unit be relocated before this period a new report will be required

  • Date of next inspection

  • Signature For or On behalf of Portable Offices (Hire) Ltd

  • Counter Signature For or On behalf of Portable Offices (Hire) Ltd

  • DATE OF INSPECTION

  • This unit will need to be tested in accordance with BS 7671 once a supply is connected. This inspection and testing should be carried out by a competent person and a relevant report produced

TEST RESULTS

  • Unit Number:

  • Location:

  • Number of ways:

Main Switch or Circuit Breaker

  • Type BS (EN)

  • Rating (A)

  • Voltage Rating (V)

  • Nominal Rating Uo/U

  • Residual operating current at I^ n

  • Method of protection against fault protection:

  • Equipment Vulnerable to Testing

  • Number of smoke detectors:

Details of Incomer

  • Acceptable system type(s)

  • Maximum tolerable upstream earth fault loop impedance Zt in ♎

  • Maximum tolerable fault current in kA

  • Operating times of associated RCD 1*I^N in ms

  • Operating times of associated RCD 5*I^N in ms

Test Instruments

  • Multi-functional tester serial number:

  • Are you using other test equipment

  • Enter type and serial number of test equipment used

  • Main equipment bonding to extraneous conductive parts

  • Main protective bonding conductors- Material

  • Main protective bonding conductors- CSA (mm2)

Schedule of Circuit Details and Schedule of test results

  • Is there a Circuit Designation?

  • Circuit designation
  • Circuit Designation

  • Type of wiring

  • Reference method

  • Number of points served

  • Circuit Conductors :csa - Live (mm2)

  • Circuit Conductors :csa - C.P.C (mm2)

  • Max Disconnection time permitted (BS7671)

  • Over current protection devices - BS (EN)

  • Over current protection devices - Type number:

  • Over current protection devices - Rating (A)

  • Max Zs @ 80%

  • Test result -Continuity ♎ ALL CIRCUITS - R1 + R2

  • Test result -Continuity ♎ ALL CIRCUITS - R2

  • Test result -Continuity ♎ ALL CIRCUITS - Ring final circuits only (measured end to end) r1 (line)

  • Test result -Continuity ♎ ALL CIRCUITS - Ring final circuits only (measured end to end) r2 (cpc)

  • Test result -Continuity ♎ ALL CIRCUITS - Ring final circuits only (measured end to end) r n (neutral)

  • Insulation Resistance - Live / Neutral (M♎)

  • Insulation Resistance - Live / Earth (M♎)

  • Insulation Resistance - Neutral / Earth (M♎)

  • Polarity

  • Zs - Measured Zs

  • RCD - at 1 x (Ms)

  • RCD - at 5 x (Ms)

  • Codes used for type of wire A = PVC / PVC Cables B = PVC Cables in Metallic Conduit C = PVC Cables in non Metallic Conduit D = PVC Cables in Metallic Trunking E = PVC Cables in non Metallic Trunking F = PVC / SWA Cables G = XLPE / SWA Cables H = Mineral Insulated Cables O = Please see below

The templates available in our Public Library have been created by our customers and employees to help get you started using SafetyCulture's solutions. The templates are intended to be used as hypothetical examples only and should not be used as a substitute for professional advice. You should seek your own professional advice to determine if the use of a template is permissible in your workplace or jurisdiction. Any ratings or scores displayed in our Public Library have not been verified by SafetyCulture for accuracy. Users of our platform may provide a rating or score that is incorrect or misleading. You should independently determine whether the template is suitable for your circumstances. You can use our Public Library to search based on criteria such as industry and subject matter. Search results are based on their relevance to your search and other criteria. We may feature checklists based on subject matters we think may be of interest to our customers.