Information
-
Prism Dive Number
-
Location
-
Conducted on
-
Diver
-
Buddy
1. Check H-Plate / Harness / BC for Wear, Damage or Missing Parts
-
A. H-Plate
-
B. Harness (W)
-
C. Fabric (W)
-
D. Inflator / Alt. Air Source (O)
-
E. Dump Valve(s) (O, W)
-
F. Removable Weight Pockets (W, I)
-
G. Fastening Clips (W)
2. Inspect Counterlungs
-
A. Fabric (W)
-
B. Drains (O)
-
C. Threaded DSV/BOV Assembly Rings (W)
-
D. Breathing Hoses, Oetiker Clamps,<br>+ O-Rings (W)
-
E. O2 Addition Valve (I, O)
-
F. Automatic Diluent Valve (ADV) (O)
-
G. Over-Pressure Valve (OPV) (O)
3. Inspect DSV/BOV Breathing Hoses
-
A. Hoses
-
B. Oetiker Clamps (W)
-
C. O-Rings (W)
-
D. Inhalation Hose Mushroom Valve<br>(only on inhale hose for DSV supplied systems)<br>(O, W)
4. Inspect DSV/BOV
-
A. Shut-Down/OC Assembly (O)
-
B. Water Drain (O)
-
C. Mouthpiece, Zip-Tie
-
D. DSV/BOV Exhalation Mushroom Valve (O,W)
-
E. Inhalation Hose Mushroom Valve (only on<br>inhale side of BOV) (O, W)
5. Inspect Regulators + Hoses
-
A. 1st Stages (W)
-
B. Pressure Relief Valves
-
C. LP Hoses + Connectors (W)
-
D. HP Hoses + Connectors (W)
-
E. Diver Installed Gas Supply Hoses<br>(if installed)
-
F. Pressure Gauges
6. Inspect Wiring
-
A. Heads Up Display (W)
-
B. Wrist Display (W)
7. Battery Compartment, Batteries + O-Rings
-
A. Solenoid Batteries (I)
-
B. Heads Up Display Battery (I)
-
C. O-Rings (2) (W)
-
D. Cover, Cover Latches + Keepers (O,W)
8. Solenoid Operation
-
Solenoid Operation (O)(If proceeding<br>immediately to assembly and operational<br>checks, you can skip this step.)
9. Inspect Head Assembly
-
A. Red CO2 Seal (I, W)
-
B. Head To Bucket O-Rings (2) (W)
-
C. O-Ring Seats (W)
-
D. Latch Keeper (W)
-
E. Nut Bars, Head Bolts, Head Cover Bar +<br>Head Cover (W, I)
10. Oxygen Sensors
-
A. 3 Oxygen Sensors + Sensor Holders Installed (I)<br>
-
B. Oxygen Sensor Wiring Harness (I)
-
C. mV Readings Within Range(O)<br>(8.5 mV to 14 mV in air)
11. Bucket Assembly
-
C. 1 Moisture Pad (I)
-
B. Latches (3) (W, O)
-
A. Basket Compression Spring + Pad(I)
12. Basket Assembly
-
D. Top + Bottom Foam Pads (I)
-
B. Center Tube O-Ring (I)
-
C. Top + Basket Threads Clean (O)
-
A. Check Mesh (W)