Title Page
-
Site conducted
-
Conducted on
-
Prepared by
-
Location
Overall
-
Correct Slab/glass hinge
-
Correct Sweep
-
Glazing Correct
-
Correct Jamb
-
Jamb Fasteners
-
Reveal 1/8 +/- 1/16
-
Screws for composite
-
Staples in top half of header
-
Location across jamb
-
Quantity
-
Flush or inset
-
Jamb Damage
-
Security Plate
-
Sidelite Position
-
Construction
-
Positioned Correctly
-
Jambs/header aligned
-
(4) Staples
-
Jambs/header straight
-
Jambs/header good
-
Stop: Straight, good
-
Backset
-
Correct 2 3/8" or 2 3/4"
-
Hinges
-
Flush w/jamb
-
Packaging Door Clip
-
Correct Hinge
-
Matching color screw
-
(2) Staples
-
Door #10 x1" screws
-
Jamb #10 X 5/8" screws
-
Sill Fasteners
-
Jamb (1) screw hole empty next to weather strip
-
Correct Sill
-
Screws for Composite
-
(2) hinge protectors
-
Quantity
-
Flush or inset
-
Jamb Damage
-
Handle
-
Bottom Skid Board
-
(2) Staples ea. Side
-
Header
-
Labels
-
Brick Mold
-
Miter fastened correctly
-
Offset:
-
Joint Gap < 1/16
-
Leg/Header Flush
-
Legs 7) nails
-
Packaging
-
Outswing 1/4"
-
Header (4) nails
-
Skirts fastened w/(6) staples
-
No nails protruding
-
Door Strapped
-
Offset consistent L/R
-
Door Stretched wrapped
Observations & Comments
-
Pre-Finished Quality
-
Cut Out Tolerance Check
-
Height
-
Width
-
Spec is 1 inch taller and 1 inch wider than glass size
-
+/- 1/16"
-
Cut Out
-
Cut Out Centering Check (+/- 1/16")
-
Measured Distance A-D
-
Measured Distance B-C
-
Glazing
-
Cut out size 1" larger than glass +/- 1/8
-
Cut quality No Burrs or Jagged edges
-
Glass correctly oriented, set at base
-
Chip out: Must be covered by frame
-
of cut out and straight +/- 1/8"
-
Embossment showing <= 1/8"
-
Tempering info on Lower Corner if possible
-
Smooth fiberglass Cutout to witness
-
Bevels pointing to exterior side
-
lines/embossment look visually good
-
Glass free of scratches
-
Lite Frame
-
No sealant visible more than 1/8" x1/4" long max
-
No gaps: Frames to glass or Frame to Door
-
No raised corners
-
Make sure screw plugs are set and aligned properly
Door Fab
-
Jambs Checked
-
#1 Hinge prep jamb: 6 1/8" +/- 1/32"?
-
#2 Hinge prep jamb: 45 1/2"?
-
611/2"): Latch prep jamb 37 1/8" (8/0 32 1/8") +/- 1/32"?
-
4. Latch prep jamb: Latch prep jamb 68 1/8" (8/0 10 1/2") (8/0 58 1/8") +/- 1/32"?
-
5. Hinge depth: Hinge depth 0.094" +/- 0.015"?
-
7. Deadbolt Mortise
-
8. Latch Mortise
