SPC Emergency Light Testing V2

• SPC Emergency Light Testing BS-5266-1:2016

SPC Emergency Light Testing V2 Model Certificate for Verification of Existing Installations- Checklist and Report

• Site Address
  Address

• Responsible Person

• Inspection Date

  Date

Check of Categories and Documentation

• 4.2- Are plans of the system available and correct?

  Yes

  No

  N/A

• 6.7- Has the system been designed for the correct mode of operation category?

  Yes

  No

  N/A

• 6.7- Has the system been designed for the correct emergency duration period?

  Yes

  No

  N/A

• Clause 11- Is a completion certificate available with photometric design data?

  Yes

  No

  N/A

• Clause 11- Is a test book available and are the entires up to date?

  Yes

  No

  N/A

• Comments

• Please add pictures if applicable

  Media

Check of Design

• 4.1; 5.2.8- Are the correct areas of the premises covered to meet the risk assessment?

  Yes

  No

  N/A

• 5.2.8- Are all hazards identified by the risk assessment covered?

  Yes

  No

  N/A

• 5.2.8- Are there luminaires sited at the "points of emphasis"

  Yes

  No

  N/A

• 5.2.2- Is the spacing between luminaires compliant with authenticated spacing or design data?

  Yes

  No

  N/A

• 10.3; 10.7- if authenticated spacing data is not available for existing installations, are estimates attached and acceptable?

  Yes

  No

  N/A

• 5.2.9- Are the emergency exit signs and escape route direction signs correct and the locations of other safety signs to be illuminated under emergency conditions identified?

  Yes

  No

  N/A

• 6.1- Do all non-maintained luminaires operate on local final circuit failure?

  Yes

  No

  N/A

• 6.3- Is there illumination from at least two luminaires in each compartment?

  Yes

  No

  N/A

• 6.4- Are luminaires at least 2m above floor and avoiding smoke reservoirs?

  Yes

  No

  N/A

• 5.8.2.5;;6- Are additional luminaires located to cover toilets, lifts, plant rooms, etc?

  Yes

  No

  N/A

• Comments

• Please add pictures if applicable

  Media

Check of the quality of the system components and installation

• 6.7- Do the luminaires conform to BS EN 60598-2-22?

  Yes

  No

  N/A

• 6.7- Do any converted luminaires conform to BS EN 60598-2-22?

  Yes

  No

  N/A

• 6.7- Do luminaires have a suitable degree of protection for their location?

  Yes

  No

  N/A

• Clause 8- Does the installation conform to the good practice defined in BS 7671?

  Yes

  No

  N/A

• 8.2.1- For centrally powered systems, is the wiring fire-resistant?

  Yes

  No

  N/A

• 8.2.12- Are any plugs or sockets protected against unauthorised use?

  Yes

  No

  N/A

• 7.2- If a central power supply unit is used, does it conform to BS EN 50171?

  Yes

  No

  N/A

• 8.3.3- Are the test facilities suitable to test function and duration?

  Yes

  No

  N/A

• 8.3.3- Are the test facilities safe to operate and do not isolate a required service?

  Yes

  No

  N/A

• 8.3.3- Are the test facilities clearly marked with their function?

  Yes

  No

  N/A

• 8.3.3- If an automatic test system is installed, does it conform to BS EN 62034?

  Yes

  No

  N/A

• 10.7- Are the user's staff trained and able to operate the test facilities and record the test results correctly?

  Yes

  No

  N/A

• Clause 12- Does the system operate correctly when tested?

  Yes

  No

  N/A

• 10.7- Has adequate documentation been provided to the user?

  Yes

  No

  N/A

• 10.7- Is the user aware of action they should take in the event of a test failure?

  Yes

  No

  N/A

• 10.7- Are any deviations fully documented and are they still acceptable?

  Yes

  No

  N/A

• Action recommended or deviation to be reported:

• Comments

• Please add pictures if applicable

  Media

• Results of the inspection

• Signed. By signing you confirm all works comply with BS-5266-1:2016

  Sign

IA-04-21b