Vindex Systems MicroPoint PIDS VIN.Q.320

Site Details and Job Information

• VIN.Q.

• Site Address
  Address

• Client / Site

• Job Title_QVIN

• Conducted on

  Date

• Engineers and PM

• Prepared by

NOTE: Please read carefully before completing and signing this form. The following document will ensure that all necessary tasks that are the responsibility of the installer are completed by the Vindex Technician. Upon arrival at the site, the Commissioning Engineer will inspect the installation and set up parameters to certify that the work completed meets factory standards. This document will form part of the commissioning and handover process.

MicroPoint II Cable Installation

• MicroPoint cable installed on the fence line in accordance with Chapter 4 of the MicroPoint II Installation Manual.

  Date

• MicroPoint cable installed on swing gates in accordance with Chapter 4 of the MicroPoint II Installation Manual.

  Date

• MicroPoint cable properly terminated to ALL modules and dielectric grease applied in accordance with Chapter 5 of the MicroPoint II Installation Manual.

  Date

• Distance between cable ties securing the MicroPoint cable on the fence fabric does not exceed 9 inch (229mm) intervals.

  Date

• Each individual MicroPoint cable is calibrated per Section 4.2.4 of the Universal Installation Service Tool II (UIST II) Technical Manual.

  Date

Module Installation

• Processor Module II’s (PM II) are installed in accordance with Chapter 4 of the MicroPoint II Manual and site specific requirements.

  Date

• Link Unit II’s (LU II) are installed in accordance with Chapter 4 of the MicroPoint II Manual and site specific requirements.

  Date

• Termination Unit II’s (TU II) are installed in accordance with Chapter 4 of the MicroPoint II Manual and site specific requirements.

  Date

• Splice Units (SU) are installed in accordance with Chapters 4 and 5 of the MicroPoint™ II Manual and site specific requirements.

  Date

• A controller (RCM II, CM II, CM II-N, GCM II-HD, PSM, RPM II or SDK) are installed in accordance with job specific requirements.

  Date

• Relay Output Module II’s (ROM II) are installed in accordance with site specific requirements.

  Date

• Alarm Input Module II’s (AIM II) are installed in accordance with site specific requirements.

  Date

• The Communications line is grounded at the JB70A (which has an earth ground), in accordance with Chapter 4 the MicroPoint II Installation Manual.

  Date

Power and Communication Wiring

• Power Supplies are mounted and wired per job specific instructions.

  Date

• Wiring for DC power terminated at the feed point PM II(s) and/or any AIM II and ROM II per site specific requirements.

  Date

• RS422 communication cable is terminated at the feed point PM II and/or any AIM II and ROM II per site specific requirements.

  Date

• RS422 communication cable is terminated at the Controller per site specific requirements.

  Date

• All wiring from microwaves or auxiliary sensors to PM II(s) and/or AIM II’s Properly terminated per site specific requirements.

  Date

Control Room Equipment

• AC power available for the GCM II-HD, monitor, printer, power supplies and UPS system.

  Date

• Controller, AIM II's and/or ROM II's, UPS and/or other peripheral hardware mounted to end user's satisfaction.

  Date

• Universal Installation Service Tool II (UIST II) software installed on customer supplied computer.

  Date

• Printer connected to the GCM II-HD and paper installed.

  Date

• Cabling for the controller, monitor and printer, properly dressed to the end user’s satisfaction.

  Date

MicroPoint II Commissioning Information

• Processor Module II’s (PM II’s) are properly addressed per Section 5.2.4 of the MicroPoint™ II Manual and per site specific requirements.

  Date

• All cables have been calibrated.

  Date

• All Processor Module II’s (PM II’s) are communicating with the controller.

  Date

• All Relay Output assignments are made per site specific requirements.

  Date

• All auxiliary inputs have been assigned to the proper PM II, or AIM II per site specific requirements.

  Date

Enter the following Final Site Data values on the chart below for each PM II in the system.

• Processor Module II

PM II

• Processor Module II No.

• Volts DC at PMII - VDC

System Sign Off

Discrepancies/Notes

Sign Off

• By signing this document I certify that all the above tasks have been completed in accordance with the installation specification and a fully functional commissioning, inspection and testing have been completed.

• Vindex Systems Representative

  Sign

• Customer

  Sign

PIDS System Installation Information

• Date

  Date

• PIDS System

  Select GCM-II ROM-II x 3 PM-II X 8 LU-II X 7 TU X 0

  • GCM-II
  • ROM-II x 3
  • PM-II X 8
  • LU-II X 7
  • TU X 0

GCM-II

• IP Address

• Subnet Mask

• Default Gateway

• Passwords

Volts DC

• PM

• PM

ROM-II x 3

• IP Address

• Subnet Mask

• Default Gateway

• Passwords

Volts DC

• PM

• PM

PM-11 x 8

• IP Address

• Subnet Mask

• Default Gateway

• Passwords

Volts DC

• PM

• PM

LUX-II x &

• IP Address

• Subnet Mask

• Default Gateway

• Passwords

Volts DC

• PM

• PM

TU X 0

• IP Address

• Subnet Mask

• Default Gateway

• Passwords

Volts DC

• PM

• PM

PIDS Zone List

• Zones

Zone

• PM No.

• Cable

  Cable A

  Cable B

• Cell To/From or Beam

  Select To From Beam

  • To
  • From
  • Beam

• Beam Information

Zone Input/Output Test

• Zones

Zone

• Alarm Activation

  Yes

  No

• Relay Activation

  Yes

  No

• CCTV Activation

  Yes

  No

Commissioning Sign Off

• Engineer

  Sign

• Customer

  Sign