CFA Medium Pumper Quality Assurance Inspection

Information

Audit Title
Conducted on
Personnel, if different to list below
- Danny O'Neill
- Andrew Webb
- Karen Barnett
- Elliott Barnfather
- Ken Hare

Quality Insurance Inspection Medium Pumper Inspection

Country Fire Authority Fleet Services Department
Inspection No P16/
Appliance Manufacturer:
Brigade:
DMO:
- Bairnsdale
- Ballarat
- Cranbourne
- Geelong
- Horsham
- Kangaroo Flat
- Moe
- Mt Evelyn
- Seymour
- Shepparton
- Swan Hill
- Wangaratta
- Warrnambool
District
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
Date:
Time Commenced:
Time Completed:
Odometer at start
Odometer at finnish
Pump Hrs at commencement of inspection
Pump Hrs at completion
Appliance Details
Registration Number:
Rego plate photo
Cab Chassis Manufacturer and Model Number
Scania P310 (4x2) Crew Cab Chassis, Automatic Transmission. P310 DB 4x2 HNA (18600 kg)
Second Stage of Manufacture Plate/VASS for rear BA seating
Cab Chassis Vin: YS2P4X2000
Vin No photo
Raise cabin to check and record Tans and engine numbers;
Cab Chassis Engine Number:
Cab Chassis Engine Number photo
Allison Transmission serial number;
Auto trans serial number photo.
Record tyre make model and size;
Body Number/Date of manufacture:
Body manufacture plate photo (if fitted)
Fire Pump Manufacturer; GODIVA Prima P1B-4010
Fire Pump Serial No:
Pump serial number photo
CFA Radio Number: Serial No:
Aerial Identification Number

Cab Chassis;

1. Commencement of pumping;

It is recommended that initially the appliance be connected to the test well and be actually pumping during the general appliance inspection.

This shall ensure that the maximum pumping time is achieved for the overall inspection time available.
1.1 Connect appliance suction hoses.
1.2 Connect 65mm delivery hose to one of the side deliveries
1.3 Scania based appliance only: Open the valve on the hard suction.
1.4 With the appliance engine running operate the pump engagement switch in the cabin. The appliance should: Automatically “squat” mode by approximately 100mm (rear of the vehicle) with pump engagement. Automatically prime. Prime time in seconds: 20 sec
1.5 At the operating panel increase the engine speed with the electronic throttle on the pump panel.
1.6 Open the 65mm delivery valve.

2. Cab/Chassis

2.1 Cabin access handles: Front doors: Left side of doorway Right side of doorway Rear doors: Left side of doorway Right side of doorway Rear Internal handrailing : Clearance between centre cabin handrail & front rear handrail (no flexing within handrail)
2.2 All interior lighting – Check operation at all door controls.
2.3 All dashboard driving instrumentation
2.4 Cab Chassis Radio (Scania Radio)
2.5 Electric Cabin Windows :- Front drivers and passenger windows Rear drivers and passenger windows
2.6 Remote Drivers and Passenger Rear Vision Mirrors
2.7 Cab Chassis Amber Hazard Lights
Automatic Transmission Controls 2.8 Transmission Retarder on vehicle console (Lever operated controls)
2.9 Engine Low Oil / High Temperature Warning Light
2.10 ABS Warning Light
2.11 Air Conditioning System Rear roof mounted air conditioning outlets (for rear of cabin)
2.12 Five (5) retractable lap/sash seat belts Red Seat Belts fitted Front Seats Red Seat Belts fitted to Rear Seats
2.13 Two (2) rear “Bostrum” B.A. seats Check operation of the new “Bostrum” B.A. seats VASS Certificate for B.A. seat installation
2.14 One (1) centre rear individual seat with adjustable headrest
2.15 Cabin floor matting to be suitably secured
2.16 General cleanliness of cabin.
All switches - check the operation of
2.17 Park lights
2.18 Head lights
2.19 Tail lights. At Bumper level Top of rear bodywork
2.20 Stop lights
2.21 Indicators :- Driver’s side (front and rear). Passenger’s side (front and rear).
2.22 Fog lights including decal (Parkers must be on)
2.23 Back up lights including reversing buzzer.
2.24 Emergency Switch (Centre Dash Console) “Emergency Response” switch No change to Emergency Lights with park brake on. Class 1 switch indicator lights to stay on. All switches labelled. “Beacons” Switch “Flashing Headlight” Switch “Hazards” Switch
2.25 Front “Britax/Code 3” LED Beacons Nearside : Mini Light Bar (Flashes Red/Blue) Offside : Mini Light Bar (Flashes Red/Blue) Rear “Britax/Code 3” LED Beacons Nearside : Mini Light Bar (Flashes Red/Blue) Offside : Mini Light Bar (Flashes Red/Blue) Beacons Flash Pattern is All Red then All Blue
2.26 Front Red/Blue “Britax” LED Hazard Lights (Between Speakers) Front Red/Blue “Britax” LED Hazard Lights (Outside Speakers) Front Corner Red/Blue “Britax” LED Hazard Lights Front Wheel Arch Red/Blue “Britax” LED Hazard Lights Hazard Flash Pattern is All Red then All Blue
2.27 Flashing headlights (To cancel with parkers )
2.28 Rear Red/Blue “Britax” LED Hazard Lights (At Bumper Level) Rear White Reversing lights flash
2.29 “Central Locking” Switch for bodywork roller shutters (On Centre Console) Central locking releases once ignition is “ON”. Will only lock in ACCESSORIES position
2.30 “Low Water” Alarm Test Switch (On Centre Console) “LOW WATER” Test Function only operates in ACCESSORIES
2.33 “PTO” Engage Amber Rotary Switch (On Centre Console) OFF / ON & PTO / ENGAGE label Backlighting: PTO switch panel must be back lit.
2.31 “Federal Signal” Wireless “Visbeam” Search Light on roof of crew cabin Wireless Remote Control (on front console)
2.32 Front of Vehicle One (1) “Britax/Code 3” Sign” Rumblers Rumblers controls on the Siren Panel
2.33 “PTO” Engage Amber Rotary Switch (On Centre Console) OFF / ON & PTO / ENGAGE label Backlighting: PTO switch panel must be back lit.
2.34 “PTO” Engage Green Warning Light “OK TO PUMP”
2.35“LOW WATER” Amber Warning Light with O/S Amber Strobe fitted at rear of bodywork with siren
2.36 “LOCKER OPEN” Red Warning Light
2.37 “MAST/GANTRY RAISED” Red Warning Light
2.38 Battery Isolation Switch (Battery Guard switch fitted to dash)
2.39 Siren System (Code 3 Banshee) :- Wail/Yelp/Mix facilities P.A. facilities. Siren microphone located on top of dash (At the front of Siren Control)
2.40 Reverse Camera Screen & Controls If Reversing Camera is off & Reverse selected the camera will turn ON.
2.41 CFA Radio operation.
Relay wired through vehicle’s ignition switch
One (1) clip fitted for radio microphone (Located on corner of dash)
Plastic Inspection Caps in roof lining where radio bases located.
2.42 Two (2) CFA Radio speakers (Front cabin – centre, forward facing, middle cabin & Rear cabin – centre rear wall)
2.43 Four (4) LED Map lights Front (passenger & driver) Rear (mounted over rear doors : nearside & offside) Map lights wired through the ignition (not hard wired)
2.44 “Air Horn” operation.( Air Actuated Type Horn) Air Horn activated by foot switch on left-hand side of steering wheel
2.45 Two (2) Portable Radio Charger Base & Holder (CFA supplied) located in the rear centre console
2.46 Two (2) bank portable radio holder (with no charging facilities) in Front Area (Front of Helmet Console) c/w elastic strap and hand tag.
2.47 Two (2) bank portable radio holder (with no charging facilities) on the inside of the rear cabin doors (c/w elastic strap and hand tag.)
2.48 Dash mounted white board (front passenger) c/w red & blue pen markers & two (2) pen clips Velcro material to be used on the mounting brackets & back of whiteboard
2.49 24 hour Digital Clock in Front Overhead Console
2.50 Cabin Water Tanker Level Indicator to be located in the overhead console (in the centre) next to the Digital Clock
2.51 2.52 2.53 Cabin centre console
Document holder located between drivers and front passenger seats complete with :- Three (3) partition centre vertical compartment with lid and retaining elastic strap. Helmet Holders c/w Velcro straps on each side of the centre front compartment.
One (1) Rear Open Area Console Arrangement. Rear corners of the open area to be chafer at 45 degrees
Two (2) Cabin Compartments fitted with lids & elastic straps fitted on lids(behind front passenger & driver seats)
Cabin Compartments to be fully lined with 2mm insertion rubber
Rear passenger side compartment to have a side cut out for Thermal Imaging Camera TIC
Rear drivers side compartment to have a side cut out for access to internal cabin handrail
2.54 Helmet Holders fitted on each inner rear door c/w elastic straps.
2.55 Two (2) Helmet Holder c/w elastic strap under rear seat (outer side)
2.56 One (1) rechargeable “Pelican” portable torches (located near the front passenger seat)
2.57 Five(5) small battery powered “Pelican” flashlights (supplied loose)
One (1) small battery powered “Pelican” flashlight (located on front centre dash area)
2.58 Maglight Torch Bracket (Left Hand Side of Passenger Seat)
2.59 Drink holders
Two (2) drink holders for front passenger and driver.
Six (6) drink holders for rear passengers (between rear seats)
Drain holes fitted in base of drink holders
2.60 Blankets.
Three (3) blanket compartments located behind and under rear seats for the stowage of five (5) fire blankets
One (1) blanket located in each rear corner of the cabin
Three (3) blankets under the rear seats with front elastic cable & three (3) “Yellow” pull tags
2.61 Bluetooth hands free kit
Bluetooth Hands Free Kit shall be fitted in the cabin
Bluetooth speaker shall be located in the centre of cabin roof, next to the CFA radio speaker
“Call receive/end” button for the Bluetooth shall be mounted in the front area of the cabin
2.62 One (1) 24 volt electrical inlet plug located in the rear centre open area (24 VOLT OUTLET)
2.63 Class 1 (Can Bus) diagnostic plug location in the front area of cabin
2.64 Electrical equipment within cabin located under rear centre open area
Electrical compartment shall be fully vented
Document Holder between front seats to include
2.65 Cab Chassis Manufacturers Operating Manual.
2.66 Cab Chassis Manufacturers Warranty Book.
2.67 CFA Logbook.
2.68 Appliance Operating Manuals (4 copies).
2.69, 2.103 & 2.104 Brigade Name Decals (2) door and 1x visor decal 100mm

Decals inside the cabin

2.70 Five (5) “Seat Belts Must Be Worn” Decals
2.71 Four (4) “Cabin Exit” (Step Backwards) Decals on inside of cabin doors
2.72 “Vehicle Weight and Dimensions" Decal
Overall Length Dimension
Overall Width Dimension
Overall Height Dimension
Allowable G.V.M.
Allowable Front Axle Loading 6.00T
Allowable Rear Axle Loading 9.00T
G.V.M. : 15.00 Tonne
2.73 “Aerial I.D” Decal in front area of cabin
2.74 “First Aid Kit” Decal (Upper left corner of the windscreen)
2.75 “Fog Lights” Decal (located on the cabin fog light switch)
2.76 “Hazchem Scale” Decal (Upper left corner of the windscreen)
2.77 “Circuit Breaker Identification” Decal (With electrical equipment)
2.78 “No Smoking” Decal (Overhead Console)

Cabin Tilt Arrangement: WARNING: If the fire pump is running beware of rotating drive shafts.

2.79 Locking mechanism
2.80 Limit switches
2.81 Cabin lift pump operation. Upwards. Downwards.
2.82 Cabin up position support stay (Colour Coded “Yellow”).
2.83 Cabin Tilt Instructions Decal
2.84 Two towing locations at front of vehicle with single pin arrangement
2.85 Pre-cleaner on the air intake tube (Aluminium Mushroom Cap with Ember Screen)
2.86 Steel/Aluminium piping from air intake to turbo-charger.
2.87 Air intake filter housing located in the front offside wheel arch area (Non-Metal housing)
2.88 Rust prevention protection paint on chassis rails (Grey Painted Chassis Rail)
2.89 White LED step lights on all steps operating when the door is opened. Rear cabin steps to be fitted with suitable white LED light.
2.90 Spot convex rear view mirror on passenger’s side.
2.91 Brake lines to be fitted with (Approved fire resistant lagging material)
2.92 Fuel lines (Plastic lines to be protected within chassis rails)
2.93 100 Ampere Alternator (100 ampere x 24 volt = 2,400 watt capacity)
2.94 Check Cabin Insulation under Cabin
2.95 Fuel Filter
2.96 Check tyre valve extension tubes are stainless steel/brass.
Batteries
3.47 Batteries replaced with four (4) Century N70ZZ batteries
3.49 Standard Scania battery carrier (under nearside rear steps)

Decals on the cabin exterior

2.97 Tyre Inflation Pressure (725 kPa) at all wheel arches
2.98 Watch Your Step (each of the four door sills)
2.99 Red CFA Logo on white background on the outside “B” pillar.
2.100 Aerial Identification Number on the cabin roof.
2.101 CFA 200mm Wide Red / Yellow Checker Reflective Striping along the doors (No black pin striping)
2.102 Lime-Green 150mm high “FIRE” signs on the lower part of the front cabin doors No “FIRE” signs on front of cabin
2.105 “Lime-Green” Reflective Striping located as follows :- Front of cabin (front grill) Front of cabin (Sunvisor) Outline the complete crew cabin (front edge of cabin) Back of side rear vision mirrors Inside cabin doors

Miscellaneous Equipment

2.106 Front Cabin Access Steps colour coded “Yellow”. Rear Cabin Steps colour coded “Yellow”. Rear Cabin Steps, fold-out arrangement, activated by doors.
2.107 All cabin steps fitted with “Lime-Green” reflective striping on the outside edges
2.108 Vertical Exhaust fitted on nearside of vehicle Heat shield material fitted to exhaust pipe Exhaust tail pipe fitted with weather proof cap
2.109 Tinted side windows of the Scania crew cabin
2.111 24 Volt Jump Start Plug :-
Nearside of body c/w 6mm spacer and decal
Offside of body c/w 6mm spacer and decal
6.0 metre long Anderson lead with plugs (each end)
2.112 Upgraded front grill lift up panel struts. Scania 2031866 (250 N) Gas Strut fitted. (Re-gassed to 400 N)
2.113 Steel encircling loop fitted around chassis driveshaft
2.114 Separate air tank within the chassis rails for auxiliary equipment
2.115 One (1) USB Power Outlet (Passenger Side)
2.116 One (1) Additional 24 volt Outlet (Passenger Side)

Fire Fighting Bodywork

Body General :-

NOTE; Spare wheel will be delivered to DMO direct from Scania Australia.
3.1 Sub-Frame Arrangement.
Mounting Brackets and Chassis Locking Plates.
Pump driveline arrangement
Under body inspection
Tank overflow

Locker doors

3.2 Roller doors, Check operation of all roller doors:
NS 1 (Front nearside locker)
Roller Shutter Serial No.
NS 2 (Wheel arch nearside locker)
Roller Shutter Serial No.
NS 3 (Rear nearside locker)
Roller Shutter Serial No.
Rear Nearside Hose Locker
Roller Shutter Serial No.
OS 1 (Front offside locker)
Roller Shutter Serial No.
OS 2 (Wheel arch offside locker)
Roller Shutter Serial No.
OS 3 (Rear offside locker)
Roller Shutter Serial No.
Rear off side hose locker
Roller Shutter Serial No.
All roller shutters fitted with “Lime-Green” pull-down straps
3.3 Check door fit, compression latch operation, door seal of hinged doors
Front Nearside Upper Locker
Front Nearside Lower Locker
NS 4 (Lower rear nearside locker)
Front Offside Suction Hose Locker (Upper Locker)
Front Offside Lower Locker
OS 4 (Lower rear offside locker)
3.4 General finish of the bodywork.

Lockers

3.5 Guttering attachment :- Above all lockers
3.6 Roller Shutters fitted with weatherproof brush seal. Brush seal to contact roller shutters
3.8 Electrical Wiring
Nearside Lockers
Offside Lockers
Rear Lockers
3.9 Rubber Floor Matting
Front NS Upper Locker : Rubber floor for BA Staging Matt
Locker NS 1 : Top & middle shelves and floor
Ladder compartment fitted with full width & length nylon strip
No rubber matting on B.A. shelf
Locker NS 2 : Lower slide & tilt tray
Locker NS 3 : No rubber floor matting under dead hose reel
Locker NS 4 : No rubber floor matting
Rear NS Locker : No rubber floor matting
Front OS Suction Hose Locker : No rubber floor matting
Locker OS 1 : Top, middle & lower shelves
Rubber matting on slide-out trays for hydraulic equipment & PPV fan (Note : Nitrile rubber for hydraulic equipment tray)
Rubber Chequer Plating Floor Matting on large slide-out tray
Locker OS 2 : One (1) slide & tilt trays
Top wet hose stowage fixed shelf
Locker OS 3 : No rubber floor matting under dead hose reel
Locker OS 4 : No rubber floor matting
Rear OS Locker : No rubber floor matting
3.10 Stainless steel trim over bottom sill of all locker openings
3.11 No sharp edges & Dome head nuts to be used on contract points in lockers
3.12 General cleanliness

Locker Contents

3.13 Front NS Locker
Upper Area of Locker :- Stowage bracket for Staging Mat (Aluminium base & 2 Velcro straps)
Four (4) Aluminium Tubing for Class “B” pick-up tube & stick and two (2) ceiling hook
Lower Area of Locker :- Slide-out tray for the stowage of witches hats, E-flare carry bag & two (2) of traffic tape
Nylon guides located on side wall of locker
NS1 (Front Nearside Locker)
Top left-hand side fixed shelf (above the ladder compartment)
Top middle fixed shelf
Top right-hand side fixed shelf (for splash suits & rubber boots) (above Pantograph B.A. brackets)
Vertical partition fitted at the back of top right-hand side shelf to ensure access to equipment
Full height ladder compartment on the left-hand side) (Nylon floor)
Roof mounted stowage bracket with “Lime-Green” Velcro strap for Stage 2 B.A. Control Board (B.A. Shelf Shelf)
“Little Giant” Combination Ladder Type 1A Model No. M17-10102 (fitted with Velcro retaining strap)
Middle fixed shelves in the centre area of the locker complete with a set of three (3) lockable drawers (right-hand side of ladder compartment)
First Aid Kit Area to be colour coded “Green”
“Approved” B.A. Pantograph Bracket with “Lime-Green” Velcro straps & plastic coated spring clips
Fixed B.A. shelf to contain circular bracket for B.A. Guide Line in back left-hand corner
Fixed B.A. shelf to have bracket for spare Oxy-Viva cylinder on the right-hand side
Fixed B.A. shelf to be reinforced to minimum shelf flexing
Fixed shelf complete with two (2) partitions under B.A. shelf.
Lower shelf (floor area) for two (2) CFA supplied Gas Suits Cases
Right-hand side of locker to be fitted with brackets & Velcro strap for combined Axe & Hooligan Tool
3.15 NS 2 (Wheel Arch Nearside Locker)
Full width lower slide & tilt tray arrangement
Tray to be retained in the fully closed positions
Middle, right-hand side area c/w “Hose on the Bight” Rack with five (5) adjustable partitions
Drain holes in “Hose on the Bight” rack
Middle, left-hand side area c/w vertical partition and fixed shelf
3/4 top shelf on the left-hand side, above the “Y” collector equipment
Top fixed shelf shall be labelled “PPC SHELF – NO STOWAGE”
Side and rear walls of this area shall be colour coded “Blue” to denote PPC SHELF.
3.16 NS3 (Rear Nearside Locker)
Floor area fitted with fully width slide-out tray
Slide-out tray fitted with Electric Rewind Dead Hose Reel c/w a swivel base
Tray to be retained in the fully closed, 100mm out position & fully opened positions
Small flaked hose tray located on the side of the dead hose reel
Flaked hose tray to retain 15 metres of 38mm hose c/w with one (1) Velcro strap with “D” ring
3.17 NS4 (Rear Lower Nearside Locker)
Stowage for rubber wheel chock and hose ramp
Minimum clear opening width of 380mm
3.18 Rear Nearside Hose Locker
Lower aluminium slide-out hose bin (Hose bin not removable)
Hose bin to the locked in the fully stowed, 100mm out position & fully out positions
Front internal sides to be fully enclosed to stop hose couplings from hooking up in this area
Top front edge of the bin to be lowered to eliminate any pinch points
Top of the hose bin to be fitted with aluminium tray bracket for one (1) 65mm Storz Service Hydrant
Middle area of locker shall have stowage for :- Hose Bandages (Hook) 65mm Branch (Rubber covered) One (1) Portable Radio Holder
Top area of locker shall be recessed back for stowage of hose spanners and adaptors
Area colour coded “Light Blue” for CFA Delivery Adaptors
Area colour coded “Green” for Suction Adaptors
Stowage hooks located at the top of locker for stowage of two (2) One Key Hose Spanners
3.19 Front OS Suction Hose Locker
Upper Area of Locker :- Four (4) PVC Tubing for 125mm Suction Hoses (insertion rubber on inside of locker door)
3.20 OS1 (Front Offside Locker)
Lower (left-hand side) slide-out tray for hose winder trolley
Tray to be locked in the closed and fully out positions
Hose winder trolley easy to remove from tray
Three (3) Dispensers located at top of tray with removable drip tray
Instant FOAM dispenser (outside), Sun Protection (middle) & Hand Wash (inside)
Lower (middle) slide-out tray for PPV Fan c/w Velcro strap
Tray to be locked in the closed and fully out positions
Two (2) lower (right-hand side) fixed shelves for tool bags, socket sets, screwdriver sets, etc.
Middle fixed shelves with vertical partitions for remote lighting equipment, “Sokeral” drum, etc.
Large middle slide-out tray (right-hand side) (slide-out straight)
Large tray to be locked in the :- Closed position & Fully out position
Top fixed shelf (left-hand side) (above hose winder trolley) for drill, saw kit, etc.
Large top slide & tilt tray (right-hand side) for light tripod, spade, rake hoe, etc.
Tray to be locked in the closed position
3.21 OS 2 (Wheel Arch Offside Locker)
Lower slide & tilt tray arrangement (right-hand side) for ground monitor, “Y” collectors, adaptor, etc.
Tray to be locked in the closed positions
Lower slide-out tray arrangement (left-hand side) for dry chemical and foam extinguishers
Tilt stowage brackets fitted for better access to fire extinguishers
Tray to be locked in the closed and fully out positions
Fixed middle shelf (Right-hand side) for stowage of wet hose. Wet Hose Area to be full sealed
Two (2) rear drain holes shall be fitted c/w rubber extension tubes to direct the water away from lower tray
Front edge of the shelf shall be labelled “TRANSPORT – NO STOWAGE
Side and back walls of the wet hose area shall be colour coded “Yellow”
Top fixed shelf for Kore Kooler Chairs, etc.
3.22 OS3 (Rear Nearside Locker)
Floor area fitted with fully width slide-out tray
Slide-out tray fitted with Electric Rewind Dead Hose Reel c/w a swivel base
Tray to be retained in the fully closed position, 100mm out position and fully opened position
Small flaked hose tray located on the side of the dead hose reel
Flaked hose tray to retain 15 metres of 38mm hose c/w with one (1) Velcro strap with “D” ring
3.23
OS4 (Rear Lower Offside Locker)
Stowage for rubber wheel chock and hose ramp
Minimum clear opening width of 380mm
3.24 Rear Offside Hose Locker
Lower aluminium slide-out hose bin (Hose bin not removable)
Hose bin to the locked in the fully stowed, 100mm out position & fully out positions
Front internal sides to be fully enclosed to stop hose couplings from hooking up in this area
Top front edge of the bin to be lowered to eliminate any pinch points
Top of the hose bin to be fitted with aluminium tray bracket for one (1) 65mm Storz Service Hydrant
Middle area of locker shall have stowage for :- Hose Bandages (Hook) 65mm Branch (Rubber covered) Additional Hook for Spare Washers
Top area of locker shall be recessed back for stowage of adaptors
Area colour coded “Light Blue” for CFA 3 TPI Delivery Adaptors
No coloured area for CFA 5 TPI Delivery Adaptors
Area colour coded “Green” for Suction Adaptors
3.25 Rear Locker (Over Pump Instrument Panel)
Locker doors c/w stainless steel side hinges
Door catches located at the bottom of the door
Lockers to be fully sealed with a rubber balloon type door seal
Inside of the doors fitted with white board material
Inside locker (left-hand side) rear cut-out for Fuse Puller Kit
Rear locker fully painted Red
3.26 Rear Wheel Arch Torpedo Tube Lockers
Two (2) B.A. cylinder torpedo tubes in rear wheel arch (both sides)
Hinged locker doors fitted c/w with side door catch
Lockers to be fully sealed with insertion rubber inside locker door
The lower section inside torpedo tubes shall be lined with rubber sheeting to protect the cylinders
Each tube shall be fitted with an elastic strap to ensure a cylinder can be properly secured

Ladder Gantry

3.27 “Centurion” Fire & Rescue Equipment “Rapid-Stow Max” ladder gantry arrangement Ladder release/restraining mechanism shall be incorporated with the ladder gantry
3.28 9 metre “Centurion” Fire & Rescue Equipment double extension aluminium ladder fitted “Arion” Model No. ARIONTX-RO (Stowed Length : 4.122 metres)
Ladder fitted with “Yellow” side handles at the bottom
“Red” reflective tape shall be fitted top to bottom on rear of fly
“Lime-Green” reflective tape from top to bottom on front of fly
3.29 Operation of the ladder release/restraining mechanism
3.30 Operation of the ladder gantry. “Yellow” ladder release handle. Handle marked “LADDER RELEASE”
3.31 Ladder stop bracket at the front of the gantry

Suction Hose Arrangement

3.33 Vehicle fitted with four (4) 125mm Heliflex suction hose c/w 125mm Storz couplings with no handles
3.34 Three (3) 2.2 metre suction hoses shall be fitted
3.35 One (1) 1.8 metre suction hose c/w suction strainer. Total length of suction hose & strainer 2.2 metres
3.36 Suction Hose hold prime
3.37 Suction hose bandit clamps clear of any pinch and sharp points

Body Fill-In Panels

3.38 Body fill-in panels shall be fitted on the front of the body (both sides)
3.39 The fill-in panels shall be suitably braced to stop any vibration
3.40 A front return shall be fitted to each body fill-in panel

Rear Bumper & Support Bracket

3.41 Bumper support bracket located at rear of bodywork
3.42 Two (2) rear bumpers shall be fitted & fully painted white
3.43 LED rear tail lights shall be fitted with the rear bumpers
3.44 No stowage lockers shall be fitted in the top of the rear bumpers
3.45 Located under the fire pump inlets shall be a steel protection frame
3.46 Left Hand Side Rear Bumper fitted with Boat Hook for Hard Suction Hose Tie off Point

Hose Reels

3.50 Electric Rewind Dead Hose Reel located in NS 3 & OS 3
3.51 Dead Hose Reel fitted on slide-out tray and swivel base
Slide-out tray c/w “Yellow” “PUSH” release lever
Swivel base c/w latching system to allow base to be locked into position
3.52 Each reel c/w 90 metres of 38mm extruded rubber hose & 38mm ULC external lug couplings
Small flaked hose tray located at the side of the reel for 15 metres of the 38mm hose with Velcro strap
3.53 Hose reel clutch arrangement with Tee handle located within bodywork fill-in panel (Approx.1,650mm above ground) Tee handle labelled “HOSE REEL RELEASE”
3.54 Hose reel guide rollers fitted at the top, sides & bottom of the reel. Guide rollers properly adjusted to limit drag
3.55 Remote foot switch controls c/w flexible cord
3.56 Manual rewind operation when standing on the ground, Manual rewind handle located in Locker OS 1
3.57 Hose reel friction brake to be accessible when standing on the ground. Brake handle labelled “HOSE REEL BRAKE”
3.58 Pull hose out and check operation of the live reel.
3.59 Suitable guard over any mechanism
3.60 Electric rewind dead hose reels raw stainless steel finish

Body Electrical

Ensure engine running, park brake applied & park lights are on.
3.61 Three (3) LED “Scene” Lights on the nearside & offside of bodywork
3.62 Two (2) LED “Scene” Lights on rear of bodywork
3.63 Delivery outlet LED lights (both sides)
3.64 Two (2) LED number plate lights on rear pump panel
3.65 LED red/amber side markers (both sides)
3.66 Three (3) amber reflex reflectors (both sides)
3.67 24 volt pneumatic operated telescopic light mast on offside of bodywork. Pressure switch on light mast to turn lights on
3.68 LED white light to illuminate the light mast (Parkers “ON” & Park brake applied )
3.69 Locker OS 1 : Large slide-out tray : Fit “Narva” Red courtesy light on front edge of partition
3.70 Pump panel light (Parkers “ON”, Park brake applied and Pump Engaged)
3.71 LED white lights to illuminate the rear top ladder area (Parkers “ON”)

Decals and Reflective Striping

3.72 Diesel Fuel (Offside of Bodywork)
3.73 Tyre Inflation Pressure (rear wheels). (725 kPa)
3.74 “Do Not Overtake Turning Vehicle” (On rear roller shutter, both sides)
3.75 Standard CFA logo (on rear roller shutter, both sides)
3.76 CFA Standard “Emergency 000” Decal located on rear quarter panel of the bodywork
3.77 “Warning Look Up and Live” Decal & “Overhead Powerlines on Poles” Decal (offside) on the rear of the bodywork
3.78 EWPA “Overhead Powerlines on Poles” Decal (nearside) on the rear of the bodywork
3.79 “First Aid” Decal fitted on front nearside roller shutter
3.80 Top of the rear bumper shall be fitted with a “NO STEP” decal
3.81 “Water Signals” Decal on the rear of the bodywork
3.82 “Warning Look Up and Live” Decal located on the pump instrument panel (Red Lettering)
3.83 CFA Red/Yellow reflective striping above roller shutters (both sides)
3.84 “Lime-Green” reflective striping
 Around the side bodywork perimeter (both sides)
 Around the rear bodywork perimeter
 On the roller shutter handles (40mm wide striping)
 On the side fill-in panels
 On all slide-out stowage trays, panels and drawers :-  Locker NS 1  Locker NS 2  Locker NS 3  Rear NS Hose Locker  Locker OS 1  Locker OS 2  Locker OS 3  Rear OS Hose Locker
3.85 Rear bodywork fitted with “night” reflective Class 2 Red/Yellow diagonal striping material

Miscellaneous Equipment

3.88 Rear Swing-Out Stowage Lockers (both sides)
Hinge arrangement for swing-out lockers (180 degrees)
“Yellow” Stay to hold lockers in the open position
Locking mechanism for rear lockers
Rear Lockers to be fully supported in the closed position
3.89 Front NS 1 & OS 1 Lockers fitted with roof mounted external rotating air vent
3.90 Rear NS & OS Hose Lockers fitted with roof mounted external rotating air vent
3.91 Louver type vents located in lower part of the lockers
3.92 Rear wheel arches fitted with CFA logo mudflaps (white/red)
3.93 Fully sealed rubber flexible flare fitted to rear wheel arches
3.94 Rear wheel arch areas & bottom of body finished in “black” body paint
3.95 Rear wheel arch areas lined with “black” brush sheeting material
3.96 Trays, drawers & bins fitted with drainage holes
3.97 All lockers fitted with drainage holes
3.98 All locker shelving fitted with a Reversing 20mm return lip (including black pin weld)
3.99 Retaining velcro stowage straps c/w “D” rings
3.100 All latches & handles colour coded “Yellow”.
3.101 Single bank portable radio holder stowage bracket located in Rear NS Hose Locker

Rear Pump Panel

Rear pump instrument panel checks

4.1 Water Tank Level indicators :-
Full (Blue LED) ; ¾ and ½ (Blue LED) ; ¼ (Orange LED) & Empty (Red LED)
On rear pump panel
On nearside of body (between NS 2 and NS 3)
On offside of body (between OS 2 and OS 3)
4.2 “Cameleon” Class “A” & “B” Foam System Screen.
Power switch
“Real Time Water Flow” Display
Class “A” Concentrate in Percentage (%) Display (0.1%, 0.2%, 0.4% & 0.5%)
Class “B” Concentrate in Percentage (%) Display (3% or 6%)
“Foam Injection Pressure” Display (in bar)
Class “A” Foam Tank Level (in litres remaining)
Class “B” Foam Tank Level (in litres remaining)
Water Tank Level (in litres remaining)
“Maintenance Screen” Function
“User Manual Screen” Function
4.3 Large Screen Display (UV700 Class 1 Display Module).
On Main Screen c/w
Low Pressure Gauge 2500kPa
Compound Gauge -100kPa to 1600kPa
Four (4) x Flowmeters digital display
“OK TO PUMP” Green Indicator light
“PUMP ENGAGED” Red Indicator light
24 hour digital clock with four (4) digit illuminated display numerals
4.4 Large Screen Display (UV700 Class 1 Display Module). On Secondary Screen
Nearside Bodywork Flood Light Switch (Labelled “NEARSIDE”)
Offside Bodywork Flood Light Switch (Labelled “OFFSIDE”)
Pump Bay Area Flood Light Switch (Labelled “PUMP BAY”)
Mast raised/locker open/water level test functions
ON/OFF switch for Class “A” & “B” Foam System
4.5 “EMERGENCY HORN” toggle switch with protection cover
4.6 Reversing Camera
4.7 Remote rear waterproof radio speaker
4.8 Rear radio speaker volume control dial
4.9 Pump governor display and dial control knob
4.10 Light mast control lever c/w locking clamp arrangement
4.11 Light mast raised RED warning light
4.12 Manual lever for first aid tank (Labelled “FIRST AID)
4.13 Four (4) manual levers for delivery outlets
Labelled “CLOSED” & “OPEN”
Numbered 1 ; 2 ; 3 ; 4
4.14 Low pressure pump symbol (LP) with green “OK TO PUMP” light
4.15 Manual lever for recirculation tank fill (Labelled “RE-CIRC/TANK FILL VALVE”)
4.16 Class “A” & “B” Foam Storz Coupling for “EXTERNAL FOAM SUPPLY & TANK FILL”
4.17 Class “A” & “B” Foam Control Valve Handle
4.18 Vehicle to squat when pump is engaged
4.19 65mm Storz Inlet blank caps shall be colour coded “Green”
65mm Storz Inlet blank caps fitted with retaining chains/cables
65mm Storz couplings shall be to “NEN 3374” standard
65mm Storz lugs in 12 & 6 o’clock positions
4.20 65mm Storz Inlets fitted with stainless steel mesh inline strainers
4.21 Bleed line shut-off valves fitted to 65mm Storz inlets. Shut-off bleed valves shall be fully accessible and c/w “Red” handles
4.22 Lever type hard suction butterfly valve shall be fitted. Lever handle shall be colour coded “Green”
4.23 125mm inlet fitted with 125mm blank cap (no handles) with retaining chain (Green Coupling)
4.24 Bleed line shut-off valves fitted to 125mm Storz hard suction. Shut-off bleed valve shall be fully accessible and c/w “Red” handle
4.25 125mm hard suction tubing fitted with vortex plate
4.26 No inline strainer fitted in 125mm hard suction inlet
4.27 Pressure Relief Hole in 65mm Storz Delivery Blank Caps. Small hole to reduce pressure that may build up behind from delivery manifold.
4.28 Fixed rod type stay fitted on back of pump instrument panel frame. Rod stay to be colour coded “Yellow”
Open pump bay and check components

Pump test

2. Fire Fighting Pump and Plumbing (Pump to be started at beginning of inspection – min. running 3 hrs)

5.1 Check all 65mm Storz deliveries for flow
5.2 Check the pump manual speed control operation
5.3 Check the pump governor operation
5.4 Closed pump Pressure (Kpa)
5.6 Typical recorded pump pressure and flow rates. Specified performance; 4000 Lpm @ 1000Kpa. Please used spread sheet for full pump test notes.
Undertake from hard suction.
400 Kpa Delivery/Compound Pressures
500 Kpa Delivery/Compound Pressures
600 Kpa Delivery/Compound Pressures
700pa Delivery/Compound Pressures
800 Kpa Delivery/Compound Pressures
900 Kpa Delivery/Compound Pressures
1000 Kpa Delivery/Compound Pressures
5.7 Check both dead hose reels operation.
5.8 Check recirculation / tank fill operation.
5.9 Supply water from first aid tank
5.10 Fill tank to ¾ full using the hard suction and recirculation line.
5.11 Separate Class “B” foam line fitted c/w ball valve & located on offside delivery outlets
25mm Storz coupling colour coded “Yellow”
Class “B” foam line labelled “CLASS B FOAM OUTLET”
Ball valve fitted with “Yellow” handle
5.12 Check the Class “A” & “B” Foam transfer pump operation
5.13 & 5.14 Check the operation of the “Cameleon” Class “B” Direct Injection Foam Proportioning System (Operated from Pick Up Stick and Foam Tank)
At 3% setting from Pick Up Stick
At 3% setting from Foam Tank
At 6% setting from Pick Up Stick
At 6% setting from Foam Tank
5.15 Class B Foam Tank Breather : Tank to be fitted with an open vent tube arrangement to allow foam to be filled and drawn from tank.
5.16 & 5.17 Check the operation of the “Cameleon” Class “A” Direct Injection Foam Proportioning System (Operated from Pick Up Stick and Foam Tank)
At 0.1% setting from Pick-Up Stick
At 0.1% setting from Foam Tank
At 0.2% setting from Pick-Up Stick
At 0.2% setting from Foam Tank
At 0.4% setting from Pick-Up Stick
At 0.4% setting from Foam Tank
At 0.5% setting from Pick-Up Stick
At 0.5% setting from Foam Tank
5.18 Class “A” Foam Tank Breather : Tank to be fitted with an open vent tube arrangement to allow foam to be filled and drawn from tank.
5.19 Completely fill the first aid tank using a hydrant and the appliance 65mm Storz fill line.
5.20 65mm Storz tank fill line located at front of bodywork (nearside)
5.21 65mm Storz coupling to be colour coded “Green” c/w cable tie on blank cap
5.22 65mm Storz coupling fitted with stainless steel mesh inline strainers
5.23 Pump to be operated continuously from 30 minutes at 1,000 kPa (Delivery Pressure). One (1) delivery line to be used.
Check no excessive vibration at 1st centre bearing bracket.
5.24 Check operation of low water level
¼ tank level (amber light in cabin & rear amber strobe illuminates) (siren sounds for 5 seconds)
Rear amber strobe continues to illuminate until tank filled to ¾ .
5.25 Water tank to pump supply line fitted with non-return check valve. (Cannot fill water tank through tank to pump line)
5.26 Class 1 pump governor controller should read kPa when pressure mode is selected. (Not in PSI)
Other:
Other:
Other item
Other item

Road Test

Driving Test (nom. 20-30 km – on road and off road)

6.1 Steering Wheel in correct alignment.
6.2 All instruments working.
6.3 Park Brake operation.
6.4 Service Brake operation.
6.5 Exhaust Brake operation.
6.6 Engine Retarder operation (automatic transmission only).
6.7 No vibrations evident.
6.8 No noises / rattles.
6.9 Holding brake air pressures.
6.10 Normal Battery Charge rate.
6.11 Normal Engine Temperature.
6.12 Normal Oil Pressure.
6.13 Check top road speed. Maximum 110 km/hour
6.14 Speed Limited.
6.15 Check acceleration times.
Maximum times:
0-35 km./hour in 8 seconds
0-50 km./hour in 15 seconds
0-65 km./hour in 24 seconds
6.16 Check Cruise Controls (on steering wheel)
6.17 Check Buzzer fitted to Squat Mode, when hand brake release & vehicle squatted
6.18 Vehicle Fuel Tank full.
Ensure no Cab/Chassis fault codes or other OEM faults present
Other Items

Stowage

Stowage equipment;

Front NS Locker :-

7.1 One (1) BA Staging Area Mat (with Bag)
7.2 One (1) 25mm Storz Class “B” Foam Stainless Steel Pick-up Stick and Line
7.3 One (1) 25mm Storz Class “B” Foam Pick-up Line
7.4 Two (2) Ceiling Hooks and Handles
7.5 Six (6) Witches Hats (450mm Reflective Fluro Orange)
7.6 Two (2) Traffic Tape (CFA/DSE red/white 100mm x 75mm)
7.7 One (1) E-Flares MP 730 Kit

Locker NS 1

7.8 One (1) Ladder Gantry Handle
7.9 One (1) “Little Giant” Combination Ladder
7.10 One (1) Soft Pack First Aid Kit
7.11 Ten (10) Safety Spectacles in Pouch (Clear Container)
7.12 One (1) Pack of Nitrile Glove with Dispenser
7.13 Hooligan Tool with strap (kit)
7.14 Fire Fighters Axe with strap (kit)
7.15 Two (2) “White” Patient Blankets
7.16 Container with Ration Packs
7.17 One (1) 3 Drawer Storage Unit
7.18 One (1) 50/pack Electrolyte Powder Sticks
7.19 One (1) Pack of Soft Ear Plugs
7.20 Ten (10) Bio Hazard Bags
7.21 One (1) Pack of 20 Draeger Face Mask with Bag
7.22 Insulated Cooler Bag (CFA Logo)
7.23 “PLUG IT UP” 500 gram Container
7.24 Three (3) 7 litre Clear Stowage Containers

Locker NS 2 :-

7.25 One (1) “Quicklay” Hose Lay Pack Bag (Blue) Complete with;
One (1) 30 metre x 38mm, Class H, extruded hose c/w ELC couplings
One (1) 65mm Storz – 38mm ELC Dividing Breeching Piece
One (1) 65mm Storz – 64mm 3TPI Female Adaptor
One (1) Red Ant One Key Hose Spanner
7.26 One (1) “Quicklay” Attack Pack Bag (Red) Complete with;
One (1) 30 metre x 38mm, Class H, extruded hose c/w ELC couplings
One (1) TFT G-Force Nozzle (450 LPM @ 3bar)
One (1) Red Ant One Key Hose Spanner
7.27 Two (2) 65mm Storz Breeching Piece (Y Collector)
7.28 Two (2) 65mm Storz Canvas Delivery Hose x 30 metre long
7.29 Two (2) 65mm Storz Duralite Delivery Hose x 15 metre long
7.30 One (1) 38mm External Lug Extruded Rubber Delivery Hose x 30 metre long

Locker NS 3

7.31 Three (3) 30 metre lengths of 38mm Delivery Hose with External Lug Couplings (On the Electric Dead Hose Reel)

Lockers NS 4

7.32 One (1) 65mm Rubber Hose Ramp
7.33 One (1) Wheel Chock (with reflective striping )
7.34 One (1) 125mm Wire Strainer Basket

Rear NS Hose Locker

7.35 Five (5) 65mm Hose x 30 metre long c/w 65mm Storz Coupling Hose fitted with Delivery Washers
7.36 One (1) 65mm Service Hydrant with 65mm Storz Couplings. One (1) One Key Hose & Hydrant Spanner with Cover
7.37 One (1) 65mm (5 bar) TFT Fulltime Swivel Branch
7.38 Two (2) 65mm Storz to 64mm CFA 3 T.P.I. Male Adaptor (Blue)
7.39 One (1) 65mm Storz to 38mm External Lug Adaptor (Blue)
7.40 One (1) 65mm Storz Blank Cap (Blue) (with small bleed hole)
7.41 Two (2) 65mm Storz to 64mm CFA 3 T.P.I. Female Loose Nut (Green)
7.42 One (1) 90mm to 65mm Storz Adaptor (Aluminium Raw)
7.43 Two (2) 65mm Hose Bandages
7.44 Two (2) 38mm Hose Bandages
7.45 Two (2) One Key Hose & Hydrant Spanner

Rear Locker (Above Pump Panel) :-

7.46 Fuse Puller Kit c/w
One (1) Telescopic stick (fuse puller) (red bag)
One (1) pair of Electrical Insulating Gloves
One (1) Accessories (hook, universal hastings)
One (1) pair of Outer Leather Gloves
7.47 One (1) 10 litre Collapsible Bucket
7.48 One (1) Equipment Lifting Bag
7.49 One (1) 5 litre Clear Stowage Container

Front OS Suction Hose Locker

7.50 Three (3) 125mm Diameter Heliflex Suction Hose x 2,200mm long
7.51 One (1) 125mm Diameter Heliflex Suction Hose x 1,800mm long with Suction Strainer (Overall Length : 2,200mm long)

Locker OS 1

7.52 One (1) Hose Rolling Trolley
7.53 Triple Dispenser – Sunscreen/Hand Wash/Sanitiser
7.54 One (1) Positive Pressure Ventilation (PPV) Fan with Emission Control
7.55 Two (2) “Pelican” Remote Area Lighting Packs
7.56 20 litre Canoe Drum (Sokeral Absorbent
7.57 One (1) 610mm Bolt Cutters
7.58 One (1) Wooden Handle Rakehoe (McLeod Tool)
7.59 One (1) “Pelican” Tripod
7.60 One (1) “Farmers Friend” Wooden Handle Shovel
7.61 One (1) Broom/Squeegee Head
7.62 One (1) 1.4m Single Nupla Grip Handle Ferrule
7.63 One (1) 125mm to 2 x 65mm Storz Breeching Piece
7.64 One (1) 90mm to 64mm CFA 3 T.P.I. Female Loose Nut
7.65 One (1) 125mm to 90mm Storz Adaptor
7.66 One (1) 5 litre Two Stroke Fuel Container (Metal) (Grey)
7.67 One (1) 5 litre Unleaded Fuel Container (Metal) (Red)
7.68 One (1) Metal Fuel Funnel (Red)
7.69 One (1) Fuel ID Unleaded Plastic Tag (Red)
7.70 One (1) Fuel ID Two Stroke Plastic Tag (Grey)
7.71 One (1) Pair of PVC dipped Chemical Gloves
7.72 One (1) Pair of Electrical Gloves
7.73 One (1) “Weber” Handvario Combi Tool
7.74 One (1) “Weber” ABS Plastic Wedge (3”W x 8.5”L)
7.75 One (1) Multi-Purpose Hand Saw
7.76 One (1) Chimney Mirror
7.77 “Husqvarna” K970 Quick Cut Rescue Saw
7.78 Two (2) Heavy Duty Tarpaulins
7.79 One (1) Milwaukee Reciprocating Saw with Rechargeable Batteries
7.80 One (1) Pack of 5 “Lenox” Reciprocating Blades
7.81 One (1) Milwaukee Impact Cordless Drill with Rechargeable Batteries
7.82 One (1) Multi Voltage Charging Unit
7.83 One (1) Milwaukee Impact Bit Driver Set (29 piece)
7.84 One (1) Socket Set (43 Piece)
7.85 Three (3) Bi-Carb Soda 350g “Shake & Pour” PET Plastic jar
7.86 One (1) Keyless Drill Chuck (0.6-4mm)
7.87 One (1) Drill Bit (10 pack)
7.88 One (1) 10 kg Tool Tether 1800mm
7.89 One (1) 500gm Container “PLUG IT UP”
7.90 Warning Triangle Set
7.91 Two (2) 20 litre Clear Stowage Container
7.92 One (1) Soft Bag Tool Kit containing.
Three (3) Flat Blade Screwdrivers
Three (3) Phillips Head Screwdrivers
One (1) 150mm Shifting Spanner
One (1) 250mm Shifting Spanner
One (1) Engineers Chisel
One (1) 1.35kg Club Hammer
One (1) Claw Hammer
One (1) 250mm Pipe Wrench
One (1) 10 piece Metric Allen Key Set
One (1) 10 piece Imperial Allen Key Set
One (1) Torx Driver 8 Piece Set
One (1) 165mm Stanley Folding Jab Saw
One (1) 175mm Pointed Nose Multi Vice Grips
One (1) 250mm Curved Multi Vice Grips
One (1) 4mm Long Series Pin Punch
Two (2) 19mm x 12m Yellow Thread Sealing Tape
One (1) Black/Yellow Safety Stripe / Duct Tape
One (1) 300mm Heavy Duty Hacksaw
Three (3) 18 Teeth Hacksaw Blades
Three (3) 24 Teeth Hacksaw Blades
Three (3) 32 Teeth Hacksaw Blades
One (1) Pack of 100 Cable Ties (188mm, Flouro Pink)
7.93 One (1) Soft Bag MVA Kit containing;
One (1) 25mm Nylon Hammer
One (1) Phillips Head Screw drivers 6 piece kit (coated red)
One (1) Flat Blade Screw drivers 6 piece kit (coated red)
One (1) 200mm Shifting Spanner (plastic coated red)
One (1) 150mm Shifting Spanner (plastic coated red)
One (1) 13mm OE Spanner (plastic coated red)
One (1) 10mm OE Spanner (plastic coated red)
One (1) 230mm Cable Shears (plastic coated red)
One (1) Curved Nose Pliers (plastic coated red)
One (1) Needle Nosed Pliers (plastic coated red)
One (1) Side Cutting Pliers (plastic coated red)
One (1) Pointed Nose Vice Grips (plastic coated red)
One (1) Multigrips (plastic coated red)
One (1) Spanner Set roll (24 slots for insulated tools) (red)
One (1) Vehicle glass breaker hammer & seatbelt cutter
One (1) Pack of 100 Cable Ties (188mm, Yellow Pink)
Two (2) PVC Electrical Tape (3M Temflex 1610, rainbow colour)
One (1) Tape – Non Deployed Airbag, Adhesive (66M) (CFA/SES

Locker OS 2

7.94 One (1) 65mm 5 bar 2000 LPM Ground Monitor
One (1) 5 bar Stacked Tips
One (1) Monitor Tie Down Bag
One (1) 5 bar 2000 LPM Combo Tip
7.95 One (1) 9 litre “B” Class Foam Extinguisher (3A 30B)
7.96 Two (2) 4.5 kg ABE Dry Chemical Extinguishers (4A : 60BE)
7.97 One (1) 450 LPM “Angus” Foam Branch with 65mm Storz Coupling
7.98 One (1) 450 LPM “Angus” Foam Inductor with 65mm Storz Coupling
7.99 Foam Aspirator Attachment (TFT Low)
7.100 Two (2) Kore Kooler Chairs and Bags
7.101 Two (2) 58mm Cap & Bung Spanners (for Foam Drums)

Locker OS 3

7.102 Three (3) 30 metre lengths of 38mm Delivery Hose with External Lug Couplings (On the Electric Dead Hose Reel)

Locker OS 4

7.103 One (1) 65mm Rubber Hose Ramp
7.104 One (1) Wheel Chock (with reflective striping )

Rear OS Hose Locker

7.105 Five (5) 65mm Hose x 30 metre long c/w 65mm Storz Coupling Hose fitted with Delivery Washers
7.106 One (1) 65mm Service Hydrant with 65mm Storz Couplings One (1) One Key Hose & Hydrant Spanner in Cover
7.107 One (1) 65mm (5 bar) TFT Fulltime Swivel Branch
7.108 Three (3) 38mm Hose Washers
7.109 Three (3) 65mm Hose Washers
7.110 Two (2) 65mm Hose Bandages
7.111 Two (2) 38mm Hose Bandages
7.112 Two (2) 65mm Storz to 64mm CFA 5 T.P.I. Female Loose Nut full time swivel Adaptor
7.113 Two (2) 65mm Storz to 64mm CFA 5 T.P.I. Male Adaptor
7.114 Two (2) 65mm Storz to 64mm CFA 3 T.P.I. Male Adaptor (Blue)
7.115 One (1) 65mm Storz to 64mm CFA 3 T.P.I. Female Loose Nut full time swivel Adaptor (Green)
7.116 One (1) 65mm Storz to 38mm External Lug Coupling Adaptor (Blue)

Crew Cabin

7.117 Five (5) Crew Protection Blankets (1.8m x 2.0m Red CFA)
7.118 One (1) “Pelican” 9410 Large Rechargeable LED Torch
7.119 Four (4) “Pelican 3715 LED Battery Torches
7.120 One (1) Sanuders Criusermate Metal Folder
7.121 One (1) Pack of Nitrile Glove with Dispenser
Other stowage items noted;

Other

Other items noted during inspection
Other items noted during inspection
Vehicle requires reinspection
Check and record pump hours and K's
Signature

CFA Medium Pumper Quality Assurance Inspection

Free CFA Medium Pumper Quality Assurance Inspection Checklist

Go digital today!

Convert your paper checklists into digital forms

Quality Insurance Inspection Medium Pumper Inspection

1. Commencement of pumping;

2. Cab/Chassis

Decals inside the cabin

Cabin Tilt Arrangement: WARNING: If the fire pump is running beware of rotating drive shafts.

Decals on the cabin exterior

Miscellaneous Equipment

Body General :-

Locker doors

Lockers

Locker Contents

Ladder Gantry

Suction Hose Arrangement

Body Fill-In Panels

Rear Bumper & Support Bracket

Hose Reels

Body Electrical

Decals and Reflective Striping

Miscellaneous Equipment

Rear pump instrument panel checks

2. Fire Fighting Pump and Plumbing (Pump to be started at beginning of inspection – min. running 3 hrs)

Driving Test (nom. 20-30 km – on road and off road)

Stowage equipment;

Front NS Locker :-

Locker NS 1

Locker NS 2 :-

Locker NS 3

Lockers NS 4

Rear NS Hose Locker

Rear Locker (Above Pump Panel) :-

Front OS Suction Hose Locker

Locker OS 1

Locker OS 2

Locker OS 3

Locker OS 4

Rear OS Hose Locker

Crew Cabin

Other

Related checklists