Title Page

  • Site Conducted

  • System Size DC (kWp)

  • System Size AC (kW)

  • Conducted on

  • Prepared by

  • Location
  • Document Number

Solar Site Inspection

General Site Conditions

  • Time of Inspection.

  • Ambient temperature.

Overall site inspection

Fencing and access control

  • Are all fences and gates intact and without ay visible damage where applicable?

  • Are all locks functional and not corroded?

  • Are all walkways and paths clear of debris and vegetation where applicable?

Water supply

  • Are all water supply points accessible and operating correctly?

Lightning protection system

  • Where applicable, does the LPS appear to be intact and functional? Check specifically for corrosion at joints, damage to conductors, etc.

General Cable Routing Inspection

  • Confirm no cable damage in trunking or trays

  • Confirm trunking and trays are still secure

  • Cables are not at risk of damage on bends

  • Cable tray covers are still intact

  • Warning labels are still intact

  • Test trays or trunking for bonding continuity with a low-ohm continuity tester to see if it adheres to less than 0.2 ohm.

  • This section is for anything you may want to take note of during your inspection.

DC Combiners (Where applicable)

  • Check for loose connections and secure where necessary

  • Check for hotspots, scorch marks, damage, deformities, etc.

  • Confirm no physical damage inside and outside box

  • DC box is watertight and dust free

  • Box is still secured to wall mount

  • Fuses are in tact

  • Warning labels are still intact

  • Surge protection is in working condition

  • Glands are properly sealed

  • Earthing is in tact

  • This section is for anything you may want to take note of during your inspection.

General inverter inspection

  • Check for loose connections and secure where necessary (on each inverter)

  • Check for hotspots, scorch marks, damage, deformities, etc.

  • Inverter and inverter fans are dust free

  • Mounting to wall is secure

  • Communication board is in proper working condition

  • Inverter room ventilation is appropriate

  • Inverter switches are in proper working condition

  • Labelling is still in tact

  • Protection devices are intact

  • Test voltage between earth and neutral connections

  • Test voltages with multi-meter (AC, on & off)

  • Test amperage with multi-meter (AC & DC)

  • After a Power Cycle the system is in good working condition

  • Inverter is clear of dust

  • Thermal imaging

  • This section is for anything you may want to take note of during your inspection.

AC Distribution Board

  • Check for loose connections and secure where necessary

  • AC DB is still securely mounted and undamaged

  • AC DB is not overheating

  • All breakers are in working condition

  • Check for hotspots, scorch marks, damage, deformities, etc.

  • Surge protection is in working condition

  • DB has no external damage

  • Labelling is still in tact

  • Test voltages with multi-meter

  • Test amperage with multi-meter

  • Test earth and neutral connections with multi-meter

  • Temperature in the DB is suitable for proper working condition

  • All components are secured properly to DB panels

  • Thermal imaging

Weather station and monitoring system

  • Where a UPS is installed, battery is still correctly charging and discharging? (Check with mains failure test, measure voltage with and without mains)

  • Weather sensors are securely connected and fastened

  • Cables are secure and watertight

  • Protection devices are intact (where applicable)

Energy Meter

  • Meter is still functional

  • Check for loose connections on meter

  • Check for loose connections of breaker

  • Protection devices are intact

  • Wall mount connection is secure

  • Inverter inspection
  • Please provide inverter number and serial number.

  • Are all parameters still configured as originally intended? For example NRS 097-2-1.

  • Is the active cooling system fully functional and free from excessive noise?

  • Are all air vents free from dust and debris?

  • Are all connectors and terminations still mechanically sound?

  • Are the DC isolators fully functional? (Confirm if inverter shuts down when AC power is removed and the DC isolators are opened.)

AC Voltage Measurements at Inverter CB

  • Phase A to B (V)

  • Phase B to C (V)

  • Phase A to C (V)

  • Phase A to Neutral/Earth

  • Phase B to Neutral/Earth

  • Phase C to Neutral/Earth

AC Voltage Measurements at Inverter Terminals

  • Phase A to B (V)

  • Phase B to C (V)

  • Phase A to C (V)

  • Phase A to Neutral/Earth

  • Phase B to Neutral/Earth

  • Phase C to Neutral/Earth

  • Neutral at inverter to earth terminal in DB

  • String Test
  • Seaward IV Curve Test Result

  • Insulation resistance test result on string at 1000V (MegOhm). Positive to earth, negative to earth and positive to negative.

The templates available in our Public Library have been created by our customers and employees to help get you started using SafetyCulture's solutions. The templates are intended to be used as hypothetical examples only and should not be used as a substitute for professional advice. You should seek your own professional advice to determine if the use of a template is permissible in your workplace or jurisdiction. You should independently determine whether the template is suitable for your circumstances.