Information
-
Jobsite Safety Inspection
-
Site
-
Date & Time
Jobsite General
-
Is any form of site specific training/orientation being held?
-
Is the First-Aid kit available and fully stocked?
-
Send out fully stocked First-Aid kit
-
Is an eye wash station available and filled properly?
-
Onsite?
-
Send out Station and Solution
-
Onsite but Not Full?
-
Fill station properly and make accessible
-
Are safety signs posted and readable?
-
Furnish/replace signs to show proper safety precautions
-
Are emergency phone numbers posted?
-
Post numbers where visible to workers
-
Has adequate access to the site been provided?
-
Notify superintendent to make sure that site is accessible in a safe manner for all
-
Is all protruding rebar properly guarded?
-
Cap all exposed rebar ends with OSHA cap
Housekeeping
-
Are walkways and stairs clear and kept free of debris?
-
Clean areas to avoid slips, trips, and falls.
-
Is the temp. lighting adequate and is it in good working condition?
-
Is there enough of it?
-
Add more temp. lighting
-
Are there bulbs in every socket?
-
Put bulbs in every socket
-
Are all bulbs protected?
-
Protect each bulb with properly installed cages
Fire Protection and Prevention
-
Are fire extinguishers on site and serviced properly?
-
Provide fire extinguishers/switch out expired fire extinguishers
-
Are all flammable liquid containers properly identified?
-
Make sure all are clearly marked with "Flammable"
-
Are the acetylene and oxygen bottles stored correctly?
-
Are bottles secured upright?
-
Secure each bottle in upright position
-
Are the bottles capped and separated by at least 20 feet?
-
Cap and separate properly
Personal Protective Equipment (PPE)
-
Are all employees wearing hard hats, safety glasses, and high visibility clothing on the outermost layer?
-
Hard Hat
-
Subs in Violation:
-
Safety Glasses
-
Subs in Violation:
-
High Visibility Clothing
-
Subs in Violation:
-
Are all employees wearing the proper footwear?
-
Send the employee(s) home to get the proper footwear
-
Are respirators being used properly when required?
-
Get the proper respirators on ASAP
-
Is hearing protection being used when required?
-
Get the proper hearing protection on ASAP
Fall Protection
-
Are ladders properly setup and being used correctly? (tied off, 4:1 angle, extend 3' above)
-
Using the right ladder for the job?
-
Get the correct ladder for the job being performed
-
4:1 angle?
-
Correct to required 4:1 angle
-
Step ladder fully opened?
-
Open Fully
-
Extended 3' above?
-
Extend ladders 3' above
-
Is ladder tied off if necessary?
-
Tie off properly
-
Are employees standing on the top 2 steps of the step ladder?
-
Get off the top steps and find a taller ladder for the job
-
Is the ladder damaged or defective?
-
Take out of service immediately
-
Are employees using proper fall protection methods?
-
Are employees wearing the fall protection properly?
-
Are the perimeter cables/guard rails properly installed?
-
Are cables/guard rails installed at all required locations?
-
Install perimeter cables/guard rails properly at all required locations
-
Are cables/guard rails installed at proper height?
-
Make sure all cables/guard rails are between 39 and 45 inches in height
-
Is there both a top and mid rail in place?
-
Make sure all top and mid rails are in place and secure
-
Are toe boards required/installed correctly?
-
Install toe boards correctly
-
Is the scaffolding setup correctly?
-
Height/Width ratio aceptable
-
X-Braces in place
-
Install X-Braces properly
-
Guard rails in place/tied off
-
Install guard rails properly or tie off
-
Pins in place
-
Put all pins in proper locations
-
Fully planked
-
Plank fully with proper planks
-
Wheels/Base Plates in place
-
Install wheels/base plates
-
Height:Width ratio acceptable
-
Tie into building or add outriggers
-
Has the scaffold been inspected daily by a competent person?
-
Inspect daily and use scaffold tags
-
Are floor holes properly covered and protected?
-
Cover, Protect, and Label Exposed Floor Holes
Electrical
-
Are all extension cords in good working condition?
-
Took out of service
-
Is the electricity on site being used through a GFCI or welder?
-
Make sure all cords are run through a GFCI
-
Are the electrical panels labeled, locked, and free of holes?
-
Labeled
-
Label panel correctly
-
Locked
-
Lock panel
-
Free of holes
-
Cover all holes
-
Are all hot outlets and switches properly covered?
-
Put covers on or cut power
Trenching
-
Are the trenches properly protected against cave in?
-
Is there a competent person on site for daily trench protection?
-
Shut down trenching operations until there is one
Tools
-
Are guards in place and used correctly on all tools that require them?
-
Stop using tools immediately and replace all guards
Mobile Equipment
-
Is the mobile equipment on site in good working condition?
-
Repair/Replace Equipment Immediately
-
Are crane barricades properly installed and rigging in good condition?
-
Barricades installed
-
Install crane baricades
-
Rigging in good condition
-
Replace with proper rigging
-
Is the 10' minimum distance from power lines maintained?
-
Adjust equipment accordingly