Title Page
-
GeoOP job number
-
Client / Site
-
Conducted on
-
Prepared by
-
Location
-
PV module manufacturer and model number
- Sapphire gem 270 watt
- Sunpower 327 watt
- Sunpower 345 watt
- CSUN 260 watt
- Trina Honey 260 watt
- Trina Honey 270 watts
- Other
-
Number of solar modules
-
String Configuration
-
Inverter manufacturer and model number
-
Number of inverters
-
Number of MPPTs
-
PV array tilt and orientation
-
Array frame is certified to AS1170.2 for installation location
-
Array frame is installed to to manufacturers instructions
-
No galvanically dissimilar metals are in contact with the array frames or supports
-
Roof penetrations are suitably sealed and weatherproofed
-
PV wiring losses are less than 3% at the maximum current output of the array
-
Where PV array comprises multiple strings, string protection has been provided
-
Wiring is protected from mechanical damage and is appropriately supported
-
Weatherproof PV isolator mounted adjacent to array
-
All low voltage wiring has been installed by a licensed electrical tradesperson
-
All wiring has been tested and approved by a qualified electrical tradesperson
-
PV array isolator mounted adjacent to the inverter
-
Isolator is mounted on output of inverter
-
Lockable AC circuit breaker is mounted within the switchboard to act as the inverter main switch for the PV/inverter
- 16 Amp
- 20 Amp
- 25 Amp
- 32 Amp
-
Inverter is installed to manufacturers specification
-
Inverter ceases supplying power within 2 seconds of a loss of mains power
-
Inverter does not resume supplying power until mains have been present for more than 60 seconds
Continuity check
-
Continuity of all strings, sub-arrays and array cables
-
Continuity of all earth connections (including module frame)
Insulation resistance measurements
-
Array Positive to earth M ohm
-
Array negative to earth M ohm
System check
-
String 1 Voc
-
String 1 inverter operating voltage
-
String 1 short circuit current
-
String 1 operating current
-
String 1 polarity
-
String 2 Voc
-
String 2 inverter operating voltage
-
String 2 short circuit current
-
String 2 operating current
-
String 2 polarity
Anti Islanding Test
-
Time for inverter to disconnect is less than 2 seconds
-
Time for inverter to reconnect greater than 60 seconds
Installers Information
-
CEC installers name
- Cameron Walker
- Christopher van Zanten
- Mark Doolan
- Kyle Schubert
-
CEC installers signature
-
CEC accreditation number
- A9975582
- A1575465
- A9768638
- A3956368
-
CEC designers name
- Cameron Walker
- Christopher van Zanten
- Mark Doolan
- Kyle Schubert
-
CEC designers signature
-
Electricians license number
- E37355 - 209363C
- A45153 - 293549C
- A50178 - 68022S
- A54184 - 75163S
-
Electricians signature
The following safety/warning labels have been attached
-
"Warning" Dual Supply -Isolate both normal and solar supplies before working on this switchboard. (On switchboard that inverter is directly connected)
-
"Normal supply" main switch (is permanently fixed at the main switch)
-
"Solar supply" main switch (is permanently fixed at the solar main switch)
-
"Warning" Dual supply - isolate solar supply at Distribution Board (where the inverter connects to a DB)
-
Inverter location (where the inverter is not located adjacent to the main switchboard)
-
"Warning" hazardous DC voltage (Permanently fixed on array junction boxes)
-
"Solar array on roof" and "PV" labels (permanently fixed on MSB and/or meter box)
-
"PV array DC isolator" (DC isolator a clearly identified)
-
"Warning - multiple DC sources" (Placed adjacent to inverter when multiple isolator are used and not ganged together)
-
"Solar" (Labels placed on exterior of wiring enclosures)
-
"Shut down procedure" (permanently fixed at inverter and/or main switchboard)