Information
-
Work Order Number
-
Start Time
-
Location
-
Customer
-
Service Person
-
Machine
-
Serial Number
Workspace Inspection
-
Inspect work area for Slips, Trips and Fall Hazards
-
Has the Hazard been fixed?
-
Contact your Supervisor for further instruction.
-
Inspect Area for Traffic Hazards
-
Has the Hazard been fixed?
-
Contact your Supervisor for further instruction.
-
Inspect For Electrical Hazards
-
Has the Hazard been fixed?
-
Contact your Supervisor for further instruction.
-
Inspect Unit for Hot Surfaces
-
Has the Hazard been fixed?
-
Contact your Supervisor for further instruction.
Preliminary Machine Inspection
-
Check Earth Continuity (Electric Machine Only)
-
Has This Been Rectified?
-
Do not Proceed until this has been rectified.
-
Check Cable and Plug for Wear or Damage (If Applicable)
-
Do not Proceed until this has been rectified.
-
Check Valve Clearances and Adjust if Necessary. (Applicable for all Petrol Units when Conducting a Service)
-
Why weren't the Valves Adjusted?
-
Run Machine Up to Establish Current Condition (if able).
-
Current Pressure (PSI)
-
Any Apparent Faults Observed?
-
What Were They?
-
Is the Work being Conducted a Quote or Repair?
-
Is there a Right to Repair Amount?
-
What is the Amount?
-
Please contact your Supervisor for Further Instruction.
-
Contact Supervisor for Further Instruction.
Machine Service
-
Service Requested?
-
Type of Service
- Cold Water Electric
- Cold Water Petrol
- Cold Water Diesel
- Hot Water Electric
- Hot Water Petrol
- Hot Water Diesel
- Heating Cylinder
- Hydraulic
-
Check Float Valve and Water Supply to Unit
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Shut Down Timer Operation
-
How many minutes is it set to?
-
How many minutes is it set to?
-
Check Chemical Injector
-
Check all Switches for Operation
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
-
Amp Draw Under Load
-
Check Float Valve and Water Supply to Unit
-
Tyres Pumped Up?
-
Why Haven't the Tires been Pumped up?
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Chemical Injector
-
Check all Switches for Operation
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
-
Change Engine Oil
-
Why wasn't the Engine Oil Changed?
-
Change Gearbox Oil
-
Why wasn't the Gearbox Oil Changed?
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Replace Spark Plug(s)
-
Why wasn't the Spark Plug(s) Changed?
-
Check Fuel Filter
-
Replace Oil Filter
-
Why wasn't the Oil Filter Changed?
-
Replace Air Filter
-
Why wasn't the Air Filter Changed?
-
Check Battery - Voltage Reading
-
Check and Adjust Belt Tension
-
Inspect Pull Start Recoil & Rope
-
Cleaned Fuel Bowl?
-
Why wasn't the Fuel Bowl Cleaned?
-
Check Exhaust and Exhaust Bolts
-
Check Float Valve and Water Supply to Unit
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Chemical Injector
-
Check all Switches for Operation
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
-
Change Engine Oil
-
Why wasn't the Engine Oil Changed?
-
Change Gearbox Oil
-
Why wasn't the Gearbox Oil Changed?
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Check Fuel Filter
-
Replace Oil Filter
-
Why wasn't the Oil Filter Changed?
-
Replace Air Filter
-
Why wasn't the Air Filter Changed?
-
Check Battery - Voltage Reading
-
Check and Adjust Belt Tension
-
Inspect Pull Start Recoil & Rope
-
Check Float Valve and Water Supply to Unit
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Shut Down Timer Operation
-
How many minutes is it set to?
-
How many minutes is it set to?
-
Check Chemical Injector
-
Check all Switches for Operation
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
-
Are There any Diesel Leaks?
-
Have the Leaks been Fixed?
-
Clean/Replace Fuel Filter
-
Clean Fuel Pump Filter
-
Clean Burner Electrodes & Adjust if Necessary
-
Why weren't the Electrodes Cleaned and Adjusted?
-
Replace Burner Nozzle
-
Why wasn't the Burner Nozzle Changed?
-
Check & Adjust Fuel Pressure
-
Fuel Pressure? (BAR)
-
Why wasn't the Fuel Pressure Checked?
-
Check Burner Air flow and Adjust if Necessary
-
Why wasn't the Burner Airflow Checked?
-
Lubricate Pressure/Flow Switch and Check Operation
-
Replace Drive Dog
-
Why wasn't the Drive Dog Replaced?
-
Check Fuel Lines
-
Amp Draw Under Load
-
Check Float Valve and Water Supply to Unit
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Chemical Injector
-
Check all Switches for Operation
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
-
Change Engine Oil
-
Why wasn't the Engine Oil Changed?
-
Change Gearbox Oil
-
Why wasn't the Gearbox Oil Changed?
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Replace Spark Plug(s)
-
Why wasn't the Spark Plug(s) Changed?
-
Check Fuel Filter
-
Replace Oil Filter
-
Why wasn't the Oil Filter Changed?
-
Replace Air Filter
-
Why wasn't the Air Filter Changed?
-
Check Battery - Voltage Reading
-
Check and Adjust Belt Tension
-
Inspect Pull Start Recoil & Rope
-
Cleaned Fuel Bowl?
-
Why wasn't the Fuel Bowl Cleaned?
-
Check Exhaust and Exhaust Bolts
-
Are There any Diesel Leaks?
-
Have the Leaks been Fixed?
-
Clean/Replace Fuel Filter
-
Clean Fuel Pump Filter
-
Clean Burner Electrodes & Adjust if Necessary
-
Why weren't the Electrodes Cleaned and Adjusted?
-
Replace Burner Nozzle
-
Why wasn't the Burner Nozzle Changed?
-
Check & Adjust Fuel Pressure
-
Fuel Pressure? (BAR)
-
Why wasn't the Fuel Pressure Checked?
-
Check Burner Air flow and Adjust if Necessary
-
Why wasn't the Burner Airflow Checked?
-
Lubricate Pressure/Flow Switch and Check Operation
-
Replace Drive Dog
-
Why wasn't the Drive Dog Replaced?
-
Check Fuel Lines
-
Check Float Valve and Water Supply to Unit
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Chemical Injector
-
Check all Switches for Operation
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
-
Change Engine Oil
-
Why wasn't the Engine Oil Changed?
-
Change Gearbox Oil
-
Why wasn't the Gearbox Oil Changed?
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Check Fuel Filter
-
Replace Oil Filter
-
Why wasn't the Oil Filter Changed?
-
Replace Air Filter
-
Why wasn't the Air Filter Changed?
-
Check Battery - Voltage Reading
-
Check and Adjust Belt Tension
-
Inspect Pull Start Recoil & Rope
-
Are There any Diesel Leaks?
-
Have the Leaks been Fixed?
-
Clean/Replace Fuel Filter
-
Clean Fuel Pump Filter
-
Clean Burner Electrodes & Adjust if Necessary
-
Why weren't the Electrodes Cleaned and Adjusted?
-
Replace Burner Nozzle
-
Why wasn't the Burner Nozzle Changed?
-
Check & Adjust Fuel Pressure
-
Fuel Pressure? (BAR)
-
Why wasn't the Fuel Pressure Checked?
-
Check Burner Air flow and Adjust if Necessary
-
Why wasn't the Burner Airflow Checked?
-
Lubricate Pressure/Flow Switch and Check Operation
-
Replace Drive Dog
-
Why wasn't the Drive Dog Replaced?
-
Check Fuel Lines
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Check High Pressure Hose for Wear
-
Check all Switches for Operation
-
Are There any Diesel Leaks?
-
Have the Leaks been Fixed?
-
Clean/Replace Fuel Filter
-
Clean Fuel Pump Filter
-
Clean Burner Electrodes & Adjust if Necessary
-
Why weren't the Electrodes Cleaned and Adjusted?
-
Replace Burner Nozzle
-
Why wasn't the Burner Nozzle Changed?
-
Check & Adjust Fuel Pressure
-
Fuel Pressure? (BAR)
-
Why wasn't the Fuel Pressure Checked?
-
Check Burner Air flow and Adjust if Necessary
-
Why wasn't the Burner Airflow Checked?
-
Lubricate Pressure/Flow Switch and Check Operation
-
Replace Drive Dog
-
Why wasn't the Drive Dog Replaced?
-
Check Fuel Lines
-
Amp Draw
-
Check Float Valve and Water Supply to Unit
-
Clean Water Filter
-
Replace High Pressure Nozzle
-
Why wasn't the Nozzle Replaced?
-
Check High Pressure Hose, Gun and Accessories for Leaks and Wear
-
Change Pump Oil
-
Why wasn't the Pump Oil Changed?
-
Check Bypass Valve Operation & Adjust If Needed
-
Are There any Water Leaks?
-
Have the Leaks been Fixed?
-
Are There any Oil Leaks?
-
Have the Leaks been Fixed?
-
Check Chemical Injector
-
Remove Head, Check Seals and Valves
-
Replaced Valve O'Rings?
-
Replaced Valve Cap O'Rings?
-
Replaced Seal O'Rings?
Machine Repair
-
Repair Requested?
-
After running the Machine up what are the apparent problem(s)
-
What is the Action(s) taken to rectify this problem?
-
Is a Service recommended for this Machine?
-
AMP Draw?
-
AMP Reading
Final Inspection
-
Run Machine up without it's Cover
-
Are there any Leaks?
-
Have the Leaks been Fixed?
-
Is the Pump Producing the Correct Pressure?
-
Pump Pressure
-
Is the Machine in Good Working Order?
-
Machine Cleaned?
-
Machine Hours (if known)
-
Job Comments
Admin
-
Part Numbers used
-
Picture(s) of Old Parts
-
Picture(s) of New Parts Used
-
Labour
-
Warranty Work?
Customer Sign Off
-
Customer Signature (Onsite Only)
-
Stop Time