Product Audit, JF

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [10000041927 420cc 13.5 HP E/S]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

**CS Models Only

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
[BEN] PN: 392061
[BMN1] PN: 365281
[BMNB] PN: 365281
[BMNC] PN: 365281
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
[BMN2] Chipper chute & guard
Collection bag (2.5 bushels)
Discharge deflector
Hopper guard & Hopper (2 foam pcs - narrow side)
Bracket
Support guard
Shredder guard assembly bolted together in correct order
Cap nuts on axle
Nylon lock nuts
Lock-tite applied to bolts
[BMN1] Leg support
Hose clamp
Side plate housing
Nylon locks engaged
IDENTIFICATION & PACKAGING
TQC Markings where required
All zip ties present and secure
Decals:
Engine x 4
DR logo
Danger
Data
Prop65 (under data decal)
[BMNB] Engine x 5
[BMNC] Base x 4
Chute
Hopper
[BMN2] Barcode x 2
Assembly box
Chute
Hopper
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Carton (tape top / bottom in "H" pattern), Inserts #1, #2, #3
UI sheet taped on top of engine
Gas tank foam
Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions
[BMN2] Cardboard 1/2 piece placed over hopper
[BEN] Keys zip tied to unit
[BMN1] Small bag - hardware, Large bag - paperwork
[BMNB] Small bag - hardware, Large bag - paperwork
Assembly box , box, inserts
Oil in large bag
[BMNC] Small bag - hardware, Large bag - paperwork
Hopper & Chute stacked and zip tied at each end to pallet

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Engine
On frame
Clutch & Belt
Clutch key in engine shaft
PartN: [######]
Base support
J Hammer x 4 (alternate direction) **CS Models Only
Axle set correctly to base
Flywheel assembly spins freely
Tow bar assembly
On axle & support to tow bar
Frame assembly
On Axle & tow bar
Scroll housing assembly
Chute assembly
Hopper assembly
Wire harness
Battery (secured w/ bracket), pad, and wires
Knife plate
Wheels
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Engine
DR logo
Danger
Data
Prop65 (under data decal)
Base
Chute
Hopper
Barcode
Assembly box
Pallet:
1 unit per pallet w/ important decal on top of box after tapped shut
Box plywood base
Gas tank foam, Top foam
Kit:
Hardware, Engine manual, AO manual, Parts ship, Unpack instructions

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck (26" priemier)
Engine [13.3rato - DMN] [10.5 HP Briggs - BMN]
Muffler (with heat barrier),
Fuel tank (hose clamp on tank)
Battery
Brush bar
Tow ball hitch
Correct Pulley Transaxle
Pulley Idler
Belt (1/2 x 34")
Belt AK50 (1/2 x 52") & Belt drive guide
Throttle (60")
Traction drive cables
Control panel (AT4 Premier)
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Rail bolts, Brush guard bolts, Back flap bolts
Handlebar bolts, Control Panel bolts, Throttle bolts
Crank bolt (torque to 50 ft/lbs)
Idler Housing bolts
Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing)
Star washers used on engine bolts
Correct Belt Routing (if applicable)
Belt guide x 2 correct location
Belt guide not rubbing
Cables routed correctly
Idler Arms move freely
Fuel tank to rear of engine
L bracket attached to Transaxle
Transaxle cable drive
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Throttle panel attached to frame, adjusted & attached to frame
Blade engagement on left bar
Traction handle on right bar
Wire harness plugged in & Battery unplugged
Spring (attached 2nd hole from engine)
Traction drive set,
Grease Zerks
Wheel assy snow hog
Tires inflated & attached correctly (wood blocks)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals
Prop 65 decals (engine & crate), QR Code
Emmissions, DR decal on bed Hopper, Deck Dump lever
Engine (caution, warning) Handlebar,
Traction drive control panel
Add oil, Hot, Danger
Field & brush
Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kits: OP & AO manual, engine manual, unpacking instr., hardware, belt guard, knob set,
jack, bungee, key, gold bolt, hitch clip

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck ( )
Engine [ ] [ ]
Muffler (with heat barrier),
Fuel tank (hose clamp on tank)
Battery
Brush bar
Tow ball hitch
Correct Pulley Transaxle
Pulley Idler
Belt ( )
Belt AK50 ( ) & Belt drive guide
Throttle ( )
Traction drive cables
Control panel ( )
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Rail bolts, Brush guard bolts, Back flap bolts
Handlebar bolts, Control Panel bolts, Throttle bolts
Crank bolt (torque to 50 ft/lbs)
Idler Housing bolts
Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing)
Star washers used on engine bolts
Correct Belt Routing (if applicable)
Belt guide x 2 correct location
Belt guide not rubbing
Cables routed correctly
Idler Arms move freely
Fuel tank to rear of engine
L bracket attached to Transaxle
Transaxle cable drive
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Throttle panel attached to frame, adjusted & attached to frame
Blade engagement on left bar
Traction handle on right bar
Wire harness plugged in & Battery unplugged
Spring (attached 2nd hole from engine)
Traction drive set,
Grease Zerks
Wheel assy snow hog
Tires inflated & attached correctly (wood blocks)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals
Prop 65 decals (engine & crate), QR Code
Emmissions, DR decal on bed Hopper, Deck Dump lever
Engine (caution, warning) Handlebar,
Traction drive control panel
Add oil, Hot, Danger
Field & brush
Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kits: OP & AO manual, engine manual, unpacking instr., hardware, belt guard, knob set,
jack, bungee, key, gold bolt, hitch clip

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck ( )
Engine [ ] [ ]
Muffler (with heat barrier),
Fuel tank (hose clamp on tank)
Battery
Brush bar
Tow ball hitch
Correct Pulley Transaxle
Pulley Idler
Belt ( )
Belt AK50 ( ) & Belt drive guide
Throttle ( )
Traction drive cables
Control panel ( )
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Rail bolts, Brush guard bolts, Back flap bolts
Handlebar bolts, Control Panel bolts, Throttle bolts
Crank bolt (torque to 50 ft/lbs)
Idler Housing bolts
Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing)
Star washers used on engine bolts
Correct Belt Routing (if applicable)
Belt guide x 2 correct location
Belt guide not rubbing
Cables routed correctly
Idler Arms move freely
Fuel tank to rear of engine
L bracket attached to Transaxle
Transaxle cable drive
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Throttle panel attached to frame, adjusted & attached to frame
Blade engagement on left bar
Traction handle on right bar
Wire harness plugged in & Battery unplugged
Spring (attached 2nd hole from engine)
Traction drive set,
Grease Zerks
Wheel assy snow hog
Tires inflated & attached correctly (wood blocks)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals
Prop 65 decals (engine & crate), QR Code
Emmissions, DR decal on bed Hopper, Deck Dump lever
Engine (caution, warning) Handlebar,
Traction drive control panel
Add oil, Hot, Danger
Field & brush
Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kits: OP & AO manual, engine manual, unpacking instr., hardware, belt guard, knob set,
jack, bungee, key, gold bolt, hitch clip

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck ( )
Engine [ ] [ ]
Muffler (with heat barrier),
Fuel tank (hose clamp on tank)
Battery
Brush bar
Tow ball hitch
Correct Pulley Transaxle
Pulley Idler
Belt ( )
Belt AK50 ( ) & Belt drive guide
Throttle ( )
Traction drive cables
Control panel ( )
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Rail bolts, Brush guard bolts, Back flap bolts
Handlebar bolts, Control Panel bolts, Throttle bolts
Crank bolt (torque to 50 ft/lbs)
Idler Housing bolts
Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing)
Star washers used on engine bolts
Correct Belt Routing (if applicable)
Belt guide x 2 correct location
Belt guide not rubbing
Cables routed correctly
Idler Arms move freely
Fuel tank to rear of engine
L bracket attached to Transaxle
Transaxle cable drive
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Throttle panel attached to frame, adjusted & attached to frame
Blade engagement on left bar
Traction handle on right bar
Wire harness plugged in & Battery unplugged
Spring (attached 2nd hole from engine)
Traction drive set,
Grease Zerks
Wheel assy snow hog
Tires inflated & attached correctly (wood blocks)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals
Prop 65 decals (engine & crate), QR Code
Emmissions, DR decal on bed Hopper, Deck Dump lever
Engine (caution, warning) Handlebar,
Traction drive control panel
Add oil, Hot, Danger
Field & brush
Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kits: OP & AO manual, engine manual, unpacking instr., hardware, belt guard, knob set,
jack, bungee, key, gold bolt, hitch clip

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck ( )
Engine [ ] [ ]
Muffler (with heat barrier),
Fuel tank (hose clamp on tank)
Battery
Brush bar
Tow ball hitch
Correct Pulley Transaxle
Pulley Idler
Belt ( )
Belt AK50 ( ) & Belt drive guide
Throttle ( )
Traction drive cables
Control panel ( )
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Rail bolts, Brush guard bolts, Back flap bolts
Handlebar bolts, Control Panel bolts, Throttle bolts
Crank bolt (torque to 50 ft/lbs)
Idler Housing bolts
Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing)
Star washers used on engine bolts
Correct Belt Routing (if applicable)
Belt guide x 2 correct location
Belt guide not rubbing
Cables routed correctly
Idler Arms move freely
Fuel tank to rear of engine
L bracket attached to Transaxle
Transaxle cable drive
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Throttle panel attached to frame, adjusted & attached to frame
Blade engagement on left bar
Traction handle on right bar
Wire harness plugged in & Battery unplugged
Spring (attached 2nd hole from engine)
Traction drive set,
Grease Zerks
Wheel assy snow hog
Tires inflated & attached correctly (wood blocks)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals
Prop 65 decals (engine & crate), QR Code
Emmissions, DR decal on bed Hopper, Deck Dump lever
Engine (caution, warning) Handlebar,
Traction drive control panel
Add oil, Hot, Danger
Field & brush
Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kits: OP & AO manual, engine manual, unpacking instr., hardware, belt guard, knob set,
jack, bungee, key, gold bolt, hitch clip

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck ( )
Engine [ ] [ ]
Muffler (with heat barrier),
Fuel tank (hose clamp on tank)
Battery
Brush bar
Tow ball hitch
Correct Pulley Transaxle
Pulley Idler
Belt ( )
Belt AK50 ( ) & Belt drive guide
Throttle ( )
Traction drive cables
Control panel ( )
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Rail bolts, Brush guard bolts, Back flap bolts
Handlebar bolts, Control Panel bolts, Throttle bolts
Crank bolt (torque to 50 ft/lbs)
Idler Housing bolts
Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing)
Star washers used on engine bolts
Correct Belt Routing (if applicable)
Belt guide x 2 correct location
Belt guide not rubbing
Cables routed correctly
Idler Arms move freely
Fuel tank to rear of engine
L bracket attached to Transaxle
Transaxle cable drive
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Throttle panel attached to frame, adjusted & attached to frame
Blade engagement on left bar
Traction handle on right bar
Wire harness plugged in & Battery unplugged
Spring (attached 2nd hole from engine)
Traction drive set,
Grease Zerks
Wheel assy snow hog
Tires inflated & attached correctly (wood blocks)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals
Prop 65 decals (engine & crate), QR Code
Emmissions, DR decal on bed Hopper, Deck Dump lever
Engine (caution, warning) Handlebar,
Traction drive control panel
Add oil, Hot, Danger
Field & brush
Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kits: OP & AO manual, engine manual, unpacking instr., hardware, belt guard, knob set,
jack, bungee, key, gold bolt, hitch clip

Tires inflated & attached correctly (wood blocks) Parts properly oriented
Cables routed correctly Belt routed correctly
L bracket attached to Transaxle Transaxle cable drive
Throttle adjusted & attached to frame
Shift bracket mounted to Transaxle (2 shift cables attached from bottom of bracket)
Blade engagement on left bar, traction handle on right bar
Belt guide not rubbing
Wire harness plugged in, Battery unplugged
Ground wire to top-left, star lock washer under bolt head
Solenoid fastened under battery bracket

Handlebar bolts Control Panel bolts Throttle bolts
Rail bolts, Brush guard bolts, Back flap bolts Idler Housing bolts, Lug nuts
Nut (Belt cover, under deck, side panel, idler arm, flywheel housing, etc.)
Identification & Packaging
TQC Markings where required. All zip ties present and secure.

Prop 65 decals (engine & crate) QR Code
Emmissions, DR decal on bed Hopper
Deck Dump lever, Traction drive control panel
Engine (caution, warning), EPA [A0000279125]
Handlebar, Add oil, Hot Danger
Field & brush
*[BENC= Sound power cable CE]

Deck assembled to frame
Blade engage lever adjusted correctly
Belt guide x 2 correct location and belt inside guides Throttle panel attached to frame
Accessory box zip tied to crate
All zip ties present and secure (handle, hoses, axle, kit box, belt guide, brake lines, etc)

Pallet *[BENC= Heat treated]
Crate assembly (check sides, unit secure, accessory box) (side x 2, ends x 2, top) *[BENC= Crate Heat treated]
Kits: operating manual, engine manual, unpacking instr., AO manual, hardware, key
[BEN= knob set] [BENC= EC Declaration]

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
Deck
Engine
ASSEMBLY
Parts are assembled in correct orientation
Blade/spindle assy, Blade engage lever adjusted correctly
Deck assembled to frame, Deck guard assy
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
Cables routed correctly
Grease Zerks
Tires inflated & attached correctly
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure. (handle, hoses, axle, kit box, belt guide, brake lines, etc)
Decals:

Accessory box zip tied to crate Pallet
Crate assembly (long side, short side, top) (check sides, unit secure)
Kit -

details needed

details needed

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PAPARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [0H9838G 420cc]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [100000036466]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [0H0957]
Roll over valve present
Hang tag [0H0176]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [0H9112B, 0H8251B]
Record safety decals [0H0115D, 0H0116B, 0H4635C, 0H2549E]
Emissions [A0000256021]
Engine family
Evaporative (Carb units only) [JGNXECMPORT3]
Ground [067210D]
Hy-pot [0G97400]
Alternator [0K0755]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [10000029705]
Registration card
Warranty [0K2521C, 10000033356]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [10000020426]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [10000032556]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [0K4837]
Handle
Wheel
Magnetic sensor [0K7304]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [10000027730]
Cord extension 25ft [10000029119]
85P brand specific 8KW Co w/cord carb [10000031790]
Packaging fuel tank cover GP [10000033467]
Carton insert GP [10000033589]
Carton loose parts [10000033597]
Decals:
Cord 25ft, 20amp [10000029119]
Generac logo GP [10000032939]
Badge CO sense GP [10000033027]
Co-sense action label [10000033027]
Box carb. Prop65 x 2 [10000035819]
Muffler (on gas tank) [0K9502A]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts: 120/240
Amps: 66.6/33.3
Frequency: 60
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

PARTS & SPECIFICATIONS
Paint free of runs & overspray
No scratches/light spots (EDS59 compliant)
No deformation
Correct fit
Welds uniform & complete
ASSEMBLY
Engine
Engine model [ ]
Displacement
No rust or debris in fuel tank
Engine fill cap and dipstick has o-ring
Wires
Wiring not pinched behind cover
Battery cables positioned correctly
No wires are near the rotor bolt
Ground connections are tight
Control Panel [ ]
Meets wiring standard
Secure and not damaged
GFCI functions correctly
Battery charger functions
Fasteners
Correct fasteners present & secure
Star washers oriented correctly
Screws are tight, heads not stripped
Fuel & Oil Lines
Hose clamps positioned properly & secure
Fuel line & filter not rubbing on other parts
Fuel line not kinked
Fuel cap tethered
Carbon canister present [ ]
Roll over valve present
Hang tag [ ]
IDENTIFICATION & PACKAGING
Decals:
Decals present (per eng drawing) [ ]
Record safety decals [ ]
Emissions [ ]
Engine family
Evaporative (Carb units only) [ ]
Ground [ ]
Hy-pot [ ]
Alternator [ ]
No air bubbles or damage on decals
Data plate correct (per BOM)
Kit:
Owner’s manual [ ]
Registration card
Warranty [ ]
Correct parts in accessory bag
Components have mating surface on frame (fit up)
Battery charger [ ]
Unit clean (no scratches, dents, oxidation)
Check ID on unit & packaging
Carton part [ ]
Carton clean, undamaged, & taped correctly
Carton decals are correct & attached straight
Verify all wood components are dry [ ]
Handle
Wheel
Magnetic sensor [ ]
TESTING & PERFORMANCE
Verify test data
No unusual noise
LOS shuts down properly
Recoil operational
ON/OFF circuit test
Idle control functions
Generator performs per spec
After Run Checks
No oil or fuel leaks
Oil color is amber
Correct engineering drawing in boxing area
Fuel On/Off valve installed at boxing
Oil removed in boxing
CSA:
IMPORTED UNITS
Color sample vs color chip
Serial corresponds to PO
Module CO Port Gen [ ]
Cord extension 25ft [ ]
85P brand specific 8KW Co w/cord carb [ ]
Packaging fuel tank cover GP [ ]
Carton insert GP [ ]
Carton loose parts [ ]
Decals:
Cord 25ft, 20amp [ ]
Generac logo GP [ ]
Badge CO sense GP [ ]
Co-sense action label [ ]
Box carb. Prop65 x 2 [ ]
Muffler (on gas tank) [ ]

TESTING
Required tools/ gauges (in calibration)
Current test procedures & EDS
Specifications
Volts:
Amps:
Frequency:
Test Dot/Tester: N/A

OBSERVATIONAL TEST Procedure
No Load (volts, frequency)
1/2 Load (volts, amps, frequency)
Full Load (volts, amps, frequency)
Outlet Plug (P/F)

EXTENDED TEST Procedure
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)
5 mins: No Load (volts, frequency)
15 mins: 90% Load (volts, amps, frequency)

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Bolts in forward mounting holes
Lawn deck frame:
Frame assembly and attachment
Height adjustment plate to frame
Front/rear link plates attached
Rod shaft hangers attached
Side chute assembly on front
Mulching kit assembly
2 front rod hangers w/bushing toward roll pin
Lever height adjust to front rod hanger
2 rear rod hangers assembled securely to frame
Idler arm assembly installed on lawn deck
Pulleys and guards assembly
Lawn mower blades installed
Blade spindle pulleys installed
Bracket vortex baffle installed
Wheels/Tires:
Tire on axle valve stem facing out (inflated) x2
Wheel bushing into frame x4
Anti-scalping wheels
L/R anti-scalp bracket (each side)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Danger
Informational & Safety (on lawn deck)
DR logo (5.75" to center of belt cover)
Cutting height (adjacent to height adjustment lever)
CE Declaration
Pallet:
Box 42x42
Lawn deck into box bottom
Insert between frame & wheel mounts
Tires centered between frame wheel mounts
Box insert 42" x 2
Box angle insert
Staple box insert
6 staples on box bottom flaps (24 total)
Top on box

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Bolts in forward mounting holes
Lawn deck frame:
Frame assembly and attachment
Height adjustment plate to frame
Front/rear link plates attached
Rod shaft hangers attached
Side chute assembly on front
Mulching kit assembly
2 front rod hangers w/bushing toward roll pin
Lever height adjust to front rod hanger
2 rear rod hangers assembled securely to frame
Idler arm assembly installed on lawn deck
Pulleys and guards assembly
Lawn mower blades installed
Blade spindle pulleys installed
Bracket vortex baffle installed
Wheels/Tires:
Tire on axle valve stem facing out (inflated) x2
Wheel bushing into frame x4
Anti-scalping wheels
L/R anti-scalp bracket (each side)
IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.
Decals:
Danger
Informational & Safety (on lawn deck)
DR logo (5.75" to center of belt cover)
Cutting height (adjacent to height adjustment lever)
CE Declaration
Pallet:
Box 42x42
Lawn deck into box bottom
Insert between frame & wheel mounts
Tires centered between frame wheel mounts
Box insert 42" x 2
Box angle insert
Staple box insert
6 staples on box bottom flaps (24 total)
Top on box

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Base weldment assembly
Idler and Lever assembly
Belt release assembly
Wear plate and bearing assemblies
Flywheel assembly
Pulley Assembly (verify key is installed)
IDENTIFICATION & PACKAGING
TQC Markings where required
All zip ties present and secure
Decals:
Danger x 1 [241801]
Danger x 3 [247961] (on chute)
Access Plate [247971]
Rotation Parts x 2 (on belt guard assembly)
Do Not Remove [247981]
Pallet:
Box [264311]
Deflector hopper assembly to box
Box inserts [264341] [264321] [264331]
Prop65 decals on outside of box

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.
ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
IDENTIFICATION & PACKAGING
TQC Markings where required
All zip ties present and secure
Decals:

Pallet:

PARTS & SPECIFICATIONS
Frame Welds & Paint
Good welds: no burrs , no burns
Motor mounting rails formed and welded correctly
Frame holes clear and free from paint buildup
No scratches or light spots in paint (EDS 59 compliant)
Motor mounting plate painted and formed correctly
Motor mounting rail mounting holes on correct side
Housing defect free (short shots, cold shots, knit lines, porosity)
Wheel/Axel
Clean and cosmetically good.
ASSEMBLY
Pump mounting bolts torqued to specs (15 ft/lbs +/- 10%) [0K1663]
Wheel & Axel [0J6276, 10000025911]
(2) snap buttons assembled to inside of frame
Engine
Engine to base hardware is tight.

Decals:
Quick start decal x2 [0K6007, 0J3374]
Engine & engine size decal on recoil cover [10000021481]
Emissions decal w/correct family name on engine
"Throttle" decal
"Danger" decal
"ON/OFF" decal
Yellow oil fill tag attached to tank
Bar code decal present and matches engine serial #

4.0 Pump & Pump Assembly

5.0 ASM chem. tank, vibration pad, & foot to frame
Foot billboard free from molding and cosmetic flaws.
Foot attached securely with mounting bolts
Data label attached w/overlay & no air bubbles under data label
Inspect frame for signs of frame twisting
Tank(s), tank cap(s) securely attached [0L4734, 10000022233, 0I2091]

6.0 Oil fill
Unit filled with oil

7.0 Observational Test (Observe 1 unit alternating stands)
Observe Test Unit for Cosmetic & Functional Defects.
Test Parameters: 10000007200 0K2696: Yellow Model # 6602-1
Pressure: 2400 - 2450 Flow: 2.5 RPM: 3800 - 3850 Vac min: 15
Test cell operator green dot present.

8.0 Unit prep
End of fuel line free from splits. Fuel line and clamps attached.
Unit clean, handle and engine wiped as needed.
Pump ends have plug caps attached. Oil cap present.

9.0 Upper frame and billboard assembly
Upper billboard and bars assembled w/ 4 fasteners
Molded components complete and free from defects
Billboard label attached, straight, w/no bubbles [0K1286A, 0K1287A]
Correct nozzle label attached to billboard.
Nozzle grommets attached to billboard
Upper handle assy. packed per spec (prevents scuffs & scratches)

10.0 Gun and attachments (check for fit, labels)
Fittings work (gun, hose, pump, nozzle, lance)
[0H9640, 0H9617R, 10000021487]
Lances (wands) free of metal chips and burrs
[0K2521C, 0K2895, 0L3579A, 0L5832, 0L6431,1000000823]
(3) labels present on guns, good alignment
Kit Bag: owner's manual, 3 registration cards, funnel, cap, nozzle kit
[10000007126, 10000022150, 0K2521C, 10000021532]

11.0 Packaging (verify correct packaging, quality)
Engine free from scratches, dents, nicks, oxidation.
Engine touch up paint as needed.
Shadow board used at pack.
All labels are present per labeling print. Correct data label and emission label.
Top insert stapled, Hose hook attached to insert
Wood pallets are dry & undamaged: [10000000483]
Carton: [10000021504] Manual:: [10000021513, 10000021532]

12.0 Extended Test
Check running unit for loose/vibrating components and leaks.
Correct Data & Emissions Label.
Test: 3 min - Gun Off, 15 min - Gun On, 3 min - Gun Off, 15 min - Gun On
Pressure: 2400 - 2450 Flow: 2.5 RPM: 3800 - 3850 Vacuun Draw min: 15

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

1.0 Frame Welds & Paint [10000000941]
Good welds- No burrs , No burn through
Frame holes clear and free from paint buildup
No scratches or light spots in paint compliant to EDS 59
Motor mounting plate painted & formed correctly
Motor mounting rails formed and welded correctly

2.0 Wheel & Axel Assembly
Wheels/axle assembled correctly [0J6276, 100000251533].
Wheels/axle clean and cosmetically good [0K99874]
(2) quick start labels attached [0K6007, 0J3374]
(2) snap buttons assembled to inside of frame [0G5442]

3.0 Engine & Engine Assembly
Correct engine & engine size decal on recoil cover [0K8430 196cc]
Throttle label, "Danger", "ON/OFF labels present
Yellow oil fill tag attached to tank [To be taped to engine]
Emissions decal w/correct family name on engine
Bar code label present and matches engine serial #
Verify engine to base hardware is tight [10000037322 Prop 65]

4.0 Pump & Pump Assembly *Hand start pump bolts
Pump mounting bolts torqued to spec (15 ftlbs +/- 10%) [10000042904]]
Housing defect free (short shots, cold shots, knit lines, porosity)
Bar code label present on pump.

5.0 ASM chem. tank, vibration pad, & foot to frame
Data label attached w/overlay & no air bubbles under data label
Inspect frame for signs of frame twisting
Tank(s), tank cap(s) securely attached [0L2091 - DO NOT USE BLEACH]

6.0 Oil fill
Unit filled with oil

7.0 Observational Test (Observe 1 unit alternating stands)
Observe Test Unit for Cosmetic & Functional Defects.
* Test Parameters: 10000045854] Nozzle: Red29 Model # 7954-0
* Pressure: 2340 - 2380 Flow: 2.4 RPM: 3800 - 3850 Vac min: 15
Test cell operator green dot present.

8.0 Unit prep
End of fuel line free from splits. Fuel line and clamps attached.
Pump ends have plug caps attached. Oil cap present.
Unit clean, handle and engine wiped as needed.

9.0 Upper frame and billboard assembly
Upper billboard and bars assembled w/ 4 fasteners
Molded components complete and free from defects
Billboard label attached, straight, w/no bubbles
Correct nozzle label attached to billboard [0L4737, 10000045893]
Nozzle grommets attached to billboard [0J3079]
Upper handle assy. packed per spec (prevents scuffs & scratches)

10.0 Gun and attachments (check for fit, labels)
Fittings work (gun, hose, pump, nozzle, lance) [0H9642A, 0K0921]
Lances (wands) free of metal chips and burrs [0H9640]
(3) labels present on guns, good alignment
Bag: owner's manual, 3 registration cards, nozzle kit
[0K1388, 0L4738] [0H9617A, 10000042081]
Hose hook [0K2521C, 0J3020]
Fasteners [0J1449]

11.0 Packaging (verify correct packaging, quality)
Engine free from scratches, dents, nicks, oxidation.
Engine touch up paint as needed.
Shadow board used at pack.
All labels are present per labeling print. Correct data label and emission label.
Top insert w/ pump insert stapled
Wood pallets are dry & undamaged: [10000000483]
Carton: [10000045887] Manual:: [0L5053]
Box scale functions properly & used correctly

12.0 Extended Test
Check running unit for loose/vibrating components and leaks.
Correct Data & Emissions Label.
Test: 3 min - Gun Off, 15 min - Gun On, 3 min - Gun Off, 15 min - Gun On
Pressure: 2340 - 2380 Flow: 2.4 RPM: 3800 - 3850 Vacuun Draw min: 15

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

1.0 Frame Welds & Paint [10000000941]
Good welds- No burrs , No burn through
Frame holes clear and free from paint buildup
No scratches or light spots in paint compliant to EDS 59
Motor mounting plate painted & formed correctly
Motor mounting rails formed and welded correctly

2.0 Wheel & Axel Assembly
Wheels/axle assembled correctly [0J6276, 100000251533].
Wheels/axle clean and cosmetically good
(2) quick start labels attached [0K6007, 0J3374]
(2) snap buttons assembled to inside of frame [0G5442]

3.0 Engine & Engine Assembly
Correct engine & engine size decal on recoil cover [0K8430 196cc]
Throttle label, "Danger", "ON/OFF labels present
Yellow oil fill tag attached to tank
Emissions decal w/correct family name on engine [0K2668A]
Bar code label present and matches engine serial #
Verify engine to base hardware is tight

4.0 Pump & Pump Assembly *Hand start pump bolts
Pump mounting bolts torqued to spec (15 ftlbs +/- 10%) [10000037099]
Housing defect free (short shots, cold shots, knit lines, porosity)
Bar code label present on pump. [37099 - Last 5 of serial number]

5.0 ASM chem. tank, vibration pad, & foot to frame
Data label attached w/overlay & no air bubbles under data label
Inspect frame for signs of frame twisting
Tank(s), tank cap(s) securely attached [0L2091 - DO NOT USE BLEACH]
[0K4078A, 0L4734]

6.0 Oil fill
Unit filled with oil

7.0 Observational Test (Observe 1 unit alternating stands)
Observe Test Unit for Cosmetic & Functional Defects.
* Test Parameters: 10000007200] Nozzle: 25 black w/white
* Pressure: 2525 - 2575 Flow: 2.4 RPM: 3800 - 3850 Vac min: 15
Test cell operator green dot present.

8.0 Unit prep
End of fuel line free from splits. Fuel line and clamps attached.
Pump ends have plug caps attached. Oil cap present.
Unit clean, handle and engine wiped as needed.

9.0 Upper frame and billboard assembly [10000000988]
Upper billboard and bars assembled w/ 4 fasteners
Molded components complete and free from defects
Billboard label attached, straight, w/no bubbles
Correct nozzle label attached to billboard [0L4740D]
Nozzle grommets attached to billboard [0J3079]
Upper handle assy. packed per spec (prevents scuffs & scratches)

10.0 Gun and attachments (check for fit, labels)
Fittings work (gun, hose, pump, nozzle, lance) [10000009382, 10000036879]
Lances (wands) free of metal chips and burrs [0H9640 Foamer 0L3579] [Turbo Nozzle 0K2895]
(3) labels present on guns, good alignment [card pw acc 10000008335]
Bag: owner's manual, 3 registration cards, nozzle kit [0K1388, 0L6431, 10000042074] [Mesh bag 10000007185]
Funnel [0K2521C] Hose hook [0J3021] Fasteners [0L6782] xmas trees [10000042081]

11.0 Packaging (verify correct packaging, quality)
Engine free from scratches, dents, nicks, oxidation.
Engine touch up paint as needed.
Shadow board used at pack.
All labels are present per labeling print. Correct data label and emission label.
Top insert w/ pump insert stapled
Wood pallets are dry & undamaged: [10000000483 HT]
Carton: [10000042080] Manual:: [0L5053]
Box scale functions properly & used correctly

12.0 Extended Test
Check running unit for loose/vibrating components and leaks.
Correct Data & Emissions Label.
Test: 3 min - Gun Off, 15 min - Gun On, 3 min - Gun Off, 15 min - Gun On
Pressure: 2525 - 2575 Flow: 2.4 RPM: 3800 - 3850 Vac min: 15

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

PARTS & SPECIFICATIONS

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Need details

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements.
Correct part numbers present at correct revision level.

ASSEMBLY
Parts are assembled in correct orientation
Nuts, Bolts, Screws, etc. all present, secure, and properly tightened
Correct Belt Routing (if applicable)

IDENTIFICATION & PACKAGING
TQC Markings where required.
All zip ties present and secure.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

Parts & Specifications
Parts meet all dimensional & fitment requirements. Correct part numbers present at correct revision level.

PARTS & SPECIFICATIONS
Parts meet all dimensional & fitment requirements
Correct part numbers present at correct revision level
Transfer Switch - mechanism & housing (no defects)
Circuit breaker - no defects in switch and/or housing
Wiring harness - no defects or frayed wires (terminal block, fuse holder, relay)
Enclosures - no bad paint, no defects, properly formed
Load Shed Control Board - no visual defects in plastic and/or terminals
wires are tight & strands are captured on terminal connections
ASSEMBLY
Wire harness assembly is correct and has good terminal connections
Fuse block holder all 3 fuses are firmly seated
Amp Service:
100 amp
Lug mounts 24-30 inlb (2-2.5 ftlb) / Large wire connections 50 inlb (4 ftlb)
150 & 200 amp
Lug connectors, buss bars, & heavy wire connectors to 72 inlb (6 ftlb)
TESTING
Unit passes through 2 cycles on the tester
If controller is present, green lights will flash on each cycle
IDENTIFICATION & PACKAGING
Decals are straight and free of bubbles
Operator manual & Warranty

Parts:
Transfer Switch: 0L2911
Circuit Breaker: 0K0971
Grounding (Bus) Bar: 0K0130
Neutral Block Assembly: 0K0108A (0C3623)
Fuse Block Holder: 10000004183
US Wire Harness: 10000005872
Canadian Wire Harness: N/A
Decals:
Fuse Replacement: N/A
UL Listing (Inside Box): N/A
Neutral Bonding (Back Plate): 0K1018
Warning Man Op Handle: 0E3484
UL Sense (Back Plate): 0G0471A
Honeywell (Front Cover): 0K1274
Test Seq (Top Front Plate): 0K1738
Terminal Shock: 0G3259
Service Entrance: 0G9651
Data Decal: 0L1950A
US 2008 NEC (Front Cover Plate): 0H7274
WCR NEC: 10000008602
Prop 65: 10000037322
US Live Circuit (Bottom Front Plate): 0G3274
Canadian Live Circuit (N/A): 0H5388 N/A
Canadian CSA Connection (N/A): 0J2195 N/A
Kit (paperwork):
US Op Manual: 10000009532
US Warranty: 0K3103
Canadian Op Manual: N/A
Canadian Warranty: N/A
Pallet:
Units Per Pallet: 24

Review and Update to Unlisted Model Requirements
Parts:
Transfer Switch: #
Circuit Breaker: #
Grounding (Bus) Bar: #
Neutral Block Assembly: # (#)
Fuse Block Holder: #
US Wire Harness: 10000005872
Canadian Wire Harness: N/A
Decals:
Fuse Replacement: 0D3587 – circuit breakers / 0A9517 – no circuit breakers
UL Listing (Inside Box): 0G0900 - circuit breakers / 081221 - no circuit breakers
Neutral Bonding (Back Plate): 0K1018
Warning Man Op Handle: 0E3484
UL Sense (Back Plate): 0G0471A
Test Seq (Top Front Plate): 0K1738
Terminal Shock: 0G3259
Service Entrance: 0G9651
Data Decal: 0L1950A
US 2008 NEC (Front Cover Plate): 0H7274
WCR NEC: 10000008602
Prop 65: 10000037322
US Live Circuit (Bottom Front Plate): 0G3274
Canadian Live Circuit (Bottom Front Plate): 0H5388
Canadian CSA Connection: 0J2195
Kit (paperwork):
US Op Manual: 10000009532
US Warranty: 0K3103
Canadian Op Manual: N/A
Canadian Warranty: N/A
Pallet:
Units Per Pallet: ##

Parts:
Transfer Switch: 0L2911
Circuit Breaker: 0K0133
Grounding (Bus) Bar: 0K0130
Neutral Block Assembly: 0K0108A (0C3623)
Fuse Block Holder: 10000004183
US Wire Harness: 10000005872
Canadian Wire Harness: N/A
Decals:
Fuse Replacement (N/A): N/A
UL Listing (Inside Box): 0G0900 - circuit breakers / 081221 - no circuit breakers
Neutral Bonding (Back Plate): 0K1018
Warning Man Op Handle: 0E3484
UL Sense (Back Plate): 0G0471A
Honeywell (Front Cover): 0K1274
Test Seq (Top Front Plate): 0K1738
Terminal Shock: 0G3259
Service Entrance: 0G9651
Data Decal: 0L1950A
US 2008 NEC (Front Cover Plate): 0H7274
WCR NEC: 10000008602
Prop 65: 10000037322
US Live Circuit (Bottom Front Plate): 0G3274
Canadian Live Circuit (N/A): N/A
Canadian CSA Connection (N/A): N/A
Kit (paperwork):
US Op Manual: 10000009532
US Warranty: 0K3103
Canadian Op Manual: N/A
Canadian Warranty: N/A
Pallet:
Units Per Pallet: 24

Attach photo(s) of Failure for QN

Attach photo(s) of Failure for QN