INSPECTOR

  • Add signature

VCR's AND OIL SWITCHES

  • APPEARANCE OK

  • BUSHINGS CLEAN, GOOD CONDITION

  • FREE FROM OIL LEAKS

  • COUNTER READINGS RECORDED

AIR-BREAK AND DISCONNECT SWITCHES

  • APPEARANCE OK

  • INSULATORS OK

  • GROUND CONNECTION TO HANDLE OK

BYPASS SWITCHES

  • APPEARANCE OK

  • INSULATORS OK

MISCELLANEOUS ELECTRICAL EQUIPMENT

  • ARRESTER APPEARANCE OK

  • ARRESTER CORRECTLY CONNECTED

  • SWITCH STICKS OK, PROPERLY STORED

  • PHASES PROPERLY IDENTIFIED

  • CIRCUITS PROPERLY IDENTIFIED

  • BUSES AND CONNECTIONS OK

  • BURNED OUT LAMPS REPLACED

  • OVERHEAD GROUND WIRE OK

  • CABINETS AND CUBICLES OK

SAFETY

  • EQUIPMENT GROUNDS OK

  • FENCES AND GATES GROUNDED

  • EXITS, WALKWAYS AND DRIVEWAYS CLEAR

  • SUB ENCLOSURES FREE OF STORED MATERIAL & EQUIPMENT

  • NESC CLEARANCES COMPLIED WITH

  • SUBSTATION AREA PROPERLY LIGHTED

  • YARD CLEAN AND FREE OF WEEDS

  • GATES PROPERLY LOCKED

  • SUITABLE WARNING SIGNS ON FENCES

YARD AND STRUCTURES

  • FENCES AND GATES ADEQUATE

  • YARD PROPERLY SURFACED

  • STRUCTURE PAINT OK

  • FENCE AND GATE PAINT OK

POWER TRANSORMERS

  • APPEARANCE OK

  • BUSHINGS CLEAN,GOOD CONDITION

  • OIL LEVELS AND GAUGES OK

  • FREE FROM OIL LEAKS

  • THERMOMETERS OK, MAXIMUMS RESET

  • AUX. COOLING EQUIPMENT OK

  • GAS PRESSURE OK

REGULATORS

  • APPEARANCE OK

  • BUSHINGS CLEAN, GOOD CONDTION

  • OIL LEVELS AND GAUGES OK

  • FREE FROM OIL LEAKS

  • THERMOMETERS OK, MAXIMUMS RESET

  • MECHANISMS OK

  • INDICATING LIGHTS OK

  • INDICATING GLASS COVERS INTACT

  • CABINET GASKETS WEATHER TIGHT

  • COUNTER READINGS RECORDED

ADDITIONAL COMMENTS

TRANSFORMER

UNIT 69/12.47kv

MANUFACTURE = ( Westinghouse )

SERIAL# ( SJV8261-01 )

TAP SETTING ( 70,600 )

OIL LEVEL

  • OIL TEMP

  • OIL PRESSURE

BUSHING CONDITION

  • BUSHING CONDITION

REGULATORS

DRAG HAND POSITIONS

A-PHASE

  • CURRENT POSITION

  • MINIMUM POSITION

  • MAXIMUM POSITION

  • NUMBER OF OPERATIONS

  • RESET DRAG HANDS

  • MAXIMUM CURRENT

  • POWER FACTOR MAX / MIN

  • KVA MAX

  • OUTPUT VOLTAGE

B-PHASE

  • CURRENT POSITION

  • MINIMUM POSITION

  • MAXIMUM POSITION

  • NUMBER OF OPERATIONS

  • RESET DRAG HANDS

  • MAXIMUM CURRENT

  • POWER FACTOR MAX / MIN

  • KVA MAX

  • OUTPUT VOLTAGE

C-PHASE

  • CURRENT POSITION

  • MINIMUM POSITION

  • MAXIMUM POSITION

  • NUMBER OF OPERATIONS

  • RESET DRAG HANDS

  • MAX CURRENT

  • POWER FACTOR MAX / MIN

  • OUTPUT VOLTAGE

REGULATOR SETTINGS

A-PHASE

  • MANUFACTURE (COOPER) SERIAL # ( 0750015281 TYPE / AMPS ( VR32 B / 100 ) SET VOLTAGE ( 123 ) BAND WIDTH 2 TIME DELAY ( 30 ) LDC R / X ( 2.8 / 2.1 CONTROL TYPE ( CL6 )

B-PHASE

  • MANUFACTURE (COOPER) SERIAL # ( 0750015282 TYPE / AMPS ( VR32 B / 100 ) SET VOLTAGE ( 123 ) BAND WIDTH 2 TIME DELAY ( 30 ) LDC R / X ( 2.8 / 2.1 CONTROL TYPE ( CL6 )

C-PHASE

  • MANUFACTURE (COOPER) SERIAL # ( 0750015283 TYPE / AMPS ( VR32 B / 100 ) SET VOLTAGE ( 123 ) BAND WIDTH 2 TIME DELAY ( 30 ) LDC R / X ( 2.8 / 2.1 CONTROL TYPE ( CL6 )

OIL CIRCUIT RECLOSERS

To find Demand metering amps. 1. Press METERING button, press down arrow to "Demand Metering", arrow down to "Reset Demand Phase Amps", press ENTER, record max demand an d peak amps below. To Reset Demand and Peak Amps 1. Press METERING button, press down arrow to "Demand Metering", arrow down to "Reset Demand Peaks", press F4. "METER ARE RESET" should appear for 2 seconds.

ROUTE No. 1- NOVA TS

  • A- COUNTER READINGS

  • B- COUNTER READINGS

  • C- COUNTER READINGS

  • GRD

  • A-MAX AMPS DEMAND/PEAK

  • B-MAX AMPS DEMAND/PEAK

  • C-MAX AMPS DEMAND/PEAK

ROUT No. 3 - NOVA TS

  • A- COUNTER READINGS

  • B-COUNTER READINGS

  • C-COUNTER READINGS

  • GRD

  • A-MAX AMPS DEMAND/PEAK

  • B-MAX AMPS DEMAND/PEAK

  • C-MAX AMPS DEMAND/PEAK

ROUT No. 4

  • A- COUNTER READINGS

  • B- COUNTER READINGS

  • C- COUNTER READINGS

  • GRD

  • A-MAX AMPS DEMAND/PEAK

  • B-MAX AMPS DEMAND/PEAK

  • C-MAX AMPS DEMAND/PEAK

FORM 6 BATTERY TEST

RT #1 FORM 6

  • DID BATTERY TEST OK

RT #3 FORM 6

  • DID BATTERY TEST OK

During a manual test if the voltage drops below 22.8 volts DC for one full second, the ALARM LED (battery alarm) will ILLUMINATE.

1. Press the MENU button on the front panel. 2. Using the down arrow key, navigate to the BATTERY menu and press ENTER. 3. Using the down arrow key, navigate to the TEST BATTERY menu and press ENTER. 4. Press the f4 button to test the battery. LCD should display: ---Testing---

The templates available in our Public Library have been created by our customers and employees to help get you started using SafetyCulture's solutions. The templates are intended to be used as hypothetical examples only and should not be used as a substitute for professional advice. You should seek your own professional advice to determine if the use of a template is permissible in your workplace or jurisdiction. Any ratings or scores displayed in our Public Library have not been verified by SafetyCulture for accuracy. Users of our platform may provide a rating or score that is incorrect or misleading. You should independently determine whether the template is suitable for your circumstances. You can use our Public Library to search based on criteria such as industry and subject matter. Search results are based on their relevance to your search and other criteria. We may feature checklists based on subject matters we think may be of interest to our customers.