CW Installation. Quality Report.

• Site conducted

  Select

• Conducted on

  Date

• Prepared by

• Location
  Address

Page 1/5

QUALITY INSPECTION - CURTAIN WALLING - INTERNAL CHECK

• 1. Shoe / Head Brkt Isolation

  Yes

  No

  N/A

• 2. RAMS / CW Drawings approved. Datums / Grid Checked.

  Yes

  No

  N/A

• 3. Base / Head / Tie back Brkts correct torque. ( HSA M12x85 (2004154) EXPANSION ANCHORS .<br>(TORQUE = 50Nm)

  Yes

  No

  N/A

• 4. Transom / Mullion correct Interface gaps.

  Yes

  No

  N/A

• 5. Internal Gasket correctly installed (not lipped.)

  Yes

  No

  N/A

• 6. Internal Gasket / glass compression. 0.6 feeler gauge.

  Yes

  No

  N/A

• 7. Glazing units positioned centrally in rebate.

  Yes

  No

  N/A

QUALITY INSPECTION - CURTAIN WALLING - EXTERNAL CHECK

• 8. EPDM Installation Interfacing substrate and CW installed Substrate 75mm + 25mm termination 100mm total. 20-30mm on frame or mechanically fixed.

  Yes

  No

  N/A

• 9. Off site machining as per manufacturers recommendations.

  Yes

  No

  N/A

• 10. Correct transom drainage moulding to suit thermal break length & fabrication method.

  Yes

  No

  N/A

• 11. Sheer block/spring cleats in place.

  Yes

  No

  N/A

• 12. Correct transom fixing screw. Check transom face is aligned with mullion. 3.5Nm.

  Yes

  No

  N/A

Page 2/5

• 13. Correct sealant applied where required. Gaskets Butyl based sealant.

  Yes

  No

  N/A

• 14. Correct sealant applied to cut faces of mullion butt joints Low modulus Silicone Sealant.

  Yes

  No

  N/A

• 15. Correct gap maintained at expansion joint 10mm.

  Yes

  No

  N/A

• 16. Mullion joints/spigots/fixings and approved drawings as per manufacturers.

  Yes

  No

  N/A

• 17. Fixing brackets/shims to correct location & orientation.

  Yes

  No

  N/A

• 18. Glazing rebates are clean prior to fitting glazing/gaskets.

  Yes

  No

  N/A

• 19. Glazing gaskets correctly seated within gasket races ​ check corners.

  Yes

  No

  N/A

• 20. Thermal breaks correctly installed.

  Yes

  No

  N/A

• 21. Glass support positions correct Have increased glass load supports been used where applicable.

  Yes

  No

  N/A

• 22. Are stitch pressure plates adequate and have not been in-situ for too long.

  Yes

  No

  N/A

• 23. Pressure plates cut to correct length and correct orientation ​ check end seals.

  Yes

  No

  N/A

Page 3/5

• 24. Pressure plate end pads in place?

  Yes

  No

  N/A

• 25. All P/P fixings holes used. Check end dims and centres 50mm from end. then max 300mm centres.

  Yes

  No

  N/A

• 26. Ensure drainage paths are clear. Drainage spouts project through slots correctly

  Yes

  No

  N/A

• 27. Pressure plate screws torqued to correct level 3.5Nm.

  Yes

  No

  N/A

• 28. Drainage slot cover plates fitted.

  Yes

  No

  N/A

• 29. Any redundant pressure plate holes capped off with sealant.

  Yes

  No

  N/A

• 30. Sealant applied at head of pressure plate to prevent run off water entering.

  Yes

  No

  N/A

• 31. Check face caps are secure and no excessive gaps evident at mullion/transom joints.

  Yes

  No

  N/A

Page 4/5

Summary

Conclusion

• Signature

  Sign

• Date and Time

  Date

Page 5/5