ITP - Sheet Membrane - PVC - Butynol - Torch Membrane

• Site conducted

  Select

• Australseal Protective Solutions PL - ABN:68633653362 - admin@aspsau.com - 0448944893

• Location:
  Address

• Conducted on:

  Date

• Prepared by:

• Project Name:

  Select QN008 - Binah Botany Anlgicare QN022 - Binah Fairfield Anglicare QN025 - Hutchinson Builders Mainsbridge SSP Warwick Farm QN042 - Growthbuilt Mt Druitt SAHF2 Anglicare QN044 - Brae Group St Peters QN063 - Fal Construction Gilroy College QN065 - ICON East Gateway QN048 - Piety Beyond Hurstville QN056 - Mainbrace Schofield Town Centre QN029 -Kane Construction Cabramata Carpark QN123 - Girvan Group Chifley Square QN129 - Brae Group 639-641 Princes Highway Rockdale NSW

  • QN008 - Binah Botany Anlgicare
  • QN022 - Binah Fairfield Anglicare
  • QN025 - Hutchinson Builders Mainsbridge SSP Warwick Farm
  • QN042 - Growthbuilt Mt Druitt SAHF2 Anglicare
  • QN044 - Brae Group St Peters
  • QN063 - Fal Construction Gilroy College
  • QN065 - ICON East Gateway
  • QN048 - Piety Beyond Hurstville
  • QN056 - Mainbrace Schofield Town Centre
  • QN029 -Kane Construction Cabramata Carpark
  • QN123 - Girvan Group Chifley Square
  • QN129 - Brae Group 639-641 Princes Highway Rockdale NSW

• Manufacturer & Material(s) Used:

• Area(s) Completed:

Submission origin:

• E.g: Onsite / Offsite

  Onsite

  Offsite

Activity

• Substrate inspected and accepted. Substrate must be clean, smooth, dry and free from dust or contaminants. All sharp points and loose materials have been removed

  Yes

  No

  N/A

• Moisture content of substrate checked and accepted and is below acceptable level. (Non invasive procedure)

  Yes

  No

  N/A

• Primer, adhesive glues applied to relevant as per manufacturers standards and application guide as per product data sheet. This will not be relevant if loose laid mechanical fix is the specified system.

  Yes

  No

  N/A

• If Specified, Mechanically fixed as per wind load diagram and fixings to receive patching to veil penetrated fixings to horizontal substrate.

  Yes

  No

  N/A

• If required, coving fillet applied to all vertical/Horizontal construction joints

  Yes

  No

  N/A

• Sheet membrane installed to the correct manufacturers standards including over laps as per minimum manufacturers requirements and as per AS 4654:2012 and/or AS3740:2021

  Yes

  No

  N/A

• Check Laps, end laps fully/evenly sealed and closed, penetrations sealed, all penetrations have sufficient termination and clamps installed to terminate membrane as per manufacturers requirements or specified standards.

  Yes

  No

  N/A

• All welded seams tested with hook probe ensuring proper welds are complete.

  Yes

  No

  N/A

• Installation of pressure seals or liquid bandage termination installed to the correct manufacturers standards. Correct fillet or reglet termination sequencing completed as per manufacturers specified instructions and as per AS 4654:2012 and /or AS 3740:2021

  Yes

  No

  N/A

• Final Walk over with main contractor

  Yes

  No

  N/A

Final Inspection

• Client:

• Client Name & Signature:

  Sign

• Date:

  Date

• Australseal Representative Name & Signature:

  Sign

• Date:

  Date

• Photo 1

  Media

• Photo 2

  Media

• Photo 3

  Media

• Photo 4

  Media