MWSCISSOR3 (172893)
-
Site/project reference
-
Date of inspection
-
Completed by
-
Location where scissor lift will be used
Scissor lift/MEWP checklist
-
Type of MEWP: Make and Model
-
MEWP Serial No:
-
Site ID/reference for equipment?
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
IPAF trained operatives using equipment?
-
Operator Name(s)
-
PAL Card Number(s). (Unless numbers held on record in the office)
-
Visual inspection and general appearance of equipment
-
Current through examination certificate (within last 6 mths)
-
Documentation/instructions/manufacturer's operator manual held within safe box located on equipment?
-
Rescue plan discussed with operatives using equipment persons on the ground?
-
Wheels/Tyres in good condition?
-
Wheel security (nuts, retainers: loose, damaged, missing)
-
Tyre pressure (pneumatic, foam filled or solid)
-
Cuts, splits, exposed braiding, damaged rims?
-
Engine/Power
-
Fluid levels (engine oil, coolant, fuel)
-
Fluid leakage on ground and around engine
-
Battery (electrolyte, security and charging plug condition)
-
Hydraulic fluid level & other hydraulic items
-
Leaks (hoses, pipe connections, rams, cylinders)
-
Security and condition (cuts, chaffing, bulges)
-
Hoses & Cables
-
Power track cable trays (free from damage and debris)
-
General condition, pins/retainers, footplate
-
Outriggers, Stabilisers
-
Spreader plates (present, condition, secure for travel)
-
Interlocks (functioning, engaged)
-
General condition (damage, misalignment, corrosion)
-
Chassis, Boom & Scissor Pack
-
Cracks in welds
-
Pins, retainers and chains (security, signs of wear)
-
Canopies, guards, engine covers (security and condition)
-
Platform or Cage
-
Steps for access/egress (secure, undamaged, clear)
-
Entrance gate, guard rails and retaining pins
-
Harness anchor points
-
Decals/warning/hazard signage legible
-
Controls (identification decals, directional arrows)
-
Platform loads (SWL, max wind speed, max number of persons)
-
Function Checks
-
Security device (power isolator, keypad, smart card)
-
Function enable (ignition key, foot switch, hold to run device)
-
Emergency stops and emergency lowering system
-
All switches, function controls (move freely, do not stick)
-
Lifting functions (raise, lower, slew, tele-out, tele-in)
-
Travel functions (forward, reverse, steer, brakes)
-
Using Ground (G) and Platform (P) Controls
-
Elevated drive speed (reduced or prevented)
-
Lights, beacons, warning devices
-
Alarms (tilt, descent and travel)
-
Limit switches (e.g., descent, load, outreach, rotation)
-
Using Ground (G) and Platform (P) Controls
-
Pothole protection device fully deploys and retracts
-
Oscillating axle locks, extending axles
-
Accessories, power to platform, extending decks
-
Jacks-legs, stabilisers, outriggers, levelling devices
-
Comments- (issues or defects to be detailed here)
-
Name & signature of person inspecting equipment?
-
Daily: Sections below are to be filled in every day following a ‘pre-use walk round and check’ to confirm that items on the above checklist still apply and that the equipment is still safe to use.
-
Monday
-
If possible, attach photograph(s) of equipment (inc tags, labels & general condition)
-
Comments/issues
-
Inspected by
-
Tuesday
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
Comments/issues
-
Inspected by
-
Wednesday
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
Comments/issues
-
Inspected by
-
Thursday
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
Comments/issues
-
Inspected by
-
Friday
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
Comments/issues
-
Inspected by
-
Saturday
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
Comments/issues
-
Inspected by
-
Sunday
-
If possible, attach photograph(s) of equipment (inc tags and labels)
-
Comments/issues
-
Inspected by