Title Page
-
Site conducted
JL Grille Production LPA
-
Date:
-
Select a work area
-
Select the JL Grille workstation or cell/area
- Station 1 (Rivet)
- Station 2 (Welder)
- Station 5
- Station 6 (Rings/W Clips)
- Station 7 (Textures)
- Station 8 (Screws)
- Poka Yoke (Hood Seal and EOL)
- Texture/Ring Kitting
-
Select a JL/JT Carrier work station
- Rivnut 1
- Rivnut 2
- Turntable 3
- Turntable 4
- Turntable 5
- Turntable 6
- Limiter 1
- Limiter 2
- Limiter 3
-
Which shift are you auditing?
-
Your Name
-
Name of the operator that is being audited?
-
JL Grille - MGT SF 092-2 LPA Form Rev 0 content 11/16/18
Audit
-
High Risk - Verify the "Critical Safety/Quality" section of the OK to Produce Process was completed for this operation
-
Audit one of the following items from the OK to Produce for this process to verify compliance (Quality/Safety Alerts [no expired alerts posted], Training Matrix, First Piece Approval, In Process Verification). If a NC is found, alert the Production and Dept. Manager immediately.
-
High Risk - Verify there is a signed process/product deviation in place for any equipment, torques or labeling in by-pass and that the operator understands and is following the deviation
-
Verify an error proofing device works as intended. (Focus on high RPNs from the PFMEA) If not, is there a reaction plan for these devices?
-
Verify Rabbit documentation is filled out in accordance with the procedure using the proper nomenclature. (Are all error proofing devices verified as scheduled?)
-
Ensure the Standard Operation Sheet and Job Element Sheet are located in the work cell
-
Verify appropriate PPE is called out on the SOS and worn by the operator
-
Verify the Team Member is following the MES including any known quality issues
-
If the JES calls out any key process symbols or customer interface characteristics, verify the operator understands the reasoning behind the denoted checks
-
Does the team member understand what determines clean vs. soiled contents in a drum? (Refer to QA below)
-
Clean rags - yellow step can. Soiled rags - red step can.
-
High Risk - Verify any torques are at the correct setting and in compliance (torque settings are noted on the torque boxes)
-
Verify required inspections are being completed
-
If inspection is done at this station, are visual aids present? (select N/A if no inspection is conducted)
-
High Risk - Ensure quality gate/verification station operations for this part are being followed for any relevant customer or internal quality issues.
-
Verify corrective actions are in place for the NCTs below if they apply to the station being audited
-
NCT 21102778 - 08/25/2021 - Ensure operator tucks the camera wire harnesses as described in the alert below
-
Review packaging instructions and ensure stacking/packing techniques of parts is appropriate and safe. Ensure FIFO practices are being followed.
-
High Risk - Verify the operator is green in the OJT for all required operations
-
Review 3 completed product assemblies for conformance to the standard including proper part identification and packing technique
-
Is the line balance available in the work area?
-
Verify gauge instructions are available for all gauges in use for this program
-
Verify the Safety, Quality, Timing, Cost, and Morale metrics have been updated for the last working shift prior to the start of today's shift for that team. (Ex: 2nd shift needs to update the last 2nd shift metrics prior to the start of today's 2nd shift)
-
Example of acceptable status
-
Verify Autonomous Maintenance is up to date if applicable.
-
Are all master and secondary documents controlled with a form number?
-
Do all communication documents have a document name, initiator name and date?
-
Verify any non-conforming parts have been properly identified with a red tag/tape and placed in the NC area. Note, if any NC is found, an action item is required and NC must be contained/corrected within 24 hrs.
Level 4 LPA Only (AGM)
-
Verify the start-up and shut-down procedures are posted and signed off at each of the following machines
-
JL Limiter - Carrier Cell
-
JL Poka Yoke
-
801 Welder
-
802 Welder
-
JT Welder #2
-
JL Grille Conveyor
-
Assign an action item for any continuous improvement items
-
Please review any findings with the area TL or Production Manager
-
If you completed this audit on a shared device, please sign out of the device once you complete this audit.
