Sprinkler Acceptance Test

• Document No.

• Inspection Title

• Client / Site

• Conducted on

  Date

• Prepared by

• Location
  Address

• Fire Protection Contractor

General

• Approved drawing and above ground piping certification documents are on site.

  Yes

  No

  N/A

• Underground piping certification documents are provided.

  Yes

  No

  N/A

• Back flow prevention device is installed in accordance with the approved set of plans and forward flow tested, 24.2.5.

  Yes

  No

  N/A

• Operational test of the dry pipe valve is performed and the quick opening system (500+ gallon system) is tested, 750+gallon system must trip within 60 seconds.

  Yes

  No

  N/A

• Pressure reducing valves are tested at maximum and normal inlet pressures or as specified by the manufacturer, the supply pressure is recorded on the certificate, a relief valve is on the discharge side and gauges on each side of the valve, 25.2.4.

  Yes

  No

  N/A

Riser

• The main drain is routed to the exterior with a turned down elbow or an inside drain capable of handling the water flow. A flow test is performed. The main drain pipe is 3/4" or greater for a riser up to 2". 11/4" or greater for a riser 21/2" to 31/2", 2" for a riser 4" or greater, 8.16.2.4.2, 24.2.3.4.

  Yes

  No

  N/A

• Water control valves and flow switches are electronically tested and supervised, IFC 903.4.

  Yes

  No

  N/A

• Paddle type water flow is not allowed for dry, pre-action, or deluge systems.

  Yes

  No

  N/A

• 24 hr. monitoring service agency or remote supervising station or proprietary supervising station received signals, 903.4.1.

  Yes

  No

  N/A

• Water flow alarm is tested and initiates an alarm within 5 minutes, located in accordance with the approved set of plans, and it is properly signed, 24.2.3.1.

  Yes

  No

  N/A

• High rise: each floor system shall have water flow device with a test connection and be connected to the fire alarm system.

  Yes

  No

  N/A

• Permanent system identification signs for each control valve and what portion of the building each valve serves is provided, 6.7.4.

  Yes

  No

  N/A

• A permanent hydraulic nameplate is attached to the riser, 24.5.1. A general information sign that indicates the design capabilities and limitations of the automatic sprinkler system shall be provided at each system riser, antifreeze loop and auxiliary system control valve. The sign shall contain the required information specified in sections 24.6.2, 24.6.1.

  Yes

  No

  N/A

• Riser is supported by hangar or attachment, for multistory at the lowest level, each alternate level, above and below offsets, and at the top, 9.2.5.4.

  Yes

  No

  N/A

• Gauges are above and below the riser check valve, 7.1.1.2.

  Yes

  No

  N/A

• Tag certifying system completion is affixed.

  Yes

  No

  N/A

FDC

• FDC caps in place and permanently signed with system type, the required pressure to support the system if the pressure is equal to or greater than 150 psi, and are or building served, 8.17.2.4.7.

  Yes

  No

  N/A

• FDC has check valve and drip valve, 8.17.2.5.

  Yes

  No

  N/A

• FDC for wet single riser system connects to the system side, 8.17.2.4.

  Yes

  No

  N/A

• FDC for wet multi-riser system connects after the main system shut off valve, 8.17.2.4.

  Yes

  No

  N/A

• FDC for dry system connects between the indicating and dry pipe valves.

  Yes

  No

  N/A

• FDC pipe complies with the size indicated on the plans, 18" to 48" above grade, and properly supported, 8.17.2, A.8.17.2. Ensure that the minimum clearance to the sides, front, and height is provided in accordance with IFC 912.3.2.

  Yes

  No

  N/A

Sprinkler

• Spare sprinklers-Provide at least 6 spare sprinklers for systems designed with 300 or less sprinklers; 12 spare sprinklers for systems designed using 300-1000 sprinklers, and 24 spare sprinklers for systems designed using more than 1000 sprinklers, 6.2.9.

  Yes

  No

  N/A

• Replacement wrench(s) are provided, 6.2,9.

  Yes

  No

  N/A

• Sprinklers shall be a minn. of 4" from the wall and be properly spaced, 8.6.3.3.

  Yes

  No

  N/A

• Sprinkler heads have a guard if subject to damage.

  Yes

  No

  N/A

• Sprinkler heads are not painted or covered.

  Yes

  No

  N/A

• ESFR upright deflectors are a minimum of 7" above the top of the pipe, 8.12.5.3.3.1.

  Yes

  No

  N/A

• ESFR sprinklers are at least 1 foot horizontally from the bottom edge of bar joist or open truss and at least 3 ft. Above the top of the storage level, 8.12.6.

  Yes

  No

  N/A

• Proper type and temperature sprinklers are used and match plans.

  Yes

  No

  N/A

• Escutcheon plates are installed.

  Yes

  No

  N/A

• Sprinklers are not obstructed, 8.5.5-8.12.5.

  Yes

  No

  N/A

Pipe: Hangars, Seismic, and Penetrations

• Piping layout and size are the same as on the approved set of plans.

  Yes

  No

  N/A

• Pipe penetrations have proper clearance 2" for pipe 1" to 3.5", 4" for pipe 4" and larger, 9.3.

  Yes

  No

  N/A

• When flexible couplings are used in risers, above and below floor penetrations of multistory structures, near penetrations of concrete or masonry walls, and near expansion joints, their location is in accordance with sections 9.3.2.1-9.3.2.4.

  Yes

  No

  N/A

• Minimum clearance around pipes penetrating construction elements listed in 9.3.4.1 is in accordance with 9.3.4.2 unless the requirements of 9.3.4.3-9.3.4.7 are met.

  Yes

  No

  N/A

• A seismic separation assembly is provided at building seismic joints, 9.3.3.

  Yes

  No

  N/A

• Lateral sway bracing is provided and spaced in accordance with the approved set of plans for all mains, cross ,aims, and branch lines 2.5" or larger.

  Yes

  No

  N/A

• Fire Protection Contractor

  Sign

• Foley Fire Inspector

  Sign